| Age | Commit message (Collapse) | Author |
|---|
|
Turn all local symbols into static in order to make sparse happy.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
i2c_pad_info1 is only used locally, so it can be made static.
Fix the following sparse warning:
board/freescale/mx6sxsabresd/mx6sxsabresd.c:160:22: warning: symbol 'i2c_pad_info1' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
This adds NAND support for the Vybrid tower system (TWR-VF65GS10)
provided by the vf610_nfc driver. Full 16-Bit bus width is
supported. Also an aditional config vf610twr_nand is introduced
which gets the environment from NAND. However, booting U-Boot from
NAND is not yet possible due to missing boot configuration block
(BCB).
Signed-off-by: Stefan Agner <stefan@agner.ch>
|
|
Currently mx6dlsabresd shares the same DCD settings with the nitrogen board.
Provide a DCD configuration file specific to mx6dlsabresd with the settings
recommended by the Freescale hardware team.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
The leds array within struct ventana has space for 3 elements, but the
setup_board_gpio() function tries to set up 4 GPIOs for LEDs. Recent
versions of GCC complain about that:
board/gateworks/gw_ventana/gw_ventana.c: In function 'setup_board_gpio':
board/gateworks/gw_ventana/gw_ventana.c:987:27: warning: iteration 3u invokes undefined behavior [-Waggressive-loop-optimizations]
if (gpio_cfg[board].leds[i])
^
board/gateworks/gw_ventana/gw_ventana.c:986:2: note: containing loop
for (i = 0; i < 4; i++) {
^
Fix this by making the upper bound of the loop match the array size.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
|
|
Most Gateworks Ventana boards use a PLX PEX860x PCIe switch for PCIe expansion.
These boards use GPIO on the PLX device as PERST# for the downstream ports
thus we assert this when the PLX is enumerated.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
Add support for SATA.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
Use Compulab eeprom module to obtain revision number, serial number, and
mac address from the EEPROM.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
Add support for all 3 I2C busses on Compulab CM-FX6 CoM.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
Add USB and USB OTG host support for Compulab CM-FX6 CoM.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
Add ethernet support for Compulab CM-FX6 CoM
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
Add NAND support for Compulab CM-FX6 CoM.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
Add initial support for Compulab CM-FX6 CoM.
Support includes MMC, SPI flash, and SPL with dynamic DRAM detection.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
Create CONFIG_SYS_I2C_EEPROM_BUS #define to tell the EEPROM
module what I2C bus the EEPROM is located at. Make cl_eeprom_read()
switch to that bus when reading EEPROM.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
There are many similarities between the IMX6QUAD/IMX6DUAL and there are
many similarities between the IMX6SOLO/IMX6DUALITE. Add a 'soctype' env
variable that tells you which type you have.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
The GW5520 has an IMX6Q SoC with 512MB of DDR3, 256MB of NAND flash as well as:
* 2x MiniPCIe sockets
* 2x USB host sockets
* 2x i210 GigE
* HDMI out
* digital I/O expansion
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
The IMX6 MMDC calibration registers depend on propagation delay and capacitive
loading between the SoC's MMDC and the DDR3 chips. On the Ventana boards the
board layout varies little in trace-lengths such that propagation delays are
irrelevant thus we can simply things by using calibration values obtained
from various board layouts based on a common SoC and DDR chip configuration.
This eliminates board-model from being needed allowing more flexibility. These
values were tested on a large sample size of Gateworks Ventana boards ranging
in layout, and memory configuration over the entire temperature range supported.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
|
|
|
|
Add initialization code for peach_pit panel, parade bridge chip,
and backlight.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Previously, we used to statically assign values for vl_col, vl_row and
vl_bpix using #defines like LCD_XRES, LCD_YRES and LCD_COLOR16.
