| Age | Commit message (Collapse) | Author |
|---|
|
This patch enables ethernet support for ls1012ardb.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Changes in v2:
-split from original patch "board: freescale: ls1012a: enable network
support on ls1012a platforms"
-fix RGMII TX-delay issue
|
|
This patch enables ethernet support for ls1012frdm.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Changes in v2:
-split from original patch "board: freescale: ls1012a: enable network
support on ls1012a platforms"
|
|
This patch enables ethernet support for ls1012aqds.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Changes in v2:
-split from original patch "board: freescale: ls1012a: enable network
support on ls1012a platforms"
|
|
Contains all the pfe header files.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Changes in v2:
-Add pfe_rx_done to clear bd after packet processing
-remove unused code under CONFIG_UTIL_PE_DISABLED
-Used BIT and GENMASK macros wherever applicable
-Removed generic definitions that pollutes namespace
|
|
pfe_command provides command line support for several features that
support pfe like starting or stopping the pfe, checking the health
of the processor engines and checking status of different unit inside
pfe.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Changes in v2:
-remove unused code under CONFIG_UTIL_PE_DISABLED
-remove unused code under CONFIG_PFE_WARN_WA
|
|
This patch adds PFE driver into U-Boot.
Following are the main driver files:-
pfe.c: provides low level helper functions to initialize PFE internal
processor engines and other hardware blocks.
pfe_driver.c: provides probe functions, initialization functions
and packet send and receive functions.
pfe_eth.c: provides high level gemac, phy and mdio initialization
functions.
pfe_firmware.c: provides functions to load firmware into PFE
internal processor engines.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Changes in v2:
-fix RGMII TX-delay issue
-add pfe_rx_done to clear bd after packet processing
-use writel/readl to access hw bds
-cleanup typos and indent
-remove unused code under CONFIG_UTIL_PE_DISABLED
-Consolidate code in pfe_lib_init
-Corrected typo receive
-Magic numbers replaced with proper definitions
|
|
Layerscape Gen2 SoC supports GPIO registers to control GPIO
signals. Adding support of GPIO structure to access GPIO
registers.
Signed-off-by: Pratiyush Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Changes in v2: None
|
|
Enable support for multiple loadable images in SEC firmware FIT image.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
|
|
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
|
|
For for case of lazyapply method, API fdt_fixup_board_enet() gets invoked
before DPL being deployed.
This leads to an issue that fsl-mc fdt fixup status marked as fail and
dprc driver didn't get registered in linux boot.
Fixes this issue by calling fdt_fixup_board_enet() for case when
DPL is deployed successfully in lazyapply method.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
v1: Incorporated Prabhakar review comments.
|
|
The QSPI support the direct 4bytes address command for flash
read/write/erase.
And the address can cover the whole QSPI memory space.
signed-off-by: Yuan Yao <yao.yuan@nxp.com>
|
|
Some new flash don't support bar register but use 4bytes address to
support exceed 16MB flash size.
So add flash flag: ADDR_4B
for some flash which support 4bytes address.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
|
|
LS1012A-2G5RDB belongs to LS1012A family with features
2 2.5G SGMII PFE MAC, SATA, USB 2.0/3.0, WiFi
DDR, eMMC, QuadSPI, UART
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
|
|
Align boards belonging to LS1012A, LS2080A SoC at
one place
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
|
|
ENV variables can now be used before relocation.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
|
|
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
|
|
IFC-NOR and QSPI-NOR pins are muxed on SoC,so they
cannot be accessed simultaneously, but
IFC-NOR can be accessed along with SD-BOOT.
ls1088aqds_sdcard_ifc_defconfig: is defconfig for
SD as boot source and IFC-NOR to be used as flash,
this will be used to write IFC-NOR image on IFC flash.
QSPI and DSPI cannot be accessed in this defconfig.
IFC-NOR image is generated by ls1088aqds_defconfig.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
|
|
The SP805-WDT module on LS1088A requires configuration of PMU's
PCTBENR register to enable watchdog counter decrement and reset
signal generation. The watchdog clock needs to be enabled first.
