summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/armv7/omap3/board.c
AgeCommit message (Collapse)Author
2015-10-22omap-common: Common function to display die id, replacing omap3-specific versionPaul Kocialkowski
This introduces omap_die_id_display to display the full die id. There is no need to store it in an environment variable, that no boot script is using anyway. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-13gpio: omap: Drop 'method' parameterTom Rini
The "method" parameter was part of the original port of the driver from the kernel. At some point this may have been added to allow for future differentiation (as omap1 and omap2 have different GPIO IP blocks, so this wasn't an unreasonable thing to do). At this point however it's just extra overhead, so drop. Signed-off-by: Tom Rini <trini@konsulko.com>
2015-07-27omap-common: Common boot code OMAP3 support and cleanupPaul Kocialkowski
This introduces OMAP3 support for the common omap boot code, as well as a major cleanup of the common omap boot code. First, the omap_boot_parameters structure becomes platform-specific, since its definition differs a bit across omap platforms. The offsets are removed as well since it is U-Boot's coding style to use structures for mapping such kind of data (in the sense that it is similar to registers). It is correct to assume that romcode structure encoding is the same as U-Boot, given the description of these structures in the TRMs. The original address provided by the bootrom is passed to the U-Boot binary instead of a duplicate of the structure stored in global data. This allows to have only the relevant (boot device and mode) information stored in global data. It is also expected that the address where the bootrom stores that information is not overridden by the U-Boot SPL or U-Boot. The save_omap_boot_params is expected to handle all special cases where the data provided by the bootrom cannot be used as-is, so that spl_boot_device and spl_boot_mode only return the data from global data. All of this is only relevant when the U-Boot SPL is used. In cases it is not, save_boot_params should fallback to its weak (or board-specific) definition. save_omap_boot_params should not be called in that context either. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2015-03-13ARM: OMAP3: rx51: Enable workaround for ARM errata 454179, 430973, 621766Nishanth Menon
RX51 has a secure logic which uses different parameters compared to traditional implementation. So, make the generic secure acr write over-ride-able by board file and refactor rx51 code to use this. While at it, enable the OMAP3 specific errata code for 454179, 430973, 621766. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13ARM: OMAP3: Enable workaround for ARM errata 454179, 430973, 621766Nishanth Menon
Enable the OMAP3 specific errata code for 454179, 430973, 621766 and while at it, remove legacy non-revision checked errata logic. Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13ARM: OMAP3: Get rid of omap3_gp_romcode_call and replace with omap_smc1Nishanth Menon
omap_smc1 is now generic enough to remove duplicate omap3_gp_romcode_call logic that omap3 introduced. As part of this change, move to using the generic lowlevel_init.S for omap3 as well. Signed-off-by: Nishanth Menon <nm@ti.com> Tested-by: Matt Porter <mporter@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-06omap: gpmc: 'nandecc sw' can use HAM1 or BCH8Ash Charles
The 'nandecc sw' command selects a software-based error correction algorithm. By default, this is OMAP_ECC_HAM1_CODE_SW but some platforms use OMAP_ECC_BCH8_CODE_HW_DETECTION_SW as their software-based correction algorithm. Allow a user to be specific e.g. # nandecc sw <hamming|bch8> where 'hamming' is still the default. Note: we don't just use CONFIG_NAND_OMAP_ECCSCHEME as it might be set to a hardware-based ECC scheme---a little strange when the user has requested 'sw' ECC. Signed-off-by: Ash Charles <ashcharles@gmail.com>
2015-03-04ti: armv7: Move SPL SDRAM init to the right place, drop unused CONFIG_SPL_STACKSimon Glass