Introducing the function exynos_lcd_early_init() would take care of this
assignment on the fly by parsing FIMD DT properties, thereby allowing us
to remove LCD_XRES and LCD_YRES from the main config file.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch adds support for Olimex A20-OLinuXino-LIME board.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Patch is the result of:
sed -i -e 's/FTDFILE/FDTFILE/g' board/sunxi/Kconfig configs/* include/configs/sunxi-common.h
sed -i -e 's/ftdfile/fdtfile/g' board/sunxi/Kconfig
Reported-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
[ ijc -- s/Spotted-by/Reported-by/ and resolve conflict vs "remove
redundant "SPL" from CONFIG_SYS_EXTRA_OPTIONS" ]
|
|
This patch changes MPLL from 800MHz to 880MHz on Odroid.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Inderpal's email address is not working any more.
Chander will be a new maintainer.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This config is valid for two devices:
- Odroid X2,
- Odroid U3.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This board file supports standard features of Odroid X2 and U3 boards:
- Exynos4412 core clock set to 1000MHz and MPLL peripherial clock set to 800MHz,
- MAX77686 power regulator,
- USB PHY,
- enable XCL205 - power for board peripherials
- check board type: U3 or X2.
- enable Odroid U3 FAN cooler
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This change adds setup of environmental board info using
get_board_name() and get_board_type() functions for config
CONFIG_BOARD_TYPES.
This is useful in case of running many boards with just one config.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This change adds declaration of functions:
- set_board_type() - called at board_early_init_f()
- get_board_type() - called at checkboard()
For supporting multiple board types in a one config - it is welcome
to display the current board model. This is what get_board_type()
should return.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This change enable automatic setting of dfu alt info
on every boot. This is useful in case of booting one
u-boot binary from multiple media.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This change introduces new common function:
- set_dfu_alt_info() - put dfu system and bootloader setting
into $dfu_alt_info.
functions declaration:
- char *get_dfu_alt_system(void)
- char *get_dfu_alt_boot(void)
- void set_dfu_alt_info(void)
and new config:
- CONFIG_SET_DFU_ALT_INFO
This function can be used for auto setting dfu configuration on boot.
Such feature is useful for multi board support by one u-boot binary.
Each board should define two functions:
- get_dfu_alt_system()
- get_dfu_alt_boot()
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
It is possible to boot device using a micro SD or eMMC slots.
In this situation, boot device should be registered as a block
device 0 in the MMC framework, because CONFIG_SYS_MMC_ENV_DEV
is usually set to "0" in the most config cases.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
The byte order of soc revision was inverted, now it is fixed.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
The help message in board/ti/am335x/Kconfig says AM335x has
6 UARTs, so the valid number for CONFIG_CONS_INDEX is from 1 to 6.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
|
|
|
|
The QS Systems TQMa6 board support was added by commit cb07d74e
and lost by commit e82abaeb.
Commit e82abaeb merged the IMX branch based on pre-Kconfig
and the mainline based on post-Kconfig, simply deleting
the boards.cfg file. As a result, some boards added just before
the merge were lost.
This commit adds Kconfig, defconfig, MAINTAINERS for TQMa6 board
to work on the Kconfig infrastructure.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Nomadik board select menu to nomadik/Kconfig.
Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="nomadik").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Move Highbank-specific settings to highbank/Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Rob Herring <robh@kernel.org>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Orion5x board select menu to orion5x/Kconfig.
Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="orion5x").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Keystone board select menu to keystone/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="keystone").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP5 board select menu to omap5/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap5").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP4 board select menu to omap4/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap4").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP3 board select menu to omap3/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap3
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Davinci board select menu to davinci/Kconfig.
Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="davinci").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Exynos board select menu to exynos/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="exynos").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the KirkWood board select menu to kirkwood/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="kirkwood").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Prafulla Wadasdkar <prafulla@marvell.com>
Cc: Luka Perkov <luka@openwrt.org>
|
|
Move Versatile-specific settings to versatile/Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Rmobile board select menu to rmobile/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="rmobile").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