Signed-off-by: Zhang Ying-22455 <ying.zhang22455@nxp.com>
|
|
The iommu-map property in the fsl-mc node is updated by
valid stream-ids by u-boot. This patch is to fixup this
property for LS208x and LS1088.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
|
|
As per data sheet, S25FS512S support Uniform sector option
or erase size of 256 kbytes and Page Programming buffer of
256 or 512 Bytes. So, flag SECT_4K have no significance
for this flash.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
|
|
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
|
|
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
|
|
Identify and distinguish between platform device type of MX7ULP
and LS1021A.
This is a fix to: 7edf5c45 serial: lpuart: add i.MX7ULP support
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
|
|
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
|
|
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
|
|
Enable CONFIG_SYS_DCACHE_OFF in case of SPL build as DCACHE is
not being enabled in case of SPL image but was compiled in to
add redundant code.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
|
|
As part of chain of trust with confidentiality along with distro
boot, linux kernel image needs to be stored in encrypted form on
ext4 boot partition. So enable CONFIG_CMD_EXT4_WRITE in case of
Secure boot.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
|
|
Remove duplicate macro CONFIG_FSL_PCIE_RESET and update its comment.
It enables PCIe reset to fix link width 2x - 4x.
Signed-off-by: Bao Xiaowei <xiaowei.bao@nxp.com>
|
|
Using changes in this patch we were able to reduce approx 8k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1088a/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1088a/ls1088a.c to keep
board_early_init_f funcations in case of SPL build.
3. Changes in ls1088a_common.h & ls1088ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
|
|
Using changes in this patch we were able to reduce approx 4k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Compile-off mp.c and libfdt.c in case of SPL build.
2. Keep MMU and DCACHE specific variable and functions under
CONFIG_SYS_DCACHE_OFF macro.
3. Compile-off IFC specific funtion call "init_early_memctl_regs"
in case of SPL build.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
|
|
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment. Enable fall back option to
qspi boot in case of secure boot.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
|
|
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
|
|
Force delay 10ms between each control messages to fix Transcend
and Kingston DT 101 G2 USB2.0 stick fail to be enumerated by LS208xA.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
|
|
Rename to USB_EHCI_FSL, use Kconfig to select ehci accordingly.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
|
|
When enable CONFIG_HAS_FSL_DR_USB, we might encounter below compile
warning, apply this patch can fix it:
drivers/usb/host/ehci-fsl.c:109:4: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
((u32)hccr + HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
^
drivers/usb/host/ehci-fsl.c:108:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
hcor = (struct ehci_hcor *)
^
drivers/usb/host/ehci-fsl.c:115:8: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
(u32)hccr, (u32)hcor,
^
include/log.h:131:26: note: in definition of macro 'debug_cond'
printf(pr_fmt(fmt), ##args); \
^~~~
drivers/usb/host/ehci-fsl.c:114:2: note: in expansion of macro 'debug'
debug("ehci-fsl: init hccr %x and hcor %x hc_length %d\n",
^~~~~
drivers/usb/host/ehci-fsl.c:115:19: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
(u32)hccr, (u32)hcor,
^
include/log.h:131:26: note: in definition of macro 'debug_cond'
printf(pr_fmt(fmt), ##args); \
^~~~
drivers/usb/host/ehci-fsl.c:114:2: note: in expansion of macro 'debug'
debug("ehci-fsl: init hccr %x and hcor %x hc_length %d\n",
^~~~~
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
|
|
Without this propertiy, U-Boot will pop warning of 'USB phy type not
defined' when select CONFIG_HAS_FSL_DR_USB.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
|
|
The CONFIG_SYS_DPAA_QBMAN define is used by DPAA1 freescale SOCs to
add device tree fixups that allow deep sleep in Linux. The define was
placed in header files included by a number of boards, but was not
explicitly documented in any of the Kconfigs. A description was added
to the drivers/networking menuconfig and default selection for
current SOCs that have this part
Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Series-version: 5
Series-changes: 4
- Add QBMan support in Kconfig auto select for B4420 and T4160 SOCs
Series-changes: 5
- Add net device to T1024QDS_DDR4_defconfig to enable QBMan fixup
- Remove QBMan define in kmp204x-common.h and rely on SOC auto select
Cover-letter:
arm: ppc: Share DPAA1 fixups between ARCHs
