summaryrefslogtreecommitdiff
path: root/arch/mips/Kconfig
AgeCommit message (Collapse)Author
2016-09-21boston: Introduce support for the MIPS Boston development boardPaul Burton
This patch introduces support for building U-Boot to run on the MIPS Boston development board. This is a board built around an FPGA & an Intel EG20T Platform Controller Hub, used largely as part of the development of new CPUs and their software support. It is essentially the successor to the older MIPS Malta board. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-09-21MIPS: Malta: Enable CM & L2 supportPaul Burton
Enable support for the MIPS Coherence Manager & L2 caches on the MIPS Malta board, removing the need for us to attempt to bypass the L2 during boot (which would fail with recent CPUs that expose L2 config via the CM anyway). Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-09-21MIPS: L2 cache supportPaul Burton
This patch adds support for initialising & maintaining L2 caches on MIPS systems. The L2 cache configuration may be advertised through either coprocessor 0 or the MIPS Coherence Manager depending upon the system, and support for both is included. If the L2 can be bypassed then we bypass it early in boot & initialise the L1 caches first, such that we can start making use of the L1 instruction cache as early as possible. Otherwise we initialise the L2 first such that the L1s have no opportunity to generate access to the uninitialised L2. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-09-21MIPS: Map CM Global Control RegistersPaul Burton
Map the Global Control Registers (GCRs) provided by the MIPS Coherence Manager (CM) in preparation for using some of them in later patches. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-09-21mips: Add MIPSfpga platform supportZubair Lutfullah Kakakhel
MIPSfpga is an FPGA based dev platform. In a nutshell, its a microAptiv cpu core with lots of Xilinx IP blocks The FPGA dev board used is the Nexys4DDR board by Digilent. For more information, check the Readme file in board/imgtec/xilfpga Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com> Reviewed-by: Paul Burton <paul.burton@imgtec.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-06-10MIPS: Make CONFIG_SYS_DCACHE_LINE_SIZE int, not hexPaul Burton
For consistency with the other cache-related Kconfig entries & the values actually set by boards, make CONFIG_SYS_DCACHE_LINE_SIZE an int entry instead of a hex entry. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Fixes: 372286217f05 ("MIPS: Split I & D cache line size config")
2016-05-31MIPS: Split I & D cache line size configPaul Burton
Allow L1 Icache & L1 Dcache line size to be specified separately, since there's no architectural mandate that they be the same. The [id]cache_line_size functions are tidied up to take advantage of the fact that the Kconfig entries are always present to simply check them for zero rather than needing to #ifdef on their presence. Signed-off-by: Paul Burton <paul.burton@imgtec.com> [removed CONFIG_SYS_CACHELINE_SIZE in include/configs/pic32mzdask.h] Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-05-31MIPS: Move cache sizes to KconfigPaul Burton
Move details of the L1 cache line sizes & total sizes into Kconfig, defaulting to 0. A new CONFIG_SYS_CACHE_SIZE_AUTO Kconfig entry is introduced to allow platforms to select auto-detection of cache sizes, and it defaults to being enabled if none of the cache sizes are set by the configuration (ie. sizes are all the default 0), and code is adjusted to #ifdef on that rather than on the definition of the sizes (which will always be defined even if 0). Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-05-31MIPS: add tune for MIPS 34kcDaniel Schwierzeck
Add tune Kconfig option for MIPS 34kc. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-05-31malta: Allow MIPS64 buildsPaul Burton
Both real Malta boards & emulators that mimic Malta (eg. QEMU) can support MIPS64 CPUs. Allow MIPS64 builds of U-Boot for such boards, which enables the user to make use of the whole 64 bit address space. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-05-25malta: Use device model & tree for UARTPaul Burton
Make use of device model & device tree to probe the UART driver. This is the initial step in bringing Malta up to date with driver model, and allows for cleaner handling of the different I/O addresses for different system controllers by specifying the ISA bus address instead of a translated memory address. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-05-20malta: Support MIPS32r6 configurationsPaul Burton
Both real Malta boards & QEMU's Malta emulation can feature MIPS32r6 CPUs. Allow building U-Boot for such systems by selecting CONFIG_SUPPORTS_CPU_MIPS32_R6 for Malta. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-05-20MIPS: Support for targetting MIPSr6Paul Burton
