summaryrefslogtreecommitdiff
path: root/board/freescale/ls1043ardb
AgeCommit message (Collapse)Author
2016-05-18armv8: ls1043ardb: invert irq pin polarity for AQR105 PHYShaohui Xie
To use AQR105 PHY's interrupt, we need to invert the IRQ pin polarity by setting relative bit in SCFG_INTPCR register, because AQR105 interrupt is low active but GIC accepts high active. Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18armv8: ls1043ardb: fix types of variablesQianyu Gong
Using u16 for cfg_rcw_src and u8 for sd1refclk_sel is enough. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18armv8: ls1043a: remove redundant code in board filesQianyu Gong
gd->env_addr will be initialized in env_init() in common/env_nowhere.c if CONFIG_ENV_IS_NOWHERE is defined. So no need to do it again. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18armv8/ls1043ardb: fix the limitation of using 'cpld reset'Qianyu Gong
The current 'cpld reset' will just write global_rst register but couldn't switch to NOR boot if the board's switches are for NAND/SD boot. So need to write rcw source registers for NOR boot as well. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-17armv8/ls1043: Add workaround for DDR erratum A-008850Shengzhou Liu
Barrier transactions from CCI400 need to be disabled till the DDR is configured, otherwise it may lead to system hang. The patch adds workaround to fix the erratum. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-14Kconfig: Move CONFIG_FIT and related options to KconfigSimon Glass
There are already two FIT options in Kconfig but the CONFIG options are still in the header files. We need to do a proper move to fix this. Move these options to Kconfig and tidy up board configuration: CONFIG_FIT CONFIG_OF_BOARD_SETUP CONFIG_OF_SYSTEM_SETUP CONFIG_FIT_SIGNATURE CONFIG_FIT_BEST_MATCH CONFIG_FIT_VERBOSE CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_RSA Unfortunately the first one is a little complicated. We need to make sure this option is not enabled in SPL by this change. Also this option is enabled automatically in the host builds by defining CONFIG_FIT in the image.h file. To solve this, add a new IMAGE_USE_FIT #define which can be used in files that are built on the host but must also build for U-Boot and SPL. Note: Masahiro's moveconfig.py script is amazing. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Add microblaze change, various configs/ re-applies] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-02-24board: ls1043ardb: Modify pin-muxing code for USB and QE-HDLCZhao Qiang
QE-HDLC and USB multi-use the pins, modify the pin-muxing code for them, when set "hwconfig=qe-hdlc" in uboot, assign the pins to QE-HDLC, if not, assgin it to USB Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24board: ls1043rdb: Move USB muxing config to config_board_muxZhao Qiang
Pin-muxing code should be in config_board_mux, move USB muxing config to config_board_mux. Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24board: ls1043ardb: Add micro QE support for ls1043ardbZhao Qiang
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2015-12-17armv8/ls1043ardb/rcw: change core frequency to 1600MHzMingkai Hu
Change RCW for SD boot and NAND boot. Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-15armv8/ls1043ardb: add SECURE BOOT target for NORAneesh Bansal
LS1043ARDB Secure Boot Target from NOR has been added. - Configs defined to enable esbc_validate. - ESBC Address in header is made 64 bit. - SMMU is re-configured in Bypass mode. Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-15armv8: fsl-layerscape: Make DDR non secure in MMU tablesYork Sun
DDR has been set as secure in MMU tables. Non-secure master such as SDHC DMA cannot access data correctly. Mixing secure and non- secure MMU entries requirs the MMU tables themselves in secure memory. This patch moves MMU tables into a secure DDR area. Early MMU tables are changed to set DDR as non-secure. A new table is added into final MMU tables so secure memory can have 2MB granuality. gd->secure_ram tracks the location of this secure memory. For ARMv8 SoCs, the RAM base is not zero and RAM is divided into several banks. gd->secure_ram needs to be maintained before using. This maintenance is board-specific, depending on the SoC and memory bank of the secure memory falls into. Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-14armv8/ls1043ardb: Add support for >2GB memoryShaohui Xie
This patch also expose the complete DDR region(s) to Linux. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30armv8/ls1043ardb: add USB supportGong Qianyu
Add support for the third USB controller for LS1043A. Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-10ls1043ardb: Add missing config entries to MAINTAINERSFabio Estevam
ls1043ardb_nand_defconfig and ls1043ardb_sdcard_defconfig are missing in the MAINTAINERS file, so add them for completeness. Reported-by: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2015-10-29armv8/ls1043ardb: Add sd boot supportGong Qianyu
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8/ls1043ardb: esdhc: Add esdhc support for ls1043ardbYangbo Lu
This patch adds esdhc support for ls1043ardb. Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8/ls1043a: Add Fman supportShaohui Xie
Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8/ls1043ardb: Add nand boot supportGong Qianyu
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29armv8/ls1043ardb: Add LS1043ARDB board supportMingkai Hu
LS1043ARDB Specification: ------------------------- Memory subsystem: * 2GByte DDR4 SDRAM (32bit bus) * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 16 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * XFI 10G port * QSGMII with 4x 1G ports * Two RGMII ports PCIe: * PCIe2 (Lanes C) to mini-PCIe slot * PCIe3 (Lanes D) to PCIe slot USB 3.0: two super speed USB 3.0 type A ports UART: supports two UARTs up to 115200 bps for console Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
generated by cgit v0.10.2 at 2024-11-19 02:15:24 (GMT)