| Age | Commit message (Collapse) | Author |
|---|
|
|
|
EC1 pins in RCW can be selected as RGMII1, GPIO3, CAN1/2, FTM1 or
SAI1/2. There is a bug that EC3 RGMII could not work when selecting EC1
as other functionality except RGMII. The workaround is to select
ge2_clk125 for eTSEC clock muxing in register SCFG_ETSECCMCR.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
SystemID information could be read through I2C1 from EEPROM
on LS1021ATWR board.
As LS1 is a little-endian processor, getting the version ID by
be32_to_cpu() is wrong. Fix it by using e.version directly.
This change will be compatible for both ARM and PowerPC.
As there is an errata that I2C1 could not work in SD boot,
reading EEPROM through I2C1 is disabled too in SD boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
SCFG_SCFGREVCR is SCFG bit reverse register. This register
must be written with 0xFFFFFFFF before writing to any other
SCFG register. Then other SCFG register could be written in
big-endian mode.
Address: 157_0000h base + 200h offset = 157_0200h
Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15|16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
W/R SCFGREV
Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0-31
SCFGREV SCFG Bit Reverse Control Filed
32'h 0000_0000 - No bit reverse is applied
32'h FFFF_FFFF - Bit reverse is applied; so 31:0 will be stored/read as
0:31
This patch removes the bit reversing for SCFG registers in
u-boot. It will be implemented through PBI commands in RCW
.pbi
write 0x570200, 0xffffffff
.end
So other SCFG register could be written in big-endian mode
in u-boot or kernel directly.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Disable the snoop for slave interface 0, 1 and 2
to avoid the interleaving on the CCI400 BUS.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
|
|
Conflicts:
drivers/serial/serial-uclass.c
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Conflicts:
arch/x86/cpu/Makefile
Signed-off-by: Tom Rini <trini@ti.com>
|
|
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Cc: Eric Benard <eric@eukrea.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Provide board specific implementation for sata stop command for
cm_fx6.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
|
|
gw_ventana can boot from SPI or NAND and both of these interfaces boot from
the same 0x400 offset.
This means that we could simplify the code and replace the custom gw_ventana.cfg
with the generic spl_sd.cfg, as it provides the same boot offset of 0x400.
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Add arch/arm/cpu/armv7/Kconfig with non-secure and virt options, this is a
preparation patch for adding an env variable to choose between secure /
non-secure boot on non-secure boot capable systems, specifically this
prepares for adding CONFIG_ARMV7_BOOT_SEC_DEFAULT as a proper Kconfig option.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
To indicate that U-Boot is active, turn on the blue LED.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
The USB host code was missing gpio_request() calls before using the gpio
functions, causing errors to be printed out.
As a side note calls to max77686_set_buck_mode(OPMODE_OFF/OPMODE_ON) have
been removed, as they did not have any effect. This is as per Przemyslaw:
I looked into the documentation and there is a "ENB8" pin in PMIC package.
This pin allows steering BUCK8 ON/OFF by the hardware. If ENB8 is set to low
then you can do on/off. If high, then you cannot change its state by I2C
write, which seems to be the case with the Odroids.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
The sandbox/ext4/fat/generic fs commands do not gracefully deal with files
greater than 2GB. Negative values are returned in such cases.
To handle this, the fs functions have been modified to take an additional
parameter of type "* loff_t" which is then populated. The return value
of the fs functions are used only for error conditions.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Update board/gdsys/p1022/controlcenterd-id.c,
drivers/fpga/zynqpl.c for changes]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Change the internal FAT functions to use loff_t for offsets.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Fix fs/fat/fat.c for min3 updates]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
A number of prototypes here are now found in <flash.h>. use.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Some CPUs of some architectures have SOC directories.