Add support for targetting MIPS32r6 & MIPS64r6 systems, in the same way that we currently select release 1 or release 2 targets. MIPSr6 is not entirely backwards compatible with earlier releases of the architecture. Some instructions are encoded differently, some are removed, some are reused, so it is not practical to run U-Boot built for earlier revisions on a MIPSr6 system. Update their Kconfig help text to reflect that. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-05-20MIPS: Simplify CONFIG_SYS_CPU valuesPaul Burton
Rather than having the values for CONFIG_SYS_CPU depend upon each architecture revision, have them depend upon the more general CONFIG_CPU_MIPS32 & CONFIG_CPU_MIPS64 which in turn depend upon the architecture revisions. This is done in preparation for adding MIPSr6 support, which would otherwise need to introduce new cases here. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-05-20mips: Add MIPS 74Kc tuneMarek Vasut
Add MIPS 74Kc tune Kconfig option. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Wills Wang <wills.wang@live.com> [added missing tune-y entry in arch/mips/Makefile] Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-05-20mips: add base support for QCA/Atheros ath79 SOCsWills Wang
This patch add some common code for QCA/Atheros ath79 SOCs such as DDR tuning, chip reset and CPU detection. Signed-off-by: Wills Wang <wills.wang@live.com>
2016-05-06Fix various typos, scattered over the code.Robert P. J. Day
Spelling corrections for (among other things): * environment * override * variable * ftd (should be "fdt", for flattened device tree) * embedded * FTDI * emulation * controller
2016-02-01MIPS: initial infrastructure for Microchip PIC32 architecturePurna Chandra Mandal
Create initial directory, Kconfigs needed for PIC32 architecture support. Also add PIC32 specific register definition required for drivers. Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-01MIPS: Support dynamic I/O port base addressPaul Burton
The existing mips_io_port_base variable isn't suitable for use early during boot since it will be stored in the .data section which may not be writable pre-relocation. Fix this by moving the I/O port base address into struct arch_global_data. In order to avoid adding this field for all targets, make this dependant upon a new Kconfig entry CONFIG_DYNAMIC_IO_PORT_BASE. Malta is the only board which sets a non-zero I/O port base, so select this option only for Malta. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-01-16MIPS: kconfig: add option for MIPS_L1_CACHE_SHIFTDaniel Schwierzeck
Add Kconfig symbol for L1 cache shift like the kernel does. The value of CONFIG_SYS_CACHELINE_SIZE is not a reliable source for ARCH_DMA_MINALIGN anymore, because it is optional on MIPS. If CONFIG_SYS_CACHELINE_SIZE is not defined by a board, the cache sizes are automatically detected and ARCH_DMA_MINALIGN would be set to 128 Bytes. The default value for CONFIG_MIPS_L1_CACHE_SHIFT is 5 which corresponds to 32 Bytes. All current MIPS boards already used that value. While on it, fix the Malta board to use a value of 6 like the kernel port does. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-01-16MIPS: Kconfig: optimize gcc -march and -mtune setupDaniel Schwierzeck
Move setup of -march to arch/mips/Makefile and follow the design on ARM. Also add a possibility to chose specific CPU tune options. Signed-off-by: Wills Wang <wills.wang@live.com> Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-06-26Move default y configs out of arch/board KconfigJoe Hershberger
Some archs/boards specify their own default by pre-defining the config which causes the Kconfig system to mix up the order of the configs in the defconfigs... This will cause merge pain if allowed to proliferate. Remove the configs that behave this way from the archs. A few configs still remain, but that is because they only exist as defaults and do not have a proper Kconfig entry. Those appear to be: SPIFLASH DISPLAY_BOARDINFO Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates, drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM] Signed-off-by: Tom Rini <trini@konsulko.com>
2015-05-12arch: Make board selection choices optionalJoe Hershberger
By making the board selections optional, every defconfig will include the board selection when running savedefconfig so if a new board is added to the top of the list of choices the former top's defconfig will still be correct. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Cc: Tom Rini <trini@konsulko.com>
2015-04-24MIPS: implement device-tree handover to Linux kernelDaniel Schwierzeck
Add device-tree handover to Linux kernel conforming with MIPS UHI [1]. Register $a0 will be set to the reserved value -2. The address of the device-tree blob will be stored as KSEG0 address in $a1. $a2 and $a3 are set to zero. [1] http://prplfoundation.org/wiki/MIPS_documentation Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29MIPS: allow systems to skip loads during cache initPaul Burton