Currently in some cases SDRAM init requires global_data to be available and soon this will not be available prior to board_init_f(). Adjust the code paths in these cases to be correct. In some cases we had the SPL stack be in DDR as we might have large stacks (due to Falcon Mode + Environment). In these cases switch to CONFIG_SPL_STACK_R. In other cases we had simply been setting CONFIG_SPL_STACK into SRAM. In these cases we no longer need to (CONFIG_SYS_INIT_SP_ADDR is used and is also in SRAM) so drop those lines. Signed-off-by: Simon Glass <sjg@chromium.org> Tested on Beagleboard, Beagleboard xM Tested-by: Matt Porter <mporter@konsulko.com> Tested on Beaglebone Black, AM43xx GP EVM, OMAP5 uEVM, OMAP4 Pandaboard Tested-by: Tom Rini <trini@konsulko.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2015-01-16TI ARMv7: Don't use GD before crt0.S has set itTom Rini
Prior to this change we set the gd pointer early so that we can store data in it. This becomes problematic for DM changes as well as being odd in general. Re-work the code paths so that we don't need to set the gd pointer so early and instead can rely upon the normal setting of it. In order to do this we do need to move certain calls from s_init into spl_board_init(), mainly preloader_console_init and save_omap_boot_params. Tested on: Beaglebone Black, AM43xx GP EVM, Beagleboard, Beagleboard xM, OMAP5 uEVM, DRA7xx EVM Signed-off-by: Tom Rini <trini@ti.com> Tested-by: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2014-10-27Rename some defines containing FAT in their name to be filesystem genericGuillaume GARDET
Rename some defines containing FAT in their name to be filesystem generic: MMCSD_MODE_FAT => MMCSD_MODE_FS CONFIG_SPL_FAT_LOAD_ARGS_NAME => CONFIG_SPL_FS_LOAD_ARGS_NAME CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME => CONFIG_SPL_FS_LOAD_PAYLOAD_NAME CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION => CONFIG_SYS_MMC_SD_FS_BOOT_PARTITION Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Cc: Tom Rini <trini@ti.com>
2014-10-26Merge git://git.denx.de/u-boot-dmTom Rini
Fix a trivial conflict over adding <dm.h> Conflicts: arch/arm/cpu/armv7/omap3/board.c Signed-off-by: Tom Rini <trini@ti.com>
2014-10-25omap3: board: add missing include and protoJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25omap3: make local functions staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-24dm: omap3: Move to driver model for GPIO and serialSimon Glass
Adjust the configuration for the am33xx boards, including beagleboard, to use driver model. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Tom Rini <trini@ti.com>
2014-07-01Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-06-19omap3: board: trivial: add void for no argsJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-06-11am33xx/omap: Allow cache enable for all Sitara/OMAPSimon Glass
Enable the cache for all devices, unless CONFIG_SYS_DCACHE_OFF is defined. This speeds up the Beaglebone Black boot considerable. (Tested only on Beaglebone Black with SD card boot) Signed-off-by: Simon Glass <sjg@chromium.org>
2014-04-17ARM: OMAP: remove sr32() from OMAP board codeWolfgang Denk
Replace the custom sr32() bit manipulation function in arch/arm/cpu/armv7/omap3/board.c and board/ti/panda/panda.c by standard I/O accessors. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-11-13i2c, omap24xx: convert driver to new mutlibus/mutliadapter frameworkHeiko Schocher
- add omap24xx driver to new multibus/multiadpater support - adapted all config files, which uses this driver Tested on the am335x based siemens boards rut, dxr2 and pxm2 posted here: http://patchwork.ozlabs.org/patch/263211/ Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Tom Rini <trini@ti.com> Cc: Lars Poeschel <poeschel@lemonage.de> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Thomas Weber <weber@corscience.de> Cc: Tom Rix <Tom.Rix@windriver.com> Cc: Grazvydas Ignotas <notasas@gmail.com> Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Luca Ceresoli <luca.ceresoli@comelit.it> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Nishanth Menon <nm@ti.com> Cc: Pali Rohár <pali.rohar@gmail.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Michael Jones <michael.jones@matrix-vision.de> Cc: Raphael Assenat <raph@8d.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Stefano Babic <sbabic@denx.de>
