| Age | Commit message (Collapse) | Author |
|---|
|
This moves what was in arch/arm/cpu/armv7/omap-common in to
arch/arm/mach-omap2 and moves
arch/arm/cpu/armv7/{am33xx,omap3,omap4,omap5} in to arch/arm/mach-omap2
as subdirectories. All refernces to the former locations are updated to
the current locations. For the logic to decide what our outputs are,
consolidate the tests into a single config.mk rather than including 4.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Move this option to Kconfig and tidy up existing uses. Also add a function
comment to the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Adds a secure dram reservation fixup for secure
devices, when a region in the emif has been set aside
for secure world use. The size is defined by the
CONFIG_TI_SECURE_EMIF_TOTAL_REGION_SIZE config option.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Create a few public APIs which rely on secure world ROM/HAL
APIs for their implementation. These are intended to be used
to reserve a portion of the EMIF memory and configure hardware
firewalls around that region to prevent public code from
manipulating or interfering with that memory.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Adds start address and size config options for setting aside
a portion of the EMIF memory space for usage by security software
(like a secure OS/TEE). There are two sizes, a total size and a
protected size. The region is divided into protected (secure) and
unprotected (public) regions, that are contiguous and start at the
start address given. If the start address is zero, the intention
is that the region will be automatically placed at the end of the
available external DRAM space.
Signed-off-by: Daniel Allred <d-allred@ti.com>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this option to Kconfig and tidy up existing uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
gpio_en field is introduced to detect if pmic is controlled by GPIO.
Make this field 0 on all TPS659* pmics available on DRA7/OMAP5 based platforms
and remove the #ifndefs.
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
We need to ensure that CONFIG_PHYS_64BIT is configured via Kconfig so
that it is always available to the build system. Otherwise we can run
into cases where we have inconsistent sizes of certain attributes.
Ravi Babu reported offset mismatch of struct dwc3 across files since
commit 95ebc253e6d4 ("types.h: move and redefine resource_size_t").
Since the commit, resource_addr_t points to phys_addr_t, whose size
is dependent on CONFIG_PHYS_64BIT for ARM architecture.
I tried my best to use "select" where possible (for example, ARMv8
architecture) because I think this kind of option is generally user-
unconfigurable. However, I see some of PowerPC boards have 36BIT
defconfigs as well as 32BIT ones. I moved CONFIG_PHYS_64BIT to the
defconfigs for such boards.
CONFIG_36BIT is no longer referenced, so all of the defines were
removed from CONFIG_SYS_EXTRA_OPTIONS.
Fixes: 95ebc253e6d4 ("types.h: move and redefine resource_size_t")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Ravi Babu <ravibabu@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
According to AM572x DM SPRS953A, QSPI bus speed can be 76.8MHz, hence
update QSPI input clock divider value (DPLL_PER_HS13) to provide 76.8MHz
clock, so that driver can use the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
Commit 17c2987 introduces an undesired dependency on CONFIG_SPL_LOAD_FIT
when building U-Boot for AM57xx and DRA7xx high-security (HS) devices that
causes the build to break when that option is not active. Fix this issue
by only building the u-boot_HS.img target when building U-Boot into an
actual FIT image.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Modify the SPL build procedure for AM57xx and DRA7xx high-security (HS)
device variants to create a secure u-boot_HS.img FIT blob that contains
U-Boot and DTB artifacts signed with a TI-specific process based on the
CONFIG_TI_SECURE_DEVICE config option and the externally-provided image
signing tool.
Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
board/am57xx supports all boards based on am57xx. Rename the taget
as TARGET_AM57XX_EVM.
Fixes: 74cc8b097d9af ("board: ti: beagle_x15: Rename to indicate support for TI am57xx evms")
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Currently omap_vcores which holds pmic data is being assigned based
on the SoC type. PMIC is not a part of SoC. It is logical to
to assign omap_vcores based on board type. Hence over ride the
vcores_init function and assign omap_vcores based on the board type.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
The voltage values for each voltage domain at an OPP is identical
across all the SoCs in the DRA7 family. The current code defines
one set of macros for DRA75x/DRA74x SoCs and another set for DRA72x
macros. Consolidate both these sets into a single set.