Current MIPS systems do not require that loads be performed to force the parity of cache lines, a simple invalidate by clearing the tag for each line will suffice. Thus this patch makes the loads & subsequent second invalidation conditional upon the CONFIG_SYS_MIPS_CACHE_INIT_RAM_LOAD option, and defines that for existing mips32 targets. Exceptions are malta where this is known to be unnecessary, and qemu-mips where caches are not implemented. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-21MIPS: add Kconfig option for CONFIG_SWAP_IO_SPACEDaniel Schwierzeck
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-21MIPS: replace $(CPU) with Kconfig symbolsDaniel Schwierzeck
Conditionally set head-y and lib-y with boolean Kconfig symbols for selected CPU. This deprecates the usage of the $(CPU) variable. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-21MIPS: bootm: prepare a flattened device tree for the kernelDaniel Schwierzeck
Add the initial code to prepare a flattened device tree for the kernel like relocating the FDT blob and fixing up the /chosen and /memory nodes. The final hand over to the kernel is not yet implemented. After the community agreed on the MIPS boot interface for device trees, the corresponding code will be added. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-21MIPS: bootm: refactor preparation of Linux kernel environmentDaniel Schwierzeck
Move preparation of Linux kernel environment in a separate function and mark it as legacy. Add a Kconfig option to make that legacy mode configurable. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-21MIPS: bootm: refactor preparation of Linux kernel command lineDaniel Schwierzeck
Move preparation of Linux kernel command line in a separate function and mark it as legacy. Add a Kconfig option to make that legacy mode configurable. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01MIPS: kconfig: merge targets qemu_mips and qemu_mips64Daniel Schwierzeck
Now the user can separately select the CPU type. Thus the targets qemu_mips and qemu_mips64 can be merged to a single target. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01MIPS: kconfig: globally define CONFIG_SYS_CPU for MIPSDaniel Schwierzeck
Now the user can select the CPU type for each target. Thus CONFIG_SYS_CPU could be set globally. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01MIPS: kconfig: add options for CPU type selectDaniel Schwierzeck
Add new Kconfig option to let the user select the targets CPU type. Each target have to select SUPPORTS_CPU_MIPS[32,64]_R[1,2] to indicate which CPU types are supported. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01MIPS: kconfig: add options for endianess selectDaniel Schwierzeck
Add new Kconfig option to let the user select the targets endianess. Each target have to select SUPPORTS_BIG_ENDIAN and/or SUPPORTS_LITTLE_ENDIAN to indicate which endianess is supported. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-10-23mips: enable CONFIG_USE_PRIVATE_LIBGCC by defaultMasahiro Yamada
Without the private libgcc, we need a full multilib toolchain with different libgcc or multiple toolchains to build all BE/LE and hard-float/soft-float variants of MIPS boards. That is not feasible. This commit allows us to build all the MIPS boards with a single kernel.org toolchain: https://www.kernel.org/pub/tools/crosstool/files/bin/x86_64/4.9.0/ x86_64-gcc-4.9.0-nolibc_mips-linux.tar.xz This change sounds reasonable for most users. If necessary, you can disable this option via "make menuconfig" or friends. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-09-13kconfig: remove redundant "string" type in arch and board KconfigsMasahiro Yamada
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME} are specified in arch/Kconfig. We can delete the ones in arch and board Kconfig files. This commit can be easily reproduced by the following command: find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e ' /config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ { N s/\n[[:space:]]*string// } ' Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-07-30kconfig: add board Kconfig and defconfig filesMasahiro Yamada
This commit adds: - arch/${ARCH}/Kconfig provide a menu to select target boards - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig set CONFIG macros to the appropriate values for each board - configs/${TARGET_BOARD}_defconfig default setting of each board (This commit was automatically generated by a conversion script based on boards.cfg) In Linux Kernel, defconfig files are located under arch/${ARCH}/configs/ directory. It works in Linux Kernel since ARCH is always given from the command line for cross compile. But in U-Boot, ARCH is not given from the command line. Which means we cannot know ARCH until the board configuration is done. That is why all the "*_defconfig" files should be gathered into a single directory ./configs/. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
generated by cgit v0.10.2 at 2024-08-03 22:43:43 (GMT)