summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2015-10-30Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
2015-10-29arm: ls1021a: Add sata support on qds and twr boardtang yuantian
Freescale ARM-based Layerscape LS102xA contain a SATA controller which comply with the serial ATA 3.0 specification and the AHCI 1.3 specification. This patch adds SATA feature on ls1021aqds and ls1021atwr boards. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8/ls1043a: Enable secondary coresHou Zhiqiang
After the secondary cores enter U-Boot, use CONFIG_ARMV8_MULTIENTRY to make secondary cores excute in spin loop. Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8/ls1043ardb: esdhc: Add esdhc support for ls1043ardbYangbo Lu
This patch adds esdhc support for ls1043ardb. Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8/ls1043a: Add Fman supportShaohui Xie
Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8/ls1043ardb: Add nand boot supportGong Qianyu
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8/ls1043ardb: Add LS1043ARDB board supportMingkai Hu
LS1043ARDB Specification: ------------------------- Memory subsystem: * 2GByte DDR4 SDRAM (32bit bus) * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 16 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * XFI 10G port * QSGMII with 4x 1G ports * Two RGMII ports PCIe: * PCIe2 (Lanes C) to mini-PCIe slot * PCIe3 (Lanes D) to PCIe slot USB 3.0: two super speed USB 3.0 type A ports UART: supports two UARTs up to 115200 bps for console Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
2015-10-29armv8/fsl_lsch2: Add fsl_lsch2 SoCMingkai Hu
Freescale LayerScape with Chassis Generation 2 is a set of SoCs with ARMv8 cores and 2rd generation of Chassis. Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8/fsl_lsch3: Change arch to fsl-layerscapeMingkai Hu
There are two LS series processors are built on ARMv8 Layersacpe architecture currently, LS2085A and LS1043A. They are based on ARMv8 core although use different chassis, so create fsl-layerscape to refactor the common code for the LS series processors which also paves the way for adding LS1043A platform. Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv7/ls1021a: move ns_access to common fileMingkai Hu
Config Security Level Register is different between different SoCs, so put the CSL register definition into the arch specific directory. Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29arm: ls102xa: enable snooping for CAAM transactionshoria.geanta@freescale.com
Enable snooping for CAAM read & write transactions by programming the SCFG snoop configuration register: SCFG_SNPCNFGCR[SECRDSNP] SCFG_SNPCNFGCR[SECWRSNP] Signed-off-by: Horia Geantă <horia.geanta@freescale.com> Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29Data types defined for 64 bit physical addressAneesh Bansal
Data types and I/O functions have been defined for 64 bit physical addresses in arm. Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29ls102xa: fdt: Disable IFC in SD boot for QSPIAlison Wang
As QSPI/DSPI and IFC are pin multiplexed, IFC is disabled in SD boot for QSPI. This patch will add fdt support for this rule. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-26armv8/fsl-lsch3: fdt: Check the pointer returned from call to a function may ↵Alison Wang
be NULL Pointer 'reg' returned from call to function 'fdt_getprop' may be NULL, will be passed to function and may be dereferenced there by passing argument 1 to function 'of_read_number'. So check pointer 'reg' first. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-25dts: zed: Enable zynq qspi controller nodeJagan Teki
Enabled zynq qspi controller node for zed board. Signed-off-by: Jagan Teki <jteki@openedev.com> Cc: Simon Glass <sjg@chromium.org> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com>
2015-10-25dts: zc770-xm010: Enable zynq qspi controller nodeJagan Teki
Enabled zynq qspi controller node for zc770-xm010 board. => sf probe 0 -- bus1 for selecting qspi controller => sf probe 1 -- bus0 for selecting spi controller Signed-off-by: Jagan Teki <jteki@openedev.com> Cc: Simon Glass <sjg@chromium.org> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com>
2015-10-25dts: zc706: Enable zynq qspi controller nodeJagan Teki
Enabled zynq qspi controller node for zc706 board. Signed-off-by: Jagan Teki <jteki@openedev.com> Cc: Simon Glass <sjg@chromium.org> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com>
2015-10-25dts: zc702: Enable zynq qspi controller nodeJagan Teki
Enabled zynq qspi controller node for zc702 board. Signed-off-by: Jagan Teki <jteki@openedev.com> Cc: Simon Glass <sjg@chromium.org> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com>
2015-10-25dts: microzed: Enable zynq qspi controller nodeJagan Teki
Enabled zynq qspi controller node for microzed board, verified the same on spansion spi-nor flash. Signed-off-by: Jagan Teki <jteki@openedev.com> Cc: Simon Glass <sjg@chromium.org> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Jagan Teki <jteki@openedev.com>
2015-10-25dts: zynq: Add zynq qspi controller nodesJagan Teki
This patch adds zynq qspi controller nodes in zynq-7000.dtsi. Signed-off-by: Jagan Teki <jteki@openedev.com> Cc: Simon Glass <sjg@chromium.org> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Jagan Teki <jteki@openedev.com>
2015-10-24arm, powerpc: select SYS_GENERIC_BOARDMasahiro Yamada
We have finished Generic Board conversion for ARM and PowerPC, i.e. all the boards have been converted except OpenRISC, SuperH, SPARC, which have not supported Generic Board framework yet. Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro defines in include/configs/*.h. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-10-24zynq: Move SPL console init out of board_init_f()Simon Glass
We should not init the console this early since it precludes using driver model for the UART, since it is not set up at the start of board_init_f(). See the README for more information. The debug UART does not have this restriction. If we want to do early init with the console on it can be done in spl_board_init(). Move the preloader_console_init() call from board_init_f() to board_init_r(). Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Michal Simek <michal.simek@xilinx.com>
