summaryrefslogtreecommitdiff
path: root/board/freescale
AgeCommit message (Collapse)Author
2018-01-29fsl: common :qixis: Add ifc and emmc switch support in qixisAshish Kumar
Previously only SD, NAND etc were secondary boot source and had IFC-NOR as primary booting target. But for SoC like LS1088 IFC-NOR can be secondary boot source, while QSPI-NOR is primary booting target, So add options in qixis to switch to other targets using new commands. E.g. '=> qixis_reset ifc' : switch to ifc '=> qixis_reset emmc' : switch to emmc Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
2018-01-19board:ls1012a2g5rdb: define PFE firmware address in kconfigBhaskar Upadhaya
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
2018-01-19board: ls1012a: update mdio, phy parameters based on serdes protocolBhaskar Upadhaya
mdio bus and phy-id needs to be configured based on serdes protocol 3508, 2208 selected via RCW. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
2018-01-19board: ls1012a2g5rdb: avoid phy resetBhaskar Upadhaya
ls1012a2g5rdb does not have requirement of phy reset, so placing reset_phy code for ls1012ardb only. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
2018-01-18armv8: ls1088a: vid: Add some function in SPL for VIDPankit Garg
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
2018-01-18ls1088a: Add VID support for QDS and RDB platformsRajesh Bhagat
This patch adds the support for VID on LS1088AQDS and LS1088ARDB systems. It reads the fusesr register and changes the VDD accordingly by adjusting the voltage via LTC3882 regulator. This patch also takes care of the special case of 0.9V VDD is present in fusesr register. In that case,it also changes the SERDES voltage by disabling the SERDES, changing the SVDD and then re-enabling SERDES. Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
2018-01-18common: board_f: vid: Add VID specific API to adjust core voltageRajesh Bhagat
Adds a VID specific API in init_sequence_f and spl code flow namely init_func_vid which is required to adjust core voltage. VID specific code is required in spl, hence moving flag CONFIG_VID out of spl flags. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
2018-01-18ls1088a: ddr: configure DDR for 0.9v for VID supportRajesh Bhagat
When VID feature is supported, check the contents of fuse register and configure DDR operate at 0.9v. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
2018-01-18board: common: vid: Add support for LTC3882 voltage regulator chipRajesh Bhagat
Restructures common driver to support LTC3882 voltage regulator chip. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
2018-01-18Kconfig: Add LTC3882 voltage regulator configRajesh Bhagat
Adds below LTC3882 voltage regulator config: CONFIG_VOL_MONITOR_LTC3882_READ CONFIG_VOL_MONITOR_LTC3882_SET Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
2018-01-18board: common: vid: Move IR chip specific code in flagRajesh Bhagat
Moves IR chip (IR36021) specific code in flag to resolve compilation issue where it is not present. For example, LS1088A is having a new LTC3882 voltage chip. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
2018-01-18board: common: vid: Add board specific vdd adjust APIRajesh Bhagat
Adds a board specific API namely board_adjust_vdd which is required to define the board VDD adjust settings. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
2018-01-18board: common:vid: Add LS1088A VID Supported voltage valuesRajesh Bhagat
Adds below voltage values supported by LS1088A Soc: 1.025 V(default), 0.9875V, 0.9750 V, 0.9V, 1.0 V, 1.0125 V, 1.0250 V Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
2018-01-17configs: ls1012a: add pfe configuration for LS1012ACalvin Johnson
Add configurations for PFE. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Changes in v2: -Moved SYS_LS_PFE_FW_ADDR from pfe Kconfig to board Kconfigs -Add "pfe stop" to ls1012a rdb, frdm and 2g5rdb config files
2018-01-17board: freescale: ls1012ardb: enable network support on ls1012ardbCalvin Johnson
This patch enables ethernet support for ls1012ardb. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Changes in v2: -split from original patch "board: freescale: ls1012a: enable network support on ls1012a platforms" -fix RGMII TX-delay issue
