summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2008-06-11Merge branch 'master' of git://www.denx.de/git/u-boot-mipsWolfgang Denk
2008-06-10net: Conditional COBJS inclusion of network driversShinya Kuribayashi
Replace COBJS-y with appropriate driver config names. Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-09Merge branch 'master' of git://git.denx.de/u-bootBen Warren
2008-06-06DM9000 fix status check fail 0x6d error for trizeps boardRemy Bohmer
According to the Application Notes of the DM9000, only the 2 bits 0:1 of the status byte need to be checked to identify a valid packet in the fifo But, The several different Application Notes do not all speak the same language on these bits. They do not disagree, but only 1 Application Note noted explicitly that only these 2 bits need to be checked. Even the datasheets do not mention anything about these 2 bits. Because the old code, and the kernel check the whole byte, I left this piece untouched. However, I tested all board/DM9000[A|E|EP] devices with this 2 bit check, so it should work. Notice, that the 2nd iteration through this receive loop (when a 2nd packet is in the fifo) is much shorter now, compared to the older U-boot driver code, so that we can maybe run into a hardware condition now that was never seen before, or maybe was seen very unfrequently. Additionaly added a cleanup of a stack variable. Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-05[MIPS] Update <asm/addrspace.h> headerShinya Kuribayashi
- Fix traditional KSEG names - Replace PHYSADDR with CPHYSADDR Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
2008-06-05Fix order for reading rx-status registers in 32bit mode of DM9000Remy Bohmer
A last minute cleanup before submitting the DM9000A patch series yesterday introduced a bug in reading the rx-status registers in 32bit mode only. This patch repairs this. Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-05DM9000: Some minor code cleanupsRemy Bohmer
Some lines of the U-boot DM9000x driver are longer than 80 characters, or need some other minor cleanup. Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-05DM9000: Make driver work properly for DM9000ARemy Bohmer
The DM9000A network controller does not work with the U-boot DM9000x driver. Analysis showed that many incoming packets are lost. The DM9000A Application Notes V1.20 (section 5.6.1) recommend that the poll to check for a valid rx packet be done on the interrupt status register, not directly by performing the dummy read and the rx status check as is currently the case in the u-boot driver. When the recommended poll is done as suggested the driver starts working correctly on 10Mbit/HD, but on 100MBit/FD packets come in faster so that there can be more than 1 package in the fifo at the same time. The driver must perform the rx-status check in a loop and read and handle all packages until there is no more left _after_ the interrupt RX flag is set. This change has been tested with DM9000A, DM9000E, DM9000EP. Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-05DM9000: Improve eth_reset() routineRemy Bohmer
According to the application notes of the DM9000 v1.22 chapter 5.2 bullet 2, the reset procedure must be done twice to properly reset the DM9000 by means of software. This errata is not needed anymore for the DM9000A, but it does not bother it. This change has been tested with DM9000A, DM9000E, DM9000EP. Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-05DM9000: improve eth_send() routineRemy Bohmer
The eth_send routine of the U-boot DM9000x driver does not match the DM9000 or DM9000A application notes/programming guides. This change improves the stability of the DM9000A network controller. This change has been tested with DM9000A, DM9000E, DM9000EP. Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-05DM9000: repair debug loggingRemy Bohmer
It seems that the debugging code of the DM9000x driver in U-boot has not been compiled for a long time, because it cannot compile... Also rearranged some loglines to get more useful info while debugging. Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-05DM9000: Add data bus-width auto detection.Remy Bohmer
The U-boot DM9000x driver contains a compile time bus-width definition for the databus connected to the network controller. This compile check makes the code unclear, inflexible and is unneccessary. It can be asked to the network controller what its bus-width is by reading bits 6 and 7 of the interrupt status register. The linux kernel already uses a runtime mechanism to determine this bus-width, so the implementation below looks somewhat like that implementation. This change has been tested with DM9000A, DM9000E, DM9000EP. Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-03E1000: Add support for the 82541GI LF Intel Pro 1000 GT Desktop AdapterWolfgang Grandegger
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-03ColdFire: Add 10 base ethernet support for mcf5445xTsiChung Liew
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-05-24Merging Stelian Pop AT91 patchesJean-Christophe PLAGNIOL-VILLARD
Merge branch 'testing-V2' Conflicts: board/atmel/at91cap9adk/Makefile Fixing copyright board/atmel/at91sam9260ek/Makefile Fixing copyright board/atmel/at91sam9260ek/u-boot.lds Delete no more needed ld script Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-24Add Marvell 88E1118 support for TSECRon Madrid
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-05-23smc911x: add 16 bit supportJens Gehrlein
Signed-off-by: Jens Gehrlein <sew_s@tqs.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-05-20Big white-space cleanup.Wolfgang Denk
This commit gets rid of a huge amount of silly white-space issues. Especially, all sequences of SPACEs followed by TAB characters get removed (unless they appear in print statements). Also remove all embedded "vim:" and "vi:" statements which hide indentation problems. Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-05-10AT91SAM9263EK supportStelian Pop
This patch adds support for the AT91SAM9263 chip and the AT91SAM9263EK board. Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10AT91SAM9261EK supportStelian Pop
This patch adds support for the AT91SAM9261 chip and the AT91SAM9261EK board. Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-09Fix @