| Age | Commit message (Collapse) | Author |
|---|
|
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
imx_ddr_size() can be used to calculate the DDR size in runtime.
By using this function we no longer need to define PHYS_SDRAM_SIZE.
Cc: Martin Donnelly <martin.donnelly@ge.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Don't try to configure the backlight when CONFIG_VIDEO_IPUV3 isn't set.
Signed-off-by: Andrew Shadura <andrew.shadura@collabora.co.uk>
|
|
On a reset/reboot, the display power needs to be off for atleast 500ms
before turning it back on. So add a delay to the boot process to meet
the display timing requirement.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Setup the LCD backlight brightness control pin to use PWM
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
To generate accurate pixel clocks required by the displays we need to
set the ldb_di_clk source on bx50v3 to PLL3 and b850v3 to PLL5. Since
PLL5 is disabled on reset, we need to enable PLL5.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
B450v3/B650v3 uses single channel LVDS and does not support HDMI.
B850v3 uses dual channel LVDS and supports HDMI. Hence split the display
setup into two different functions.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Certain pins are not used on the i.MX6, and should have a neutral
pad configuration in order to reduce electrical interference on
the board. This commit defines these pins with a default value
rather than relying on the system defaults.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Add support for GE B450v3, B650v3 and B850v3 boards. The boards
are based on Advantech BA16 module which has a i.MX6D processor.
The boards support:
- FEC Ethernet
- USB Ports
- SDHC and MMC boot
- SPI NOR
- LVDS and HDMI display
Basic information about the module:
- Module manufacturer: Advantech
- CPU: Freescale ARM Cortex-A9 i.MX6D
- SPECS:
Up to 2GB Onboard DDR3 Memory;
Up to 16GB Onboard eMMC NAND Flash
Supports OpenGL ES 2.0 and OpenVG 1.1
HDMI, 24-bit LVDS
1x UART, 2x I2C, 8x GPIO,
4x Host USB 2.0 port, 1x USB OTG port,
1x micro SD (SDHC),1x SDIO, 1x SATA II,
1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