- Support DPAA1 QBMan device tree fixups in a shared location for both
arm and ppc architectures
- cleanup a define from header files and add as Kconfig with auto
selection based on SOC
END
Series-to: Joe Hershberger <joe.hershberger@ni.com>
Series-to: York Sun <york.sun@nxp.com>
Series-to: Roy Pledge <roy.pledge@nxp.com>
Series-to: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
|
This patch adds changes necessary to move functionality present in
PowerPC folders with ARM architectures that have DPAA1 QBMan hardware
- Create new board/freescale/common/fsl_portals.c to house shared
device tree fixups for DPAA1 devices with ARM and PowerPC cores
- Add new header file to top includes directory to allow files in
both architectures to grab the function prototypes
- Port inhibit_portals() from PowerPC to ARM. This function is used in
setup to disable interrupts on all QMan and BMan portals. It is
needed because the interrupts are enabled by default for all portals
including unused/uninitialised portals. When the kernel attempts to
go to deep sleep the unused portals prevent it from doing so
Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Series-changes: 2
- Add get_qman_freq() to replace get_sys_info() for readability
- Correct the copyright year in new files
- Replace !ARM with PPC to wall off PowerPC SOCs specific qman setup
- Rename portals.c -> fsl_portals.c for clarity
Series-changes: 3
- Add freescale old copyright in new file since it is a modified copy
- Add ifdef QBMAN guard around get_qman_freq()
- Return freq_qman instead of freq_systembus. More readable and robust
- Add white space before return line in get_qman_freq()
Series-changes: 4
- Update function name setup_portals() to setup_qbman_portals() in
files that were missed the first time
Series-changes: 5
- Include <fsl_qbman.h> to fix missing prototype in p1023rdb.c
|
|
Sata is equipped on ls1012a and can be a boot source.
Add sata boot support as a option if available.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
|
|
Sata is equipped on ls1046a and can be a boot source.
Add sata boot support as a option if available.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
|
|
855873: An eviction might overtake a cache clean operation
Workaround: The erratum can be avoided by upgrading cache clean by
address operations to cache clean and invalidate operations. For
Cortex-A53 r0p3 and later release, this can be achieved by setting
CPUACTLR.ENDCCASCI to 1.
This patch is to implement the workaround for this erratum.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
|
|
Linux device tree contains "ethernet" node for all possible
interface supported by SoC i.e. LS1046A.
It is not necessary for a SerDes protocol to support all possible
interface. So disable unavailable "ethernet" node in device tree.
Also, enable FDT_SEQ_MACADDR_FROM_ENV to fetch MAC address
sequentially from environment variables
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
"ethernet" node fix-up for device tree happens before Linux boot.
There can be requirement of updating "ethernet" node even before
fix-up. So, add support of updating "ethernet" node.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
The MAC addresses get fixed in the device tree for "ethernet" nodes
is by using trailing number behind "ethernet" found in "/aliases".
It may not be necessary for the "ethernet" nodes to be sequential.
There can be gaps in between or any node disabled
So provide a support to fetch MAC addr sequentially from env
and apply them to "ethernet" nodes in the order they appear in
device tree only if "ethernet" is not "disabled"
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Increase setup, assertion and hold time related to chip-select signal.
Additional delay is needed for the signal to propogate through FPGA.
This adjustment slightly increase the read and write cycle but has no
impact on burst read or write.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Update README file to note LS2088A and LS1088A don't support booting
from NAND flash.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Again the image size increases and the length needs to be adjusted.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
I2C reading for DIP switch setting is not reliable for LS1012ARDB
RevD and later versions. This patch is to add hwconfig support to
enable/disable eSDHC1 manually for these boards. Also drop 'status'
fix-up for eSDHC0 and leave it as it is. It shouldn't always be
fixed up with 'okay'.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Add LS1012ARDB RevC/RevC1/RevC2/RevD/RevE information and
detect it when u-boot starts up.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
This patch is to clean up definitions for I2C IO expanders.
The value 0x10 of __SW_BOOT_EMU is wrong. It should be 0x2.
Fixed it in this patch.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