At present, the build system directly descends into SOC directories
from the top Makefile, but it should generally descend into each
directory from its parent directory.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
bcm11130
bcm11130_nand
Signed-off-by: Steve Rae <srae@broadcom.com>
|
|
bcm911360_entphn
bcm911360_entphn-ns
bcm911360k
bcm958300k-ns
bcm958305k
- updates to support Cygnus and NSP board families better
- add functions so CONFIG_ARMV7_NONSEC can be enabled on Cygnus boards
Signed-off-by: Steve Rae <srae@broadcom.com>
|
|
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Based on similar patches by Fabio Estevam for mx6sabresd, mx53loco, wandboard
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Add platform data for the GPIO driver. It doesn't need to contain anything
since the GPIO driver will actually use information from the CONFIGs for
now. This merely serves to ensure that the GPIO driver is bound.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The old maintainer has left, so take this over.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Convert this at91sam9260-based board to use driver model. This should serve
as an example for other similar boards. Serial and GPIO are supported so
far.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Rename this vendor since it is intended to be used on any platform where
coreboot runs at reset and then loads U-Boot.
So far it is only tested on link. When other boards are supported it is
likely that we will need to move to multiple board names, all under the
'coreboot' vendor. So while it would be possible to remove the vendor for
now, that would be short-sighted.
Suggested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Enable GPIO support and provide the required GPIO setup information to
the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add support for CAR so that we have memory to use prior to DRAM init.
On link there is a total of 128KB of CAR available, although some is
used for the memory reference code.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
On x86 it is common to use 'post codes' which are 8-bit hex values emitted
from the code and visible to the user. Traditionally two 7-segment displays
were made available on the motherboard to show the last post code that was
emitted. This allows diagnosis of a boot problem since it is possible to
see where the code got to before it died.
On modern hardware these codes are not normally visible. On Chromebooks
they are displayed by the Embedded Controller (EC), so it is useful to emit
them. We must enable this feature for the EC to see the codes, so add an
option for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This board is a 'bare' version of the existing 'link 'board. It does not
require coreboot to run, but is intended to start directly from the reset
vector.
This initial commit has place holders for a wide range of features. These
will be added in follow-on patches and series. So far it cannot be booted
as there is no ROM image produced, but it does build without errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Use these new functions where possible. They default to a value of 2 so we
cannot use them in some places where we need a default value of 1.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
This function can fail if the device tree runs out of space. Rather than
silently booting with an incomplete device tree, allow the failure to be
detected.
Unfortunately this involves changing a lot of places in the code. I have
not changed behvaiour to return an error where one is not currently
returned, to avoid unexpected breakage.
Eventually it would be nice to allow boards to register functions to be
called to update the device tree. This would avoid all the many functions
to do this. However it's not clear yet if this should be done using driver
model or with a linker list. This work is left for later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
Add the pfuze100 initialization in power_init_board for imx6q/dl
sabreauto board.
Signed-off-by: Ye.Li <B37916@freescale.com>
|
|
Modify the pfuze init for mx6sxsabresd to use the shared
"pfuze_common_init" function. And move this initialization to
power_init_board.
Signed-off-by: Ye.Li <B37916@freescale.com>
|
|
Modify the pfuze init for mx6sabresd to use the shared
"pfuze_common_init" function. And move this initialization to
power_init_board.
Signed-off-by: Ye.Li <B37916@freescale.com>
|
|
Since the Pfuze initializations are similar on various mx6 SABRE
boards. Factorize the initialization to a common function in file
board/freescale/common/pfuze.c. So that all SABRE boards BSP can
share the function.
Signed-off-by: Ye.Li <B37916@freescale.com>
|
|
Add full support for USDHC2, USDHC3, USDHC4 on mx6sx sabresd board.
The default boot socket is USDHC4, so the MMC environment device and
mmcdev variable are set to this device.
Signed-off-by: Ye.Li <B37916@freescale.com>
|
|
In U-boot it is preferred to access the register via structure pointer, so
convert it such style.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
|
|
setup_i2c has a return value. Use it to give feedback
on error.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
|
|
Add include needed to have prototype for board_spi_cs_gpio
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
|
|
Let's add mx6sabresd_spl_defconfig entry into MAINTAINERS, so that we avoid
getting a warning that the mx6sabresd_spl is not maintained.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
We can simply the return the value from enable_fec_anatop_clock() to make the
code smaller and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
