| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: David Feng <fenghua@phytium.com.cn>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
|
|
Byte offset of Ethernet mac address read from e-fuse are wrong so DHCP is
not working on some boards, modifying the offset to read properly.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
|
|
The omap3_zoom2 board has not been updated for a correct CONFIG_SYS_HZ
and Tom Rix's email has long been bouncing.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
|
|
Conflicts:
include/micrel.h
The conflict above was trivial, caused by four lines being
added in both branches with different whitepace.
|
|
This fix is necessary after increased by one the number
of adapters in s3c24x0 driver.
Tested on Trats and Trats2.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch adds dts support for SMDK5420.
exynos5.dtsi created is a common file which has the nodes common
to both 5420 and 5250.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Adding the base patch for Exynos based SMDK5420.
This shall enable compilation and basic boot support for
SMDK5420.
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Create a common board.c file for all functions which are common across
all EXYNOS5 platforms.
exynos_init function is provided for platform specific code.
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH).
Adding details for the same.
Below is the brief description of DDR3 init sequence(SW leveling):
-> Enable VTT regulator
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program leveling registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A)
Adding LPDDR2 init sequence and register details for the same.
Below is the brief description of LPDDR2 init sequence:
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
-> Wait till initialization is complete and the configure MR registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Currently same value is programmed for all ioregs. This is not
the case for all SoC's like AM4372. So adding a structure for ioregs
and updating in all board files. And also return from config_cmd_ctrl()
and config_ddr_data() functions if data is not passed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Fixup dxr2, cm_t335, adapt pcm051 rev3]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Updating the Multiplier and Dividers value for all DPLLs.
Safest OPP is read from DEV ATTRIBUTE register. Accoring to the value
returned the MPU DPLL is locked.
At different OPPs follwoing are the MPU locked frequencies.
OPP50 300MHz
OPP100 600MHz
OPP120 720MHz
OPPTB 800MHz
OPPNT 1000MHz
According to the latest DM following is the OPP table dependencies:
VDD_CORE VDD_MPU
OPP50 OPP50
OPP50 OPP100
OPP100 OPP50
OPP100 OPP100
OPP100 OPP120
So at different OPPs of MPU it is safest to lock CORE at OPP_NOM.
Following are the DPLL locking frequencies at OPP NOM:
Core locks at 1000MHz
Per locks at 960MHz
LPDDR2 locks at 266MHz
DDR3 locks at 400MHz
Touching AM33xx files also to get DPLL values specific to board but no
functionality difference.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Updating the mux data for UART, adding data for i2c0 and mmc.
And also updating pad_signals structure.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
CONFIG_ENV_VARS_UBOOT_CONFIG, CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and
CONFIG_BOARD_LATE_INIT is already set. Adding support to detect the
board. These variables are used by findfdt.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add support for reading onboard EEPROM to enable
board detection.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Use ti_armv7_common.h config file to inclde the common
configs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
|
|
|
|
Add support for the new Tamonten™ NG platform from Avionic Design.
Currently only I2C, MMC, USB and ethernet have been tested.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
When DT define aliases for etherner0 and ethernet1, U-Boot
automatically patched MAC addresses using ethaddr and eth1addr
environment variables respectively.
Custom initialization is no longer needed.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>
|
|
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>
|
|
|
|
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
The koelsch board has one sh-ether device.
This supports sh-ether.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
The lager board uses I2C for reset.
ned-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
The lager board has one sh-ether device.
This supports sh-ether.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
mx6sabresd boards have a 18-bit LVDS data width and the correct color format
is RGB666.
Suggested-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
HSYNC, VSYNC and DISP_CLK are very useful display signals for debugging.
Configure them as active pins.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
This patch adds support for the AMPIRE 800x480 LCD panel that is available
for M53EVK.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Align with the context to use readl() to read the CCM_CCGR3
register with memory barrier instead of __raw_readl().
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Add SATA support on uDoo Board.
Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Move setup_sata function definition from platform file nitrogen6x.c
to arch/arm/imx-common/sata.c to avoid code duplication.
Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
As the cs for spi is worked in gpio mode, so no need to configure
it as peripheral and then configure to gpio. Configure it to gpio
directly.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
This allows the use of either or both declarations from
the files mx6q_pins.h and mx6dl_pins.h.
All board files should include <asm/arch/mx6-pins.h>
with one of the following defined in boards.cfg
MX6Q - for boards targeting i.MX6Q or i.MX6D
MX6DL - for boards targeting i.MX6DL
MX6S - for boards targeting i.MX6S
MX6QDL - for boards that support any of the above with
run-time detection
Pad declarations will be MX6_PAD_x for single-variant boards
and MX6Q_PAD_x and MX6DL_PAD_x for boards supporting both
processor classes.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
The pmic_init() function has the I2C or SPI bus number that is connected to the
PMIC.
Instead of passing I2C_PMIC, explicitly pass the I2C bus number via I2C_x
definition.
The motivation for doing this is to avoid people just doing a copy and paste
of I2C_PMIC into their board file when another I2C bus is actually used to
interface to their PMIC.
This also makes more obvious which is the I2C bus connected to the PMIC, without
having to search in the source code for the meaning of the 'I2C_PMIC' number.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Pin 30 is connected to PHY's RESET# signal, so it must be
put to high. Otherwise PHY won't be found via MDIO interface.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
|
|
Add SPL U-Boot support to replace x-loader on the Compulab cm_t35
board. Currently only the 256MiB SDRAM board versions are supported.
Tested by booting via MMC and NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
The Head acoustics (HA) baseboard used the Technexion TAO3530 SOM
and has only some minor differences to the Technexion Thunder baseboard.
This patch adds support for this HA baseboard / TAO3530 as the "omap3_ha"
build target.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
|
|
The memory size is autodetected and is passed to the Linux kernel
either via ATAGs or device-tree (dtb). So there is no need to
pass it via the bootargs.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
|
|
Add SPL support for the Technexion TAO3530 SOM to replace
x-loader. Tested with the Thunder baseboard. Currently this is
only tested with the TAO3530 SOM revision (Ax/Bx).
Tested by booting via MMC and NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
|
|
Add support for TechNexion TAO3530 SoM
This patch has been posted quite a long time ago. I ported it to
the latest mainline U-Boot version. With some additional cleanup
and enhancements.
Signed-off-by: Tapani Utriainen <tapani@technexion.com>
CC: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
|
|
Test on Beaglebone white over cpsw, usb ether and SD card (read and
write), performance increased, crc32 of data matches.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Conflicts:
board/samsung/trats2/trats2.c
include/configs/exynos5250-dt.h
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Conflicts:
arch/arm/cpu/armv7/rmobile/Makefile
doc/README.scrapyard
Needed manual fix:
arch/arm/cpu/armv7/omap-common/Makefile
board/compulab/cm_t335/u-boot.lds
|
|
|
|
|
|
This adds a SPI flash driver which simulates SPI flash clients.
Currently supports the bare min that U-Boot requires: you can
probe, read, erase, and write. Should be easy to extend to make
it behave more exactly like a real SPI flash, but this is good
enough to merge now.
sjg@chromium.org added a README and tidied up code a little.
Added a required map_sysmem() for sandbox.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add support for USB-A9263 board manufactured by Calao Systems
(http://www.calao-systems.com/).
Code is based on old U-Boot sources (2010.09) released by Calao.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
