| Age | Commit message (Collapse) | Author |
|---|
|
Azalia configuration may be different across boards, hence it's not
appropriate to do that in the SoC level. Instead, let's make the
SoC update_fsp_azalia_configs() routine as a weak version, and do
the actual work in the board codes.
So far it seems only som-db5800-som-6867 board enables the Azalia.
Move the original codes into som-db5800-som-6867.c.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
At present we directly pass the Azalia config pointer to the FSP UPD.
This updates to use a function to do the stuff, like Braswell does.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
So far there are two copies of Azalia struct defines with one in
baytrail and the other one in braswell. This consolidates these
two into one, put it in the common place, and remove the prefix
pch_ to these structs to make their names more generic.
This also corrects reset_wait_timer from us to ms.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
It was observed that when booting a Ubuntu 16.04 kernel, doing ACPI
S3 suspend/resume sometimes causes the Ubuntu kernel hang forever.
The issue is however not reproduced with a kernel built from i386/
x86_64 defconfig configuration.
The unstability is actually caused by unexpected interrupts being
generated during the S3 resume. For some unknown reason, FSP (gold4)
for BayTrail configures the GPIO DFX5 PAD to enable level interrupt
(bit 24 and 25). As this pin keeps generating interrupts during an
S3 resume, and there is no IRQ requester in the kernel to handle it,
the kernel seems to hang and does not continue resuming.
Clear the mysterious interrupt bits for this pin.
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
It was noticed a few times, that the reboot from Linux (reboot command)
is different from the reboot (reset command) under U-Boot. The U-Boot
version does seem to reset the board more deeply (PCI cards etc) than
the Linux reboot.
This is actually caused by missing full reset bit in the reset register
value in the ACPI FADT table.
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
|
|
CPU_INTEL_TURBO_NOT_PACKAGE_SCOPED must be turned on for Baytrail.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present we support multiple environment drivers but there is not way to
select between them at run time. Also settings related to the position and
size of the environment area are global (i.e. apply to all locations).
Until these limitations are removed we cannot really support more than one
environment location. Adjust the location to be a choice so that only one
can be selected. By default the environment is 'nowhere', meaning that the
environment exists only in memory and cannot be saved.
Also expand the help for the 'nowhere' option and move it to the top since
it is the default.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Move all of the imply logic to default X if Y so it works again]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
After MMC is converted to DM, convert to use DM SCSI as well for all
x86 boards and imply BLK for both MMC and SCSI drivers.
CONFIG_SCSI_DEV_LIST is no longer used. Clean them up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Convert the pci_mmc driver over to driver model and migrate all x86 boards
that use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove DM_MMC from edison_defconfig]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This converts Intel ICH6 GPIO driver to Kconfig, and add it to the
imply list of platform drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Like other peripheral drivers, move USB related drivers to platform
Kconfig as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
BayTrail integrates lots of peripherals that have U-Boot drivers.
Imply those in the platform Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Platform knows whether MRC cache is implemented, but using it can
be a choice of a specific board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
arch_misc_init() is intended to do architecture-dependent stuff.
This is required by each platform.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Intel Management Engine is required by the platform, however it's
not a must have when building a U-Boot image. For example, during
development normally programming ME firmware is a one-time effort.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
In Baytrail and Quark support code acpi_fill_madt() is identical.
Deduplicate its implementation by moving to lib/acpi_tables.c.
At the same time mark acpi_fill_madt() with __weak attribute to keep a
possibility to override it in platform code
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_SPI_FLASH
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This reverts commit ddb3ac3c716f56cead695444e65a7ba7b0946555.
With MMC converted to driver model, SCSI driver is broken due to
zero address access at (ops->read) in block_dread() function.