2018-01-17board: freescale: ls1012afrdm: enable network support on ls1012afrdmCalvin Johnson
This patch enables ethernet support for ls1012frdm. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Changes in v2: -split from original patch "board: freescale: ls1012a: enable network support on ls1012a platforms"
2018-01-17board: freescale: ls1012aqds: enable network support on ls1012aqdsCalvin Johnson
This patch enables ethernet support for ls1012aqds. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Changes in v2: -split from original patch "board: freescale: ls1012a: enable network support on ls1012a platforms"
2018-01-12board: ls1012a: LS1012A-2G5RDB board supportBhaskar Upadhaya
LS1012A-2G5RDB belongs to LS1012A family with features 2 2.5G SGMII PFE MAC, SATA, USB 2.0/3.0, WiFi DDR, eMMC, QuadSPI, UART Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
2018-01-12u-boot: fixup the iommu-map property of fsl-mc nodeNipun Gupta
The iommu-map property in the fsl-mc node is updated by valid stream-ids by u-boot. This patch is to fixup this property for LS208x and LS1088. Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
2018-01-10ls1088aqds: Enable IFC and QIXIS in SPL imageVinitha Pillai-B57223
Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
2018-01-10ls1088ardb: Add SD Secure boot target supportVinitha V Pillai
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
2018-01-10configs: SECURE_BOOT: Enable CONFIG_CMD_EXT4_WRITEVinitha V Pillai
As part of chain of trust with confidentiality along with distro boot, linux kernel image needs to be stored in encrypted form on ext4 boot partition. So enable CONFIG_CMD_EXT4_WRITE in case of Secure boot. Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
2018-01-10armv8: ls1088a: SPL size reductionVinitha V Pillai
Using changes in this patch we were able to reduce approx 8k size of u-boot-spl.bin image. Following is breif description of changes to reduce SPL size: 1. Changes in board/freescale/ls1088a/Makefile to remove compilation of eth.c and cpld.c in case of SPL build. 2. Changes in board/freescale/ls1088a/ls1088a.c to keep board_early_init_f funcations in case of SPL build. 3. Changes in ls1088a_common.h & ls1088ardb.h to remove driver specific macros due to which static data was being compiled in case of SPL build. Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
2018-01-09drivers/misc: Share qbman init between archsAhmed Mansour
This patch adds changes necessary to move functionality present in PowerPC folders with ARM architectures that have DPAA1 QBMan hardware - Create new board/freescale/common/fsl_portals.c to house shared device tree fixups for DPAA1 devices with ARM and PowerPC cores - Add new header file to top includes directory to allow files in both architectures to grab the function prototypes - Port inhibit_portals() from PowerPC to ARM. This function is used in setup to disable interrupts on all QMan and BMan portals. It is needed because the interrupts are enabled by default for all portals including unused/uninitialised portals. When the kernel attempts to go to deep sleep the unused portals prevent it from doing so Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com> Series-changes: 2 - Add get_qman_freq() to replace get_sys_info() for readability - Correct the copyright year in new files - Replace !ARM with PPC to wall off PowerPC SOCs specific qman setup - Rename portals.c -> fsl_portals.c for clarity Series-changes: 3 - Add freescale old copyright in new file since it is a modified copy - Add ifdef QBMAN guard around get_qman_freq() - Return freq_qman instead of freq_systembus. More readable and robust - Add white space before return line in get_qman_freq() Series-changes: 4 - Update function name setup_portals() to setup_qbman_portals() in files that were missed the first time Series-changes: 5 - Include <fsl_qbman.h> to fix missing prototype in p1023rdb.c
2017-12-26boards: ls1046ardb: disable unavailable "ethernet" node in dtsPrabhakar Kushwaha
