summaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2013-11-27imx-common: remove extraneous semicolon from macroEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-11-13i.MX6DQ/DLS: whitespace: Align IOMUX_PAD column in declarationsEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-11-13i.MX6DQ/DLS: remove unused pad declarationsEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-11-13i.MX6DQ: Add Pinmux settings that are present in mainline and Dual-Lite/SoloEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-11-13i.MX6DQ/DLS: remove useless mux/pad declarationsEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-11-13i.MX6DQ/DLS: replace pad names with their Linux kernel equivalentsEric Nelson
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-11-11arm, am33x: make RTC32K OSC enable configurableHeiko Schocher
As http://www.denx.de/wiki/view/U-Boot/DesignPrinciples#2_Keep_it_Fast states: "Initialize devices only when they are needed within U-Boot" enable the RTC32K OSC only, if CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is enabled. Enable this in ti_am335x_common.h, so all boards in mainline should work as before. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
2013-11-09Merge branch 'iu-boot/master' into 'u-boot-arm/master'Albert ARIBAUD
Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h
2013-11-08include: delete include/linux/config.hMasahiro Yamada
Linux Kernel abolished include/linux/config.h long time ago. (around version v2.6.18..v2.6.19) We don't need to provide Linux copatibility any more. This commit deletes include/linux/config.h and fixes source files not to include this. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-08cosmetic: remove empty lines at the top of fileMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-08sparc: include config.h to start.SMasahiro Yamada
arch/sparc/cpu/leon3/start.S requires CONFIG_SYS_SPARC_NWINDOES to be defined: #ifndef CONFIG_SYS_SPARC_NWINDOWS #error Must define number of SPARC register windows, default is 8 #endif But it missed to include <config.h>, which always ended up in compile error. This commit fixes this problem. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Daniel Hellstrom <daniel@gaisler.com>
2013-11-07Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-11-05Merge branch 'u-boot-atmel/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-11-04at91: add defines for reset typeRoger Meier
Signed-off-by: Roger Meier <r.meier@siemens.com> Acked-by: Bo Shen <voice.shen@atmel.com> Reviewed-by: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-04arm: atmel: at91sam9n12ek: add usb host supportBo Shen
Add usb host support for at91sam9n12ek board. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-04ARM: versatile: convert to common timer codeRob Herring
Convert versatile to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04ARM: tegra: convert to common timer codeRob Herring
Convert tegra to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04ARM: socfpga: convert to common timer codeRob Herring
Convert socfpga to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04ARM: mx25: convert to common timer codeRob Herring
Convert mx25 to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04ARM: highbank: convert to common timer codeRob Herring
Convert highbank to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04sh: convert to common timer codeRob Herring
Convert sh to use the commmon timer code. Remove reset_timer and set_timer as they are unused on sh. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04config: remove platform CONFIG_SYS_HZ definition part 2/2Rob Herring
Remove platform CONFIG_SYS_HZ definition for configs a-z*. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04Merge branch 'master' of git://git.denx.de/u-boot-blackfinTom Rini
Easy to resolve conflict on the GPIO change. Conflicts: arch/blackfin/cpu/Makefile Signed-off-by: Tom Rini <trini@ti.com>
2013-11-04blackfin: Move machine specific gpio_port_t structure back to blackfin arch ↵Steven Miao
folder. The gpio register mappings are different among blackfin processors. Signed-off-by: Steven Miao <realmz6@gmail.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-11-04blackfin: fix a warning in arch/blackfin/cpu/cpu.cMasahiro Yamada
This commit fixes: cpu.c:107: warning: ‘noreturn’ function does return Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-11-01ARM: OMAP5: DDR3: Change io settingsSRICHARAN R
The change from 0x64656465 to 0x64646464 is to remove the weak pull enabled on DQS, nDQS lines. This pulls the differential signals in the same direction which is not intended. So disabling the weak pulls improves signal integrity. On the uEVM there are 4 DDR3 devices. The VREF for 2 of the devices is powered by the OMAP's VREF_CA_OUT pins. The VREF on the other 2 devices is powered by the OMAP's VREF_DQ_OUT pins. So the net effect here is that only half of the DDR3 devices were being supplied a VREF! This was clearly a mistake. The second change improves the robustness of the interface and was specifically seen to cure corruption observed at high temperatures on some boards. With the above two changes better memory stability was observed with extended temperature ranges around 100C. Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-11-01dra7xx_evm: Enabled UART-boot mode and add dra7xx_evm_uart3 buildMinal Shah