This is done so as to minimize the number of macros used when voltage
values will be added for other OPPs as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Define a set of common macros for the efuse register offsets
(different for each OPP) that are used to get the AVS Class 0
voltage values and ABB configuration values. Assign these
common macros to the register offsets for OPP_NOM by default
for all voltage domains. These common macros can then be
redefined properly to point to the OPP specific efuse register
offset based on the desired OPP to program a specific voltage
domain.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
DRA7xx has a 32KHz PHY clock for USB_PHY3 that must be enabled
for USB1 instance in Super-Speed.
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
|
CONFIG_USB_XHCI_OMAP is enabled for host mode independent of CONFIG_USB_DWC3
which is meant for gadget mode only. We need enable/disbale_usb_clocks() for
host mode as well so provide for it.
Fixes: 09cc14f4bcbf ("ARM: AM43xx: Add functions to enable and disable USB clocks"
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
|
Adds an fdt.c file in that defines the ft_cpu_setup() function,
which should be called from a board-specific ft_board_setup()).
This ft_cpu_setup() will currently do nothing for non-secure (GP)
devices but contains pertinent updates for booting on secure (HS)
devices.
Update the omap5 Makefile to include the fdt.c in the build.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Updates the SPL build so that when CONFIG_TI_SECURE_DEVICE
is in use (which it should be when building for secure parts),
the TI secure development package is used to create a valid
secure boot image. The u-boot SPL build processes is NOT aware
of the details of creating the boot image - all of that information
is encapsulated in the TI secure development package, which is
available from TI. More info can be found in README.ti-secure
Right now, two image types are generated, MLO and X-LOADER. The types
are important, as certain boot modes implemented by the device's ROM
boot loader require one or the other (they are not equivalent). The
output filenames are u-boot-spl_HS_MLO and u-boot-spl_HS_X-LOADER. The
u-boot-spl_HS_MLO image is also copied to a file named MLO, which is
the name that the device ROM bootloader requires for loading from the
FAT partition of an SD card (same as on non-secure devices).
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
ABB should be initialized for all required domains voltage domain
for DRA7: IVA, GPU, EVE in addition to the existing MPU domain. If
we do not do this, kernel configuring just the frequency using the
default boot loader configured voltage can fail on many corner lot
units and has been hard to debug. This specifically is a concern with
DRA7 generation of SoCs since other than VDD_MPU, all other domains
are only permitted to setup the voltages to required OPP only at boot.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Since we setup the voltage and frequency for the MM domain, we *must*
setup the ABB configuration needed for the domain as well. If we do not
do this, kernel configuring just the frequency using the default boot
loader configured voltage can fail on many corner lot units.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
ABB TX_DONE mask will vary depending on ABB module. For example,
3630 never had ABB on IVA domain, while OMAP5 does use ABB on MM domain,
DRA7 has it on all domains with the exception of CORE, RTC.
Hence, move the txdone mask definition over to structure describing
voltage domain.
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
This information is already available under vcores->volts.efuse.reg.
There is no reason for duplicating the information since AVS Class 0
definitions are common for OMAP5 and DRA7 and defined with
STD_FUSE_OPP_* macros. This allows a central location of defining
the ABB and voltage definitions especially since they are reused.
This also makes it simpler to prevent mistakes involved when changing
the boot OPP for the device.
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
do_set_iodelay can now be used from board files based on needs of the
platforms variation they have.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Since many platforms may need different pad configuration required
depending on variation of the platform with minor deltas, it is
easier to maintain a sub step based approach to allow for pin mux
and iodelay configuration which may depend on the platform variations
and need to be done in IO isolation.
While we retain the older __recalibrate_iodelay function which provides
a ready sequencing, __recalibrate_iodelay_start and
__recalibrate_iodelay_end may be alternatively used now and the callers
will be responsible for the correct sequencing of operations.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Based on data from EMIF configuration tool 1.1.1.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Based on data from EMIF configuration tool 1.1.1. Expected update for
CTRL_WKUP_EMIF1_SDRAM_CONFIG_EXT in the next revision of the tool has
been incorporated as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Add support for detection of SR2.0 version of DRA72x family of
processors.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The newer versions of DRA7 boards has EEPROM populated with DDR
size specified in it. Moving DRA7 specific emif related settings
to board files so that emif settings can be identified based on EEPROM.
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Enable EEPROM support for DRA74-evm.