Linux device tree contains "ethernet" node for all possible interface supported by SoC i.e. LS1046A. It is not necessary for a SerDes protocol to support all possible interface. So disable unavailable "ethernet" node in device tree. Also, enable FDT_SEQ_MACADDR_FROM_ENV to fetch MAC address sequentially from environment variables Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26armv8: ls1012ardb: support hwconfig for eSDHC1 enablingYangbo Lu
I2C reading for DIP switch setting is not reliable for LS1012ARDB RevD and later versions. This patch is to add hwconfig support to enable/disable eSDHC1 manually for these boards. Also drop 'status' fix-up for eSDHC0 and leave it as it is. It shouldn't always be fixed up with 'okay'. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26armv8: ls1012ardb: add more board version informationYangbo Lu
Add LS1012ARDB RevC/RevC1/RevC2/RevD/RevE information and detect it when u-boot starts up. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26armv8: ls1012ardb: clean up definitions for I2C IO expandersYangbo Lu
This patch is to clean up definitions for I2C IO expanders. The value 0x10 of __SW_BOOT_EMU is wrong. It should be 0x2. Fixed it in this patch. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26board/ls2080a, ls1088a: Add check for mc-dpl applied in fdtYogesh Gaur
Function fdt_fixup_board_enet() performs fdt fixup. Only return fdt_status_okay() when both MC is applied and DPL is deployed, else return fdt_status_fail(). This check is added to LS1088A/LS2080A/LS2088A boards. Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26armv8: ls1088ardb: support force SDHC mode by hwconfigYangbo Lu
The BRDCFG5[SPISDHC] register field of Qixis device is used to control SPI and SDHC signal routing. 10 = Force SDHC Mode - SPI_CS[0] is routed to CPLD for SDHC_VS use. - SPI_CS[1] is unused. - SPI_CS[2:3] are routed to the TDMRiser slot. 11 = Force eMMC Mode - SPI_CS[0:3] are routed to the eMMC card. 0X = Auto Mode - If SDHC_CS_B=0 (SDHC card installed): Use SDHC mode described above. - Else SDHC_CS_B=1 (no SDHC card installed): Use eMMC mode described above. In default the hardware uses auto mode, but sometimes we need to use force SDHC mode to support SD card hotplug, or SD sleep waking up in kernel. This patch is to support force SDHC mode by hwconfig. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26armv8: LS1088A_QSPI: Add secure boot defconfigs for QSPI boot.Udit Agarwal
Add the secure boot defconfigs for QSPI boot on LS1088ARDB and LS1088AQDS platforms. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26armv8: LS1088A_QSPI: SECURE_BOOT: Images validationUdit Agarwal
Validates PPA, MC, DPC, Bootscript, DPL and Kernel images in ESBC phase using esbc_validate command. Enable validation of boot.scr script prior to its execution dependent on "secureboot" flag in environment Add header address for PPA to be validated during ESBC phase for LS1088A platform based on LAyerscape Chasis 3. Moves sec_init prior to ppa_init as for validation of PPA sec must be initialised before the PPA is initialised. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26armv8: ls1088: Add fsl_fdt_fixup_flashAshish Kumar
IFC-NOR and QSPI-NOR signals are muxed on SoC to save pins Add fsl_fdt_fixup_flash() to disable IFC-NOR node in dts if QSPI is enabled and vice-versa Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26powerpc: mpc85xx: Fix static TLB table for SDRAMYork Sun
Most predefined TLB tables don't have memory coherence bit set for SDRAM. This wasn't an issue before invalidate_dcache_range() function was enabled. Without the coherence bit, dcache invalidation doesn't automatically flush the cache. The coherence bit is already set when dynamic TLB table is used. For some boards with different SPL boot method, or with legacy fixed setting, this bit needs to be set in TLB files. Signed-off-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1088aqds: Add SD boot support for ls1088qdsAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-15armv8: ls1088ardb: Add SD boot support for ls1088Ashish Kumar
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-06MAINTAINERS: Add missing boards and config entriesTom Rini