UART booting is supported on this SoC, but via UART3 rather than UART1. Because of this we must change the board to use UART3 for all console access (only one UART is exposed on this board and a slight HW mod is required to switch UARTs). Signed-off-by: Minal Shah <minal.shah@ti.com> [trini: Make apply to mainline, reword commit] Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01am335x: Enable CONFIG_OMAP_WATCHDOG supportTom Rini
There is a board-specific portion for calling watchdog enable itself, in main U-Boot. Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01am33xx, davinci: Create and use <asm/davinci_rtc.h>Tom Rini
Create a common header file for the RTC IP block that is shared between davinci and am33xx. Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01blackfin: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Sonic Zhang <sonic.zhang@analog.com>
2013-11-01m68k: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Jason Jin <Jason.jin@freescale.com>
2013-11-01x86: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Simon Glass <sjg@chromium.org>
2013-11-01nios2: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Thomas Chou <thomas@wytron.com.tw>
2013-11-01nds32: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Macpaul Lin <macpaul@gmail.com>
2013-10-31mips: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-10-31microblaze: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Michal Simek <michal.simek@xilinx.com>
2013-10-31openrisc: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
2013-10-31avr32: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Andreas Bießmann <andreas.devel@googlemail.com>
2013-10-31sh: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2013-10-31sparc: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Daniel Hellstrom <daniel@gaisler.com>
2013-10-31sh: Do not include start.o in lib$(CPU).oMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2013-10-31sparc: fix a link errorMasahiro Yamada
Before this commit, arch/sparc/lib/Makefile used both COBJS and COBJS-y. And it missed to add COBJS-y into OBJS. This means bootm.o was never compiled even if CONFIG_CMD_BOOTM=y Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Daniel Hellstrom <daniel@gaisler.com>
2013-10-31ARM: s5pc, exynos: move Samsung ARM SoC specific code under arch/arm/Masahiro Yamada
This patch moves S5PC, EXYNOS specific directory entries from the toplevel Makefile to arch/arm/cpu/armv7/Makefile using Kbuild descending feature. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2013-10-31ARM: omap: move OMAP specific code under arch/arm/Masahiro Yamada
This patch moves OMAP specific directory entries from the toplevel Makefile and spl/Makefile to arch/arm/cpu/armv7/Makefile using Kbuild descending feature. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Rini <trini@ti.com>
2013-10-31ARM: tegra: move Tegra specific code under arch/arm/Masahiro Yamada
This patch moves Tegra specific directory entries from the toplevel Makefile and spl/Makefile to arch/arm/cpu/*/Makefile using Kbuild descending feature. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Warren <TWarren@nvidia.com>
2013-10-31powerpc: convert makefiles to Kbuild styleMasahiro Yamada
Note: arch/powerpc/cpu/mpc8260/Makefile is originally like follows: ---<snip>--- START = start.o kgdb.o COBJS = traps.o serial_smc.o serial_scc.o cpu.o cpu_init.o speed.o \ ---<snip>--- COBJS-$(CONFIG_ETHER_ON_SCC) = ether_scc.o ---<snip>--- $(LIB): $(OBJS) $(call cmd_link_o_target, $(OBJS) $(obj)kgdb.o) The link rule `$(call cmd_link_o_target, $(OBJS) $(obj)kgdb.o)' is weird. kbdg.o is not included in $(OBJS) but linked into $(LIB) and $(LIB) is not dependent on kgdb.o. (Broken dependency tracking) So, START = start.o kgdb.o shoud have been START = start.o SOBJS = kgdb.o That is why this commit adds kgdb.o to obj-y, not to extra-y. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de>
2013-10-31sandbox: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
2013-10-31ARM: imx-common: convert makefiles to Kbuild styleMasahiro Yamada
Multiple targets are included in arch/arm/imx-common/Makefile In order to refactor it, we need to tweak Makefile and spl/Makefile. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31ARM: mxs: Enable DCDC converter for battery bootMarek Vasut
In case the board detected sufficient voltage for battery boot, make sure the DCDC converter is ON and the board is not running only from linregs, otherwise an instability will be observed. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2013-10-31mx6: Remove PAD_CTL_DSE_120ohm from i.MX6DL's IPU1_DI0_PIN4 pinOtavio Salvador
This removes the PAD_CTL_DSE_120ohm as done for i.MX6Q's IPU1_DI0_PIN4 pin definition and makes it aligned with 3.0.35-4.1.0 and 3.12 mainline kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
generated by cgit v0.10.2 at 2024-08-10 12:07:08 (GMT)