summaryrefslogtreecommitdiff
path: root/cpu
AgeCommit message (Collapse)Author
2009-06-15Switched davinci_emac Ethernet driver to use newer APIBen Warren
Added CONFIG_NET_MULTI to all Davinci boards Removed all calls to Davinci network driver from board code Added cpu_eth_init() to cpu/arm926ejs/cpu.c Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15Moved Davinci Ethernet driver to drivers/netBen Warren
This driver has been renamed davinci_emac.c Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-12fsl/85xx, 86xx: Sync up DMA codePeter Tyser
The following changes were made to sync up the DMA code between the 85xx and 86xx architectures which will make it easier to break out common 8xxx DMA code: 85xx: - Don't set STRANSINT and SPCIORDER fields in SATR register. These bits only have an affect when the SBPATMU bit is set. - Write 0xffffffff instead of 0xfffffff to clear errors in the DMA status register. We may as well clear all 32 bits of the register... 86xx: - Add CONFIG_SYS_MPC86xx_DMA_ADDR define to address DMA registers - Add clearing of errors in the DMA status register when initializing the controller - Clear the channel start bit in the DMA mode register after a transfer Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-12fsl: Create common fsl_dma.h for 85xx and 86xx cpusPeter Tyser
Break out DMA structures for the Freescale MPC85xx and MPC86xx cpus to reduce a large amount of code duplication Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-12qe: Pass in uec_info struct through uec_initializeHaiying Wang
The uec driver contains code to hard code configuration information for the uec ethernet controllers. This patch creates an array of uec_info structures, which are then parsed by the corresponding driver instance to determine configuration. It also creates function uec_standard_init() to initialize all UEC interfaces for 83xx and 85xx. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-1285xx: Add QE clk supportHaiying Wang
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Acked-by: Timur Tabi <Timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-1285xx: Added MPC8535/E identifiersKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-06-1285xx: Always attempt ethernet device tree fixupKumar Gala
Its reasonable that we may have ethernet devices but dont have drivers or support enabled for them in u-boot and want the device tree fixed up. Unconditionally calling the ethernet fixup is fine since if we dont have ethernet nodes that match (or aliases) we will not attempt to do anything. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Timur Tabi <timur@freescale.com>
2009-06-12mpc512x: Fix problem with I2C access before relocationStefan Roese
This is needed for the upcoming esd MECP5123 board port which uses I2C EEPROM for environment storage. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com> Acked-by: Heiko Schocher<hs@denx.de>
2009-06-12mpc83xx: USB: Reorganized its supportVivek Mahajan
The following patch reorganizes/reworks the USB support for mpc83xx as under:- * Moves the 83xx USB clock init from drivers/usb/host/ehci-fsl.c to cpu/mpx83xx/cpu_init.c * Board specific usb_phy_type is read from the environment * Adds USB EHCI specific structure in include/usb/ehci-fsl.h * Copyrights revamped in most of the following files Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-06-1283xx: Replace CONFIG_MPC83[0-9]X with MPC83[0-9]xPeter Tyser
Use the standard lowercase "x" capitalization that other Freescale architectures use for CPU defines to prevent confusion and errors Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-06-1283xx: Replace CONFIG_MPC83XX with CONFIG_MPC83xxPeter Tyser
Use the standard lowercase "xx" capitalization that other Freescale architectures use for CPU defines to prevent confusion and errors Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-06-12mpc512x: Use serial_setbrg() in serial_init() to not duplicate the codeStefan Roese
This patch removes the duplicated code for baudrate generator configuration in the PSC serial_init() implementation by calling serial_setbrg() instead of duplicating the code. Signed-off-by: Stefan Roese <sr@denx.de>
2009-06-12mpc512x: Fix PSC divisor calculation for baudrate settingStefan Roese
The wrong input frequency was used in serial_setbrg(). This patch fixes this by using ips_clk as input frequency for the PSC baudrate generator. Signed-off-by: Stefan Roese <sr@denx.de>
2009-06-12MPC512x: remove include/mpc512x.hWolfgang Denk