As part of my usual round of build testing, output about missing MAINTAINERS information was not logged, and thus often overlooked. Correct that mistake by ensuring that I log the output of genboardscfg.py every time. As part of that, address a number of missing MAINTAINERS entires. In the case of a missing file, I have put the original submitter down. In the rest of the cases I have added the config (and sometimes relevant header file) to the existing set of file globs. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-31mx6slevk: Call gpio_request()Fabio Estevam
We should call gpio_request() prior to reading the GPIO value. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-10-31imx: mx6slevk: cleanup board usb codePeng Fan
Since DM_USB enabled, no need the usb code in board file. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-10-27armv8: ls1088aqds: Change phy mode to PHY_INTERFACE_MODE_RGMII_IDAshish Kumar
Since TX delay is now enabled only in PHY_INTERFACE_MODE_RGMII_ID PHY_INTERFACE_MODE_RGMII_TXID. These change where introduced in phy driver in commit 05b29aa0cb68 ("net: phy: realtek: fix enabling of the TX-delay for RTL8211F"). Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-12Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2017-10-12mx6sabresd: Include <usb/ehci-ci.h> header fileDiego Dorta
When compiling with W=1 the following warning is observed: board/freescale/mx6sabresd/mx6sabresd.c:586:5: warning: no previous prototype for ‘board_ehci_hcd_init’ [-Wmissing-prototypes] int board_ehci_hcd_init(int port) Remove this warning by including <usb/ehci-ci.h>. Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
2017-10-12mx6sabresd: Include <asm/mach-imx/spi.h> header fileDiego Dorta
When compiling with W=1 the following warning is observed: board/freescale/mx6sabresd/mx6sabresd.c:680:5: warning: no previous prototype for ‘board_spi_cs_gpio’ [-Wmissing-prototypes] int board_spi_cs_gpio(unsigned bus, unsigned cs) Remove this warning by including <asm/mach-imx/spi.h>. Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
2017-10-12imx: Include <input.h> header fileDiego Dorta
When building with W=1 errors like the one below is seen: board/freescale/mx6sabresd/mx6sabresd.c:546:5: warning: no previous prototype for ‘overwrite_console’ [-Wmissing-prototypes] int overwrite_console(void) Fix the build warnings by including <input.h>. Signed-off-by: Diego Dorta <diego.dorta@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-10-12mx6sabresd: Avoid calling setup_display() from SPL codeFabio Estevam
There is no need call setup_display() from SPL code, so move it to board_init(), which executes only in U-Boot proper. Reported-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-10-09armv8: ls1043ardb: Use static DDR setting for SPL bootYork Sun
This board has soldered DDR chips. To reduce the SPL image size, use static DDR setting instead of dynamic DDR driver. Signed-off-by: York Sun <york.sun@nxp.com>
2017-10-09armv8: ls1088a: Update MC boot sequenceBogdan Purcareata
The MC boot sequence is contained in mc_env_boot. Update LS1088A boards to use this function, and hook it to reset_phy so that it's called late enough, after the ports have been initialized, for proper DPC / DPL fixup. Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-22board/ls2080ardb: Update board env based on SoCPriyanka Jain
As per current implementation, default value of board env is based on board filename i.e ls2080ardb. With distro support changes, this env is used to decide upon kernel dtb which is different for other SoCs (ls2088a, ls2081a) combination supported with this board. Add support to modify board env at runtime based on SoC type Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-18imx: imx7d: remove CamelCase from ENET_xMHz macrosEric Nelson
Update these macros to use all upper-case to avoid checkpatch warnings: ENET_25MHz, ENET_50MHz, ENET_125MHz, Signed-off-by: Eric Nelson <eric@nelint.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-09-11armv8: ls1088aqds: Add support of EC1 and EC2Prabhakar Kushwaha
EC1 and EC2 are RGMII interface on ls1088aqds platform. This patch add support of RGMII with PHY and MDIO Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com> Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
generated by cgit v0.10.2 at 2024-10-08 18:03:15 (GMT)