The fix (SCSI driver converted to DM) is ready in u-boot-dm branch,
but it is too late for this relese to get that in.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
It was observed that when -DDEBUG is used to generate a debug build,
U-Boot does not boot on MinnowMax board. A workaround is to disable
CONFIG_DEBUG_UART. The real issue is that in order to have the debug
uart to work, BayTrail SoC needs to be configured so that its internal
uart is available to be used as the debug uart.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
At present lpe/lpss-sio/scc FSP properties are all boolean, but in
fact for "enable-lpe" it has 3 possible options. This adds macros
for these options and change the property from a boolean type to
an integer type, and change their names to explicitly indicate what
the property is really for.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Introduce various meaningful macros for FSP settings and switch over
to use them instead of magic numbers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
"serial-debug-port-address" and "serial-debug-port-type" settings
are actually reserved in the FSP UPD data structure. Remove them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The default value of "fsp,mrc-init-tseg-size" should be 1 (1MB) per
FSP default settings. 0 is not valid.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Convert the pci_mmc driver over to driver model and migrate all x86 boards
that use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This adds APIs for determining previous sleep state from ACPI I/O
registers, as well as clearing sleep state on BayTrail SoC.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Stefan Roese <sr@denx.de>
|
|
The CPU udevice already has a few callbacks to retreive information
about the currently running CPUs. This patch adds a new get_vendor()
call that returns the vendor of the main CPUs.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
With this addition, the eMMC device available on the congatec and DFI
BayTrail SoM is detected correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
arch_cpu_init() can be simpler by this refactoring.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
To support the BayTrail internal SIO HS UART, the internal UART clock
needs to get configured. This patch adds support for this clock
configuration which will be done, if the PCI device(s) are found.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This introduces baytrail-specific ACPI global NVS structure, defined in
both C header file and ASL file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
There are quite a number of BayTrail boards that uses an external
SuperIO chipset to provide the legacy UART. For such cases, it's
better to have a Kconfig option to enable the internal UART.
So far BayleyBay and MinnowMax boards are using internal UART as
the U-Boot console, enable this on these two boards.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
So far this is hardcoded to 2, but it should really be read
from the I/O APIC register.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Instead of asking each platform to provide reserve_arch(),
supply it in arch/x86/cpu/cpu.c in a unified way.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
FADT/MADT tables are platform specific. Generate them for BayTrail.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch adds a parameter to the function setup_early_uart() to either
enable or disable the internal BayTrail legacy UART. Since the name
setup_early_uart() does not match its functionality any more, lets
rename it to setup_internal_uart() as well in this patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
At present interrupt routing is set up from arch_misc_init(). We can do it
a little later instead, in interrupt_init().
This removes the manual pirq_init() call. Where the platform does not have
an interrupt router defined in its device tree, no error is generated. Some
platforms do not have this.
Drop pirq_init() since it is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
|
|
fsp_init() runtime buffer parameter might be different across
different platforms. Move this to update_fsp_configs().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
|
|
To support platform-specific configurations (might not always be
UPD on some platform), use a better name update_fsp_configs() and
accepct struct fsp_config_data as its parameter so that platform
codes can handle whatever configuration data for that FSP.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
|
|
At present pci_mmc_init() does not correctly use the PCI function since the
list it passes is not terminated. The array size passed to pci_mmc_init() is
actually not used correctly. Fix this and adjust the pci_mmc_init() to scan
all available MMC devices.
Adjust this code to use the new driver model PCI API.
This should move over to the new MMC uclass at some point.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Convert all x86 boards to use driver model tsc timer.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
With MRC cache enabled, when typing 'reset' in the U-Boot shell,
BayTrail FSP initialization hangs at "Configuring Memory Start":
Setting BootMode to 0
Install PPI: 1F4C6F90-B06B-48D8-A201-BAE5F1CD7D56
Register PPI Notify: F894643D-C449-42D1-8EA8-85BDD8C65BDE
About to call MrcInit();
BayleyBay Platform Type
CurrentMrcData.BootMode = 4
Taking Fastboot path!
Configuring Memory Start...
Changing reset_cpu() to do a full system reset fixes this issue.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Save MRC cache to SPI flash in arch_misc_init().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
It turns out that calling fsp_init_phase_pci() in arch_misc_init()
is subject to break pci device drivers as with driver model, when
the bus enumeration happens is not deterministic.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
We should not fiddle with interrupts or the FSP when running as an EFI
payload. Detect this and skip this code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
We should signal to the FSP that PCI enumeration is complete. Perform this
task in a suitable place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This function can fail. In this case we should return the error rather than
swallowing it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Allow for configuration of FSP UPD from the device tree which will
override any settings which the FSP was built with itself.
Modify the MinnowMax and BayleyBay boards to transfer sensible UPD
settings from the Intel FSPv4 Gold release to the respective dts files,
with the condition that the memory-down parameters for MinnowMax are
also used.
Signed-off-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Removed fsp,mrc-debug-msg and fsp,enable-xhci for minnowmax, bayleybay
Fixed lines >80col
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Disable a few things which interfere with the EFI init. This allows the
Minnowboard MAX to boot into EFI, load a U-Boot payload then boot to the
U-Boot prompt.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add PCI IRQ routing information in the board device tree and enable
writing PIRQ routing table and MP table.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