Move needed definitions (register descriptions etc.) from include/mpc512x.h into include/asm-ppc/immap_512x.h. Instead of using a #define'd register offset, use a function that provides the PATA controller's base address. All the rest of include/mpc512x.h are register offset definitions which can be eliminated by proper use of C structures. There are only a few register offsets remaining that are needed in cpu/mpc512x/start.S; for these we provide cpu/mpc512x/asm-offsets.h which is intended as a temporary workaround only. In a later patch this file will be removed, too, and then auto-generated from the respective C structs. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: John Rigby <jcrigby@gmail.com>
2009-06-12MPC512x: use I/O accessors instead of pointer accessesWolfgang Denk
This commit changes the MPC512x code to use I/O accessor calls (i.e. out_*() and in_*()) instead of using deprecated pointer accesses. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: John Rigby <jcrigby@gmail.com>
2009-06-12MPC512x: add more hardware description to immap_512x.hWolfgang Denk
- add GPIO module description - add Address Latch Timing Register description - add IO Control Memory Map - add FEC Memory Map Also change board/freescale/mpc5121ads/mpc5121ads.c and cpu/mpc512x/iopin.c as needed. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: John Rigby <jcrigby@gmail.com>
2009-06-12cpu/mpc512x/diu.c: fix warning: assignment from incompatible pointer typeWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: John Rigby <jcrigby@gmail.com>
2009-06-12cpu/mpc512x/pci.c: minor coding style cleanupWolfgang Denk
Get rid of variable declaration in the middle of the code. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: John Rigby <jcrigby@gmail.com>
2009-06-12mpc512x: Move common files to share them by several boardsWolfgang Denk
We will soon see several new MPC521x based boards added. This patch moves files that are not board specific to a common directory so they can be shared by all such ports. It also splits off common IDE code into a new file, cpu/mpc512x/ide.c . Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: John Rigby <jcrigby@gmail.com>
2009-06-12mpc512x: change cpu/mpc512x/Makefile to use Kconfig styleWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: John Rigby <jcrigby@gmail.com>
2009-06-12General help message cleanupWolfgang Denk
Many of the help messages were not really helpful; for example, many commands that take no arguments would not print a correct synopsis line, but "No additional help available." which is not exactly wrong, but not helpful either. Commit ``Make "usage" messages more helpful.'' changed this partially. But it also became clear that lots of "Usage" and "Help" messages (fields "usage" and "help" in struct cmd_tbl_s respective) were actually redundant. This patch cleans this up - for example: Before: => help dtt dtt - Digital Thermometer and Thermostat Usage: dtt - Read temperature from digital thermometer and thermostat. After: => help dtt dtt - Read temperature from Digital Thermometer and Thermostat Usage: dtt Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-06-12Add support for Linux-like kallsysmsMike Frysinger
The kernel stores address<->symbol names in it so things can be decoded at runtime. Do it in U-Boot, and we get nice symbol decoding when crashing. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-12OMAP3 Turn on the GPIO bank clocksTom Rix
The function and interface clocks for each GPIO bank, except the first, must be explicitly turned on. These are controlled by the config level defines CONFIG_OMAP3_GPIO_n where n is from 2 to 6. Signed-off-by: Tom Rix <Tom.Rix@windriver.com> Acked-by: Dirk Behme <dirk.behme@googlemail.com>
2009-06-12at91: move cpu info print to cpuJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12at91: extract reset from timerJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12omap24xx: rename reset fileJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12lh7a40x: move serial driver to drivers/serialJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12pxa: move serial driver to drivers/serialJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12arm: remove cpu_initJean-Christophe PLAGNIOL-VILLARD
move s3c44b0 to arch_cpu_init and as noone use cpu_init remove it Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12arm: unify interrupt initJean-Christophe PLAGNIOL-VILLARD
