| Age | Commit message (Collapse) | Author |
|---|
|
Add a proper device tree file for Orange Pi Zero boards from Xunlong,
which come with a Allwinner H2+ SoC (similar to H3).
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
The nanopi already had the CONFIG_SUN8I_EMAC=y enabled in it's defconfig
file, but was missing the &emac the device tree entry.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
This re-syncs the MACH_TYPE_xxx values from the Linux Kernel v4.9
release. In addition this removes all of the machine_arch_type and
machine_is_xxx logic that is unused in U-Boot. This removal removes a
large number of otherwise unused CONFIG values from the list to be
converted.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Adam Ford <aford173@gmail.com>
|
|
Isp-camera preview image will be broken when dual screen display mode.
This patch set isp/vop qos level higher to solve this problem.
We have verified this patch on rk3288-miniarm board.
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
|
|
rk3399 has two clock-controller: cru and pmucru, update the
rockchip_get_crui() API, and rockchip_get_clk() do not used for
other module.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Add 'max-frequency' for sdhci node for clock init.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
The veyron-minnie Kconfig referred to jerry by mistake.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The popmetal board using a HOST_VBUS_DRV gpio signal to control the
USB host port 5V power, add a fix regulator and pinctrl for it, and
enable the USB host1 controller with the vbus-supply.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip: tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
With entry_point now being an unsigned long we need to adapt the last
two debug prints to use %lX not %X.
Fixes: 11e1479b9e67 ("SPL: make struct spl_image 64-bit safe")
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Xilinx changes for v2017.03
- ATF handoff
- DT syncups
- gem: Use wait_for_bit(), add simple clk support
- Simple clk driver for ZynqMP
- Other small changes
|
|
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_DAVINCI_MMC (renamed to CONFIG_MMC_DAVINCI)
CONFIG_OMAP_HSMMC (renamed to CONFIG_MMC_OMAP_HS)
CONFIG_MXC_MMC (renamed to CONFIG_MMC_MXC)
CONFIG_MXS_MMC (renamed to CONFIG_MMC_MXS)
CONFIG_TEGRA_MMC (renamed to CONFIG_MMC_SDHCI_TEGRA)
CONFIG_SUNXI_MMC (renamed to CONFIG_MMC_SUNXI)
They are the same option names as used in Linux.
This commit was created as follows:
[1] Rename the options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_DAVINCI_MMC/CONFIG_MMC_DAVINCI/g
s/CONFIG_OMAP_HSMMC/CONFIG_MMC_OMAP_HS/g
s/CONFIG_MXC_MMC/CONFIG_MMC_MXC/g
s/CONFIG_MXS_MMC/CONFIG_MMC_MXS/g
s/CONFIG_TEGRA_MMC/CONFIG_MMC_SDHCI_TEGRA/g
s/CONFIG_SUNXI_MMC/CONFIG_MMC_SUNXI/g
'
[2] Commit the changes
[3] Create entries in driver/mmc/Kconfig.
(copied from Linux)
[4] Move the options with the following command
tools/moveconfig.py -y -r HEAD \
MMC_DAVINCI MMC_OMAP_HS MMC_MXC MMC_MXS MMC_SDHCI_TEGRA MMC_SUNXI
[5] Sort and align drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
|
|
MIPS no longer needs to have its own version of this macro now.
Fixes: 2a6713b09b8d ("move UL() macro from armv8/mmu.h into common.h")
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
Xilinx ATF extending options for passing images from BL2(FSBL)
to BL31. U-Boot SPL is FSBL replacement that's why it should generate
handoff structure the same. Support only one entry which is U-Boot in
EL2 itself. When FIT image is adopted structure generate should be data
driven.
Currently ATF is placing this structure at the beggining of OCM which is
rewriting early parts of ATF which should be unused at that time.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add a string description for SYS_VENDOR to allow configuring boards from
other vendors than just "xilinx".
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The Zynq Ultrascale MP uses version 1.4 of the Cadence IP core
which fixes some silicon bugs that needed software workarounds
in Version 1.0 that was used on Zynq systems.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Enable and use the clock driver routine
defined in clock driver toset required
clock appropriately.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Added the idle-states node to describe zynqmp idle states. Only cpu-sleep-0
idle state is added in this patch. References to the idle-states node are
added in all CPU nodes. Time values: entry/exit latencies and min-residency,
needs to be tuned. arm,psci-suspend-param is selected to comply with PSCIv1.0
and Extended StateID format.
