Age | Commit message (Collapse) | Author |
|
|
|
The recent change to move the .bss outside of the image gives older
binutils (ld from eldk4.1/binutils-2.16) some headache:
ppc_85xx-ld: u-boot: Not enough room for program headers (allocated 3, need 4)
ppc_85xx-ld: final link failed: Bad value
We workaround it by being explicit about the program headers and not
assigning the .bss to a program header.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
schematic.
The Sequoia board has two UARTs in "4-pin" mode. This patch modifies the GPIO
configuration to match the schematic, and also sets the SDR0_PFC1 register to
select the corresponding mode for the UARTs.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
And in the process eliminate some duplicate register defines.
Signed-off-by: Kenneth Johansson <kenneth@southpole.se>
|
|
TASREG is ColdFire platform, the include ppc4xx.h in
board/esd/common/flash.c causes conflict.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
|
|
Rename OBJ to COBJ in board/platform/Makefile
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
|
|
Rename int mii_init(void) to void mii_init(void) for idmr
ColdFire platform
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
* Move to using absolute addressing always. Makes the scripts a bit more
portable and common
* Moved .bss after the end of the image. These allows us to have more
room in the resulting binary image for code and data.
* Removed .text object files that aren't really needed
* Make sure _end is 4-byte aligned as the .bss init code expects this.
(Its possible that the end of .bss isn't 4-byte aligned)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Support for the adsvix was originally provided by Applied Data
Systems (ADS), inc., now EuroTech, Inc.
The board never shipped aside from some sample boards.
Signed-off-by: Adrian Filipi <adrian.filipi@eurotech.com>
|
|
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
Signed-off-by: Detlev Zundel <dzu@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
|
|
|
|
|
|
The MVBC_P is a MPC5200B based camera system with Intel Gigabit ethernet
controller (using e1000) and custom Altera Cyclone-II FPGA on PCI.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Update the sys_eeprom.c file to handle both NXID and CCID EEPROM formats. The
NXID format replaces the older CCID format, but it's important to support both
since most boards out there still use the CCID format. This change is in
preparation for using one file to handle both formats. This will also unify
EEPROM support for all Freescale 85xx and 86xx boards.
Also update the 86xx board header files to use the standard CFG_I2C_EEPROM_ADDR
instead of ID_EEPROM_ADDR.
Signed-off-by: Timur Tabi <timur@freescale.com>
|
|
Add support for using a PCIe ATI Video card on PCIe2.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add in for the sbc8560, the ft_board_setup() routine, based on what is
in use for the Freescale MPC8560ADS board.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
The sbc8560 board ships with 512MB of memory installed,
but the current cs0_bnds is hard coded for 256MB. Set the
value based on CFG_SDRAM_SIZE.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
ARM DaVinci: Remove extern phy_t declaration by moving
code to proper place.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
|
|
i2c_init()
ARM DaVinci: Remove duplicate definitions of MACH_TYPE
and prototype of i2c_init().
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
The 8544 DS doesn't have any cacheable Local Bus memories set up. By mapping
space for some anyway, we were allowing speculative loads into unmapped space,
which would cause an exception (annoying, even if ultimately harmless).
Removing LBC_CACHE_BASE, and using LBC_NONCACHE_BASE for the LBC LAW solves the
problem.
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
This patch removes some ft_board_setup() functions from some 4xx boards.
This can be done since we now have a default weak implementation for this
in cpu/ppc4xx/fdt.c. Only board in need for a different/custom
implementation like canyonlands need their own version.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
|
|
|
|
|
|
On the at91sam9260ep development board there is an EEPROM
connected to the TWI interface (PA23, PA24 Peripheral A
multiplexing), so we cannot use these pins as ETX2, ETX3.
This patch configures PA10, PA11 pins for ETX2, ETX3
instead of PA23, PA24 pins.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Manuel Sahm <Manuel.Sahm@feig.de>
|
|
The DIU_DIV register is 8 bit not 5 bit. This prevented large DIV values
so it was not possible to set a slow pixel clock and thus prevented
display on small screens.
Signed-off-by: Kenneth Johansson <kenneth@southpole.se>
Acked-by: John Rigby <jrigby@freescale.com>
|
|
board/ads5121/iopin.c
Replace bit fields in struct iopin_t with a single
field and intialize it via plain old macros.
This fixes the type pun warnings and makes the code
more readable.
board/ads5121/ads5121.c
Add include iopin.h to ads5121.c for the iopin_initialize
prototype.
Add an extern void ads5121_diu_init(void)
Signed-off-by: John Rigby <jrigby@freescale.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Rename int mii_init(void) to void mii_init(void)
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
|
|
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
|