2013-07-24Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
2013-04-08omap_gpmc: change nandecc commandAndreas Bießmann
With uppcoming BCH support on OMAP devices we need to decide between differnt algorithms when switching the ECC engine. Currently we support 1-bit hammign and 8-bit BCH on HW backend. In order to switch between differnet ECC algorithms we need to change the interface of omap_nand_switch_ecc() also. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Tom Rini <trini@ti.com> Cc: Thomas Weber <thomas.weber.linux@googlemail.com>
2013-03-11OMAP3: Initialize gpmc if SPL_ONENAND_SUPPORT is enabled.Enric Balletbo i Serra
In order to use SPL boot from OneNAND we should initialize the gpmc. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2013-03-08omap_hsmmc: add driver check for write protectionNikita Kiryanov
Add check for write protection in omap mmc driver. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
2013-03-08omap_hsmmc: implement driver check for card detectionNikita Kiryanov
Implement driver check for card detection. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-12-10omap3: Add a few comments to "#endif"s for readability.Robert P. J. Day
No functional changes, just more comments for readability when a preprocessor check spans more than a few lines, and for consistency. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2012-10-31omap3: Rework board.c for !CONFIG_SYS_L2CACHE_OFFTom Rini
When CONFIG_SYS_L2CACHE_OFF is defined we end up with a few warnings currently. Re-order functions so that we don't have that anymore. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27SPL: Create arch/arm/lib/spl.c for board_init_f and jump_to_image_linuxTom Rini
In SPL (CONFIG_SPL_FRAMEWORK) board_init_f must setup the stack pointer, clear the BSS and call board_init_r. We mark this as weak as some platforms may need to perform additional initalization at this point. We provide a gd that we know will be in a usable location, once the BSS has been cleared to help with this as well. Finally, we no longer call relocate_code so remove that from the armv7 version. Next, both board_init_f and jump_to_image_linux are going to be inherently arch-specific, so move these versions to arch/arm/lib/spl.c Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27SPL: Move the omap SPL framework to common/splTom Rini
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL framework, enable on all of the previously using boards. We move the spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/. We leave the NAND one in-place as we plan to replace it later in this series. We use common/spl to avoid linker problems with respect to merging constant strings in objects. Otherwise all strings in common/ will be linked in and kept which grows SPL in size too much. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27ARM: SPL: Move gpmc_init() to spl_board_init()Tom Rini
This is an OMAP/related-specific function, move calling it to spl_board_init() and turn on CONFIG_SPL_BOARD_INIT on the boards that enabled NAND and didn't enable this already. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27ARM: SPL: Make spl_mmc.c more genericTom Rini
Move the default omap/related-centric board_mmc_init to arch/arm/cpu/armv7/omap-common/boot-common.c and move the type defines to <asm/spl.h>. Also use mmc->read_bl_len rather than MMCSD_SECTOR_SIZE Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27ARM: SPL: Add <asm/spl.h> and <asm/arch/spl.h>Tom Rini
Move the SPL prototypes from <asm/omap_common.h> into <asm/spl.h> and add <asm/arch/spl.h> for arch specific portions of CONFIG_SPL_FRAMEWORK. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27ARM: SPL: Remove NAND_MODE_HW_ECC from spl_nand.cTom Rini
This detection code doesn't (and can't) do anything currently, so remove. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27ARM: SPL: Rename omap_boot_mode to spl_boot_mode()Tom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27ARM: SPL: Rename omap_boot_device to spl_boot_deviceTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15omap3: Introduce weak misc_init_rTom Rini