Signed-off-by: Stefan Krsmanovic <stefan.krsmanovic@aggios.com>
Acked-by: Will Wong <willw@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Fix DT binding for usb nodes. Setup correct aliases and enable dwc3
nodes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Just sync between version. Others zynqmp boards have this setup.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The watchdog clock node is missing.
Add the same. This solves the below error.
cdns-wdt fd4d0000.watchdog: input clock not found
cdns-wdt: probe of fd4d0000.watchdog failed with error -2
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
spi-max-frequency for spi bus depends on devices which are
connected to it. Remove this parameter from dtsi file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add usb ether gadget device with usb_ether_init() when
CONFIG_DM_ETH and CONFIG_USB_ETHER are defined.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The SPL load address changes based on boot type in HS devices,
ISW_ENTRY_ADDR is used to set this address for AM43xx based SoCs
for similar reasons. Add this same logic for AM33xx devices.
Also make the default value for ISW_ENTRY_ADDR correct for GP
devices based on SoC, HS devices already pick the correct
value in their defconfig.
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
When TI_SECURE_DEV_PKG is not defined we warn that the file '*_HS' was
not generated but generate an unsigned one anyway, first fix this
warning to say that it was generated but not secured.
When the user then exports TI_SECURE_DEV_PKG after getting this warning,
and tries to re-build, 'make' will detect the build artifacts as
unchanged and so assume they do not need to be re-generated. This causes
it to fail to sign the files and it will pack unsigned files into the
final image, even though TI_SECURE_DEV_PKG is now correctly defined and
working.
Fix this by using FORCE on the targets causes them to be re-run even if
the dependent files have not changed.
This then causes another issue. We currently rename the signed dtb files
to overwrite the non-signed ones. We do this so the 'mkimage' tool gives
the packaged dtb sections the correct name. If we do not rename the files
then SPL will not find them during boot.
Fix this by renaming the dtb files by appending _HS to the end of the
filename, after the ".dtb", this causes them to still be named correctly
in the FIT blob.
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
|
|
Use Kconfig option SYS_PPC64 instead.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use Kconfig option to select chassis version.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use Kconfig option E6500 and clean up existing usage.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
After most config options are moved to Kconfig, the unused ifdef
or elif can be removed.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use Kconfig to select DDR version instead of using config header.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
These two macros are used for the same thing, the total number of DDR
controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and
merge existing usage.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing
usage in ls102xa and fsl-layerscape. Remove all powerpc macros in
config header and board header files.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use Kconfig to select errata workaround.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Add option SYS_FSL_ERRATUM_ESDHC111, SYS_FSL_ERRATUM_ESDHC13,
SYS_FSL_ERRATUM_ESDHC135, SYS_FSL_ERRATUM_ESDHC_A001 to mmc Kconfig.
Move existing macros to related Kconfig.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate bk4r1]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Use Kconfig to select errata workaround.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Remove this macro. It was added by e622d9ed but actually wasn't used.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use TARGET_T2080RDB from Kconfig instead.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use TARGET_T2080QDS from Kconfig instead.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use TARGET_T1040QDS from Kconfig instead.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Remove these SoCs from Kconfig because they don't have individual
configuration. Clean up existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use Kconfig option to set little- or big-endian access to secure
boot and trust architecture.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Instead of define CONFIG_SYS_FSL_SEC_COMPAT in header files for PowerPC
and ARM SoCs, move it to Kconfig under the driver.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use Kconfig SYS_PPC_E500_DEBUG_TLB and clean up existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate 8572]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Use Kconfig option for SYS_NUM_TLBCAMS and clean up existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Use Kconfig option for E500 and E500MC macros.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Now that the SPL is ready to be compiled in AArch64 and the DRAM
init code is ready, enable SPL support for the A64 SoC and in the
Pine64 defconfig.
For now we keep the boot0 header in the U-Boot proper, as this allows
to still use boot0 as an SPL replacement without hurting the SPL use
case.
We disable FEL support for now by making its compilation conditional
and disabling it for ARM64, as the code isn't ready yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