2015-10-24arm: Switch 32-bit ARM to using generic global_data setupSimon Glass
There is quite a bit of assembler code that can be removed if we use the generic global_data setup. Less arch-specific code makes it easier to add new features and maintain the start-up code. Drop the unneeded code and adjust the hooks in board_f.c to cope. Signed-off-by: Simon Glass <sjg@chromium.org>
2015-10-24arm: Switch aarch64 to using generic global_data setupSimon Glass
There is quite a bit of assembler code that can be removed if we use the generic global_data setup. Less arch-specific code makes it easier to add new features and maintain the start-up code. Drop the unneeded code and adjust the hooks in board_f.c to cope. Tested on LS2085ARDB and LS2085AQDS (armv8 SoC). Tested-by: York Sun <yorksun@freescale.com> Signed-off-by: Simon Glass <sjg@chromium.org>
2015-10-22am437x: Add am57xx_evm_defconfig using CONFIG_DMMugunthan V N
Import various DT files for am57xx-beagle-x15 from Linux Kernel v4.2 Add config file for this board, enable DM, DM_GPIO, DM_SERIAL and DM_MMC. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-10-22am437x: Add am437x_sk_evm_defconfig using CONFIG_DMMugunthan V N
Import various DT files for am437x-sk-evm from Linux Kernel v4.2 Add config file for this board, enable DM, DM_GPIO, DM_SERIAL and DM_MMC. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22am437x: Add am437x_gp_evm_defconfig using CONFIG_DMMugunthan V N
Import various DT files for am4372, an43xx pinctrl and am437x-gp-evm from Linux Kernel v4.2 Add config file for this board, enable DM, DM_GPIO, DM_SERIAL and DM_MMC. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22omap_hsmmc: update struct hsmmc to accomodate base address from DTMugunthan V N
Existing driver gets the actual omap hammc base address + 0x100 bytes as the first 0x100 bytes is not used by the driver. But with DM conversion the base address from DT is different, to accommodate the offset adding res0[0x100] to struct hsmmc. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22dra7xx: Add dra74_evm_defconfig using CONFIG_DMMugunthan V N
Import various DT files for dra7-evm from Linux Kernel v4.2 Add config file for this board, enable DM and DM_GPIO Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22ARM: dts: k2g: Add DT supportLokesh Vutla
Add basic DT support for k2g evm. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: add SD card and eMMC supportRoger Quadros
Add MMC support for k2g Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-10-22driver: net: keystone_net: add support for rgmii phyVitaly Andrianov
In K2G, Ethernet doesn't support SGMII instead it support RGMII, adding support to the driver to connect to RGMII phy. Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22driver: net: keystone_net: fix phy mode configurationMugunthan V N
Phy mode is a board property and it can be different between multiple board and ports, so it should not be hardcoded in driver to one specific mode. So adding a field in eth_priv_t structure to pass phy mode to driver. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: update keystone nav rx queue numbersVitaly Andrianov
update K2G nav rx queue number Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: Correct base addressesVitaly Andrianov
Coreect base addresses for SPI, Queue Manager, Ethernet, GPIO, and MSMC segments. Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: Add support for pin mux configurationVitaly Andrianov
Add api for configuring pin mux. Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: Add ddr3 infoVitaly Andrianov
Add ddr3 related info Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: Add PSC infoVitaly Andrianov
Add psc information for k2g Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: Add clock informationVitaly Andrianov
Add clock information for Galileo Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-10-22ARM: k2g: Add pll dataVitaly Andrianov
Add pll data for k2g Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: Add kconfig supportLokesh Vutla
Add Kconfig support Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: Add support for CPU detectionLokesh Vutla
Adding CPU detection support for Keystone2 Galileo. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: keystone2: Use dtb images by defaultLokesh Vutla
Now that OF_CONTROL is enabled on all keystone2 platforms, build the default images with DT. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: dts: k2e: Enable OF_CONTROL and DMLokesh Vutla
Import k2e specific DT files from Linux Kernel and enable OF_CONTROL, DM, DM_SERIAL. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: dts: k2l: Enable OF_CONTROL and DMLokesh Vutla
Import k2l specific DT files from Linux Kernel and enable OF_CONTROL, DM, DM_SERIAL. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: dts: k2hk: Enable OF_CONTROL and DMLokesh Vutla
Import k2hk specific DT files from Linux Kernel and enable OF_CONTROL, DM, DM_SERIAL. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: dts: keystone2: Do not use LPAE addresses in U-BootLokesh Vutla
Keystone dts files assumes that LPAE is enabled and top level root node uses 64bit addresses. This breaks the keystone boot with CONFIG_OF_CONTROL enabled. So do not use 64 bit addresse in U-Boot DT. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: dts: Keystone2: Import generic dt files from Linux KernelLokesh Vutla
Import various generic dts files from Linux kernel so that all keystone2 platforms can be DT in U-boot. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: keystone2: Fix serial port initLokesh Vutla
With CONFIG_DM_SERIAL is enabled NS16550_init() cannot be called directly. Driver probe should be taking care of this. So call this function only when DM_SERIAL is not enabled. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22omap-common: Common get_board_serial function to pass serial through ATAGPaul Kocialkowski
Since there is a common function to grab the serial number from the die id bits, it makes sense have one to parse that serial number and feed it to the serial ATAG. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
generated by cgit v0.10.2 at 2024-09-02 23:11:05 (GMT)