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Read and write leveling can be enabled independently. Check for these
enable bits before updating the read and write leveling output values.
This will allow to use the combination of software and hardware leveling.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Current AM57xx evm supports both BeagleBoard-X15
(http://beagleboard.org/x15) and AM57xx EVM
(http://www.ti.com/tool/tmdxevm5728).
The AM572x EValuation Module(EVM) provides an affordable platform to
quickly start evaluation of Sitara. ARM Cortex-A15 AM57x Processors
(AM5728, AM5726, AM5718, AM5716) and accelerate development for HMI,
machine vision, networking, medical imaging and many other industrial
applications. This EVM is based on the same BeagleBoard-X15 Chassis
and adds mPCIe, mSATA, LCD, touchscreen, Camera, push button and TI's
wlink8 offering.
Since the EEPROM contents are compatible between the BeagleBoard-X15 and
the AM57xx-evm, we add support for the detection logic to enable
support for various user programmable scripting capability.
NOTE: U-boot configuration is currently a superset of AM57xx evm and
BeagleBoard-X15 and no additional configuration tweaking is needed.
This change also sets up the stage for future support of TI AM57xx EVMs
to the same base bootloader build.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
BeagleBoard X15 (http://beagleboard.org/x15) support in u-boot does
actually support two different platform configuration offered by
TI. In addition to BeagleBoard X15, it also supports the TMDXEVM5728
(or more commonly known as AM5728-evm).
Information about the TI AM57xx EVM can be found here
http://www.ti.com/tool/tmdxevm5728
The EVM configuration is 1-1 compatible with BeagleBoard X15 with the
additional support for mPCIe, mSATA, LCD, touchscreen, Camera, push
button and TI's wlink8 offering.
Hence, we rename the beagle_x15 directory to am57xx to support TI
EVMs that use the AM57xx processor. By doing this we have common code
reuse. This sets the stage to have a common u-boot image solution for
multiple TI EVMs such as that already done for am335x and am437x. This
sets the stage for upcoming multiple TI EVMs that share the same code
base.
NOTE: Commit eae7ae185335 ("am437x: Add am57xx_evm_defconfig using
CONFIG_DM") introduced DT support for beagle_x15 under am57xx_evm
platform name. However, this ignored the potential confusion arising for
users as a result. To prevent this, existing beagle_x15_defconfig is
renamed as am57xx_evm_nodt_defconfig to denote that this is the "non
device tree" configuration for the same platform. We still retain
am57xx-beagle-x15.dts at this point, since we just require the common
minimum dts.
As a result of this change, users should expect changes in build
procedures('make am57xx_evm_nodt_defconfig' instead of 'make
beagle_x15_defconfig'). Hopefully, this would be a one-time change.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
This introduces omap5 support for omap_die_id, which matches the common
omap_die_id definition. It replaces board-specific code to grab the die id bits.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Now that we have separate function to enable USB clocks, remove
enabling USB clocks from enable_basic_clocks(). Now board_usb_init()
should take care to invoke enable_usb_clocks() for enabling
USB clocks.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Added functions to enable and disable USB clocks which can be invoked
during USB init and USB exit respectively.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Enabled clocks for the second dwc3 controller and second USB PHY present in
DRA7.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
DP83865 ethernet phy used on DRA74x-evm is quirky and the datasheet
provided IODELAY values for standard RGMII phys do not work.
Silicon Revision(SR) 2.0 provides an alternative bit configuration
that allows us to do a "gross adjustment" to launch the data off a
different internal clock edge. Manual IO Delay overrides are still
necessary to fine tune the clock-to-data delays. This is a necessary
workaround for the quirky ethernet Phy we have on the platform.
NOTE: SMA registers are spare "kitchen sink" registers that does
contain bits for other workaround as necessary as well. Hence the
control for the same is introduced in a generic SoC specific, board
generic location.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Add support for detection of ES2.0 version of DRA7 family of
processors. ES2.0 is an incremental revision with various fixes
including the following:
- reset logic fixes
- few assymetric aging logic fixes
- MMC clock rate fixes
- Ethernet speed fixes
- edma fixes for mcasp
[ravibabu@ti.com: posted internal for an older bootloader]
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Adds functions to enable and disable edma3 clocks which can be invoked
by drivers using edma3 to control the clocks.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
