| Age | Commit message (Collapse) | Author |
|---|
|
This patch makes chip_id() as a global routine so that
it can be used in other places as required.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch modifies the chip_id routine to get either idcode or
silicon version based on the argument received.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
TCM on ZynqMP needs to be intialized in a sequence
and this patch provides a global routine to perform
this as per requirement.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
If PMUFW version is not v0.3 then panic.
ZynqMP switch to CCF based clock driver which requires
PMUFW to be present at certain version.
This patch ensure that you use correct and tested PMUFW
binary.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Define routines of mmio write and read functionalities
for zynqmp platform.
Also do not call SMC from SPL because SPL is running before ATF in EL3
that's why SMCs can't be called because there is nothing to call.
zynqmp_mmio*() are doing direct read/write accesses and this patch does
the same. PMUFW is up and running at this time and there is a way to talk
to pmufw via IPI but there is no reason to implement IPI stuff in SPL if
we need just simple read for getting clock driver to work.
Also make invoke_smc as global so that it can be reused in
multile places where ever possible.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
If available use the clock framework to set the tx clock rate of the
zynq ethernet controller.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Xilinx ATF extending options for passing images from BL2(FSBL)
to BL31. U-Boot SPL is FSBL replacement that's why it should generate
handoff structure the same. Support only one entry which is U-Boot in
EL2 itself. When FIT image is adopted structure generate should be data
driven.
Currently ATF is placing this structure at the beggining of OCM which is
rewriting early parts of ATF which should be unused at that time.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Enable and use the clock driver routine
defined in clock driver toset required
clock appropriately.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Support RAM and MMC boot mode in SPL also with SPL_FIT images.
In MMC boot mode two boot options are available:
1) Boot flow with ATF(EL3) and full U-Boot(EL2):
aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin
mkimage -A arm64 -O linux -T kernel -C none -a 0xfffe5000 -e 0xfffe5000
-d bl31.bin atf.ub
cp spl/boot.bin <sdcard fat partition>
cp atf.ub <sdcard fat partition>
cp u-boot.bin <sdcard fat partition>
2) Boot flow with full U-Boot(EL3):
cp spl/boot.bin <sdcard>
cp u-boot*.img <sdcard>
3) emmc boot mode
dd if=/dev/zero of=sd.img bs=1024 count=1024
parted sd.img mktable msdos
parted sd.img mkpart p fat32 0% 100%
kpartx -a sd.img
mkfs.vfat /dev/mapper/loop0p1
mount /dev/mapper/loop0p1 /mnt/
cp spl/boot.bin /mnt
cp u-boot.img /mnt
cp u-boot.bin /mnt
cp atf.ub /mnt
umount /dev/mapper/loop0p1
kpartx -d sd.img
cp sd.img /tftpboot/
and program it via u-boot
tftpb 10000 sd.img
mmcinfo
mmc write 10000 0 $filesize
mmc rescan
mmc part
ls mmc 0
psu_init() function contains low level SoC setup generated for every HW
design by Xilinx design tools. xil_io.h is only supporting file to fix
all dependencies from tools. The same solution was used on Xilinx Zynq.
The patch also change CONFIG_SYS_INIT_SP_ADDR to the end of OCM which
stays at the same location all the time.
Bootrom expects starting address to be at 0xfffc0000 that's why this
address is SPL_TEXT_BASE.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Move driver to DM
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch fix compilation error:
drivers/mmc/zynq_sdhci.c:16:5: error: conflicting types for
‘zynq_sdhci_init’
int zynq_sdhci_init(phys_addr_t regbase)
^
In file included from drivers/mmc/zynq_sdhci.c:14:0:
./arch/arm/include/asm/arch/sys_proto.h:16:5: note: previous declaration
of ‘zynq_sdhci_init’ was here
int zynq_sdhci_init(unsigned long regbase);
^
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Wire up ethernet controllers and enable MII and BOOTP options.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
SLCR can be used for IP configuration setting.
Add SLCR skeleton to enable run time checking.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add basic Xilinx ZynqMP arm64 support.
Serial and SD is supported.
It supports emulation platfrom ep108 and QEMU.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