Introduce a __weak misc_init_r function that just runs dieid_num_r(). Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was all they did for misc_init_r. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-03-27OMAP3: SPL: do not call I2C init if no I2C is set.Stefano Babic
Call i2c initialization in spl_board_init only if I2C is configured for the board. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <tom.rini@gmail.com> CC: Wolfgang Denk <wd@denx.de> CC: Simon Schwarz <simonschwarzcor@gmail.com>
2012-02-27armv7: omap3: leave outer cache enabledAneesh V
Mainline kernel for OMAP3 doesn't enable L2 cache It expects L2$ to be enabled by ROM-code/bootloader. Leaving L2$ enabled can be troublesome in cases where the L2 cache is not under CP15 control, such as in Cortex-A9. This problem is explained in detail in the commit dc7100f4080952798413fb63bb4134b22c57623a However, this problem doesn't apply to Cortex-A8 because L2$ in Cortex-A8 is under CP15 control and hence the generic armv7 maintenance opertions work for it. As such we can make an exception for OMAP3 and leave the L2$ enabled when we jump to kernel. This is done by removing the strongly-linked implementation of v7_outer_cache_disable() and allowing it to fall back to the weakly linked implementation that doesn't do anything. Signed-off-by: Aneesh V <aneesh@ti.com>
2012-02-12omap3: fix comment typosPeter Meerwald
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
2012-02-12OMAP3+: Clock: Adding ehci clock enablingGovindraj.R
Adding ehci clock enabling mechanism part of clock framework. When essential clocks are enabled during init phase usb host clocks can also be enabled from clock framework. Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Govindraj.R <govindraj.raja@ti.com> Tested-by: Stefano Babic <sbabic@denx.de>
2012-01-16OMAP SPL: call timer_init in s_init to make udelay work earlierAndreas Müller
Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
2011-12-06OMAP3: Add SPL_BOARD_INIT hookTom Rini
Add an SPL_BOARD_INIT hook and for OMAP3 have it turn on i2c. OMAP4 doesn't need i2c enabled in SPL. Enable SPL_BOARD_INIT on devkit8000. Cc: Frederik Kriewitz <frederik@kriewitz.eu> Signed-off-by: Tom Rini <trini@ti.com>
2011-11-29OMAP3: Use sdelay from arch/arm/cpu/armv7/syslib.c instead of cloning that.Alexander Holler
There is no need to have such a function twice. Signed-off-by: Alexander Holler <holler@ahsoftware.de> Acked-by: Dirk Behme <dirk.behme@googlemail.com> Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-10-27OMAP3 SPL: Provide weak omap_rev_stringTom Rini
We add an weak version of omap_rev_string in omap-common/spl.c and while at it drop the omap3 version. Move the prototype over to <asm/omap_common.h> with the other SPL functions. Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30omap-common: add nand spl supportSimon Schwarz
Add NAND support for the new SPL structure. Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-04omap: enable caches at system start-upAneesh V
Signed-off-by: Aneesh V <aneesh@ti.com>
2011-09-04omap: fix gpio related build breaksAneesh V
Signed-off-by: Aneesh V <aneesh@ti.com> Acked-by: Dirk Behme <dirk.behme@googlemail.com>
2011-08-03omap: reuse omap3 gpio support in omap4Aneesh V
Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-07-04armv7: adapt omap3 to the new cache maintenance frameworkAneesh V
adapt omap3 to the new layered cache maintenance framework Signed-off-by: Aneesh V <aneesh@ti.com>
2010-09-08ARMV7: OMAP3: Convert setup_auxcr() to pure asmMans Rullgard
This function consists entirely of inline asm statements, so writing it directly in a .S file is simpler. Additionally, the inline asm is not safe as is, since registers are not guaranteed to be preserved between asm() statements. Signed-off-by: Mans Rullgard <mans@mansr.com> Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-07-05ARM: Rename arch/arm/cpu/arm_cortexa8 to armv7Steve Sakoman
The purpose of this patch is to prepare for adding the OMAP4 architecture, which is Cortex A9 Cortex A8 and A9 both belong to the armv7 architecture, hence the name change. The two architectures are similar enough that substantial code can be shared. Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
generated by cgit v0.10.2 at 2024-08-16 09:30:19 (GMT)