all arm init the IRQ stack the same way so unify it in lib_arm/interrupts.c and then call arch specific interrupt init Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12arm: unify linker scriptJean-Christophe PLAGNIOL-VILLARD
all arm boards except a few use the same cpu linker script so move it to cpu/$(CPU) that could be overwrite in following order SOC BOARD via the corresponding config.mk Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12afeb9260: fix macb device initJean-Christophe PLAGNIOL-VILLARD
uses PA10, PA11 for ETX2 and ETX3. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12ppc4xx: Remove PCI async bootup message if PCI is not usedStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2009-06-12ARM DaVinci: Reset with watchdog enabledThomas Lange
Once the Davinci watchdog has been enabled, the timeout value cannot be changed. If the timeout in use is long, it can take a long time for card to reset. By writing an invalid service key, we can trigger an immediate reset. Signed-off-by: Thomas Lange <thomas@corelatus.se>
2009-06-12at91: regroup IP hw init in one file per socJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12OMAP3 Port kernel omap gpio interface.Tom Rix
Port version 2.6.27 of the linux kernel's omap gpio interface to u-boot. The orignal source is in linux/arch/arm/plat-omap/gpio.c See doc/README.omap3 for instructions on use. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-06-12ARM DaVinci:Consolidate common u-boot.ldsSandeep Paulraj
The u-boot.lds is common for all DaVinci boards. The patch removes multiple instances and moves the u-boot.lds to /cpu/arm926ejs/davinci folder. This addresses one of the comments i received while submitting patches for DM3xx Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2009-06-12OMAP Consolidate common u-boot.lds to cpu layer.Tom Rix
The u-boot.lds file is common for all omap boards. Move a cleaned up version to the cpu layer and add makefile logic to use it. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-06-12arm920/926/926: remove non needed headerJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12davinci: display correct clock infoDavid Brownell
Move the clock-rate dumping code into the cpu/.../davinci area where it should have been, enabled by CONFIG_DISPLAY_CPUINFO, updating the format and showing the DSP clock (where relevant). Switch boards to use the cpuinfo() hook for this stuff. Remove a few now-obsolete PLL #defines. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-06-12arm: timer and interrupt init reworkJean-Christophe PLAGNIOL-VILLARD
actually the timer init use the interrupt_init as init callback which make the interrupt and timer implementation difficult to follow so now rename it as int timer_init(void) and use interrupt_init for interrupt btw also remane the corresponding file to the functionnality implemented as ixp arch implement two timer - one based on interrupt - so all the timer related code is moved to timer.c Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12OMAP3: Reorganize Makefile styleJean-Christophe PLAGNIOL-VILLARD
Reformat COBJS handling. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-06-12OMAP3: Remove dublicated interrupt codeJean-Christophe PLAGNIOL-VILLARD
Remove duplicated interrupt code. Original, identical code can be found in lib_arm/interrupts.c Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-06-12at91rm9200: move reset code to reset.cJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12ixp/interrupts: Move conditional compilation to MakefileJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12arm: cleanup remaining CONFIG_INIT_CRITICALJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12arm946es: remove non used timerJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12davinci: add basic dm355/dm350/dm335 supportDavid Brownell
Add some basic declarations for DaVinci DM355/DM350/DM335 support, keyed on CONFIG_SOC_DM355. (DM35X isn't quite right because the DM357 is very different; while the DM355 is like a DM355 without the MPEG/JPEG coprocessor). These have different peripherals than the DM6446, and some of the peripherals are at different addresses. Notably for U-Boot, there's no EMAC, and the NAND controller address is different Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2009-06-12davinci: fix dm644x bugletsDavid Brownell
Fix two buglets in the dm644x support: don't set two must-be-zero bits in the UART management register; and only include the I2C hooks if the I2C driver is being included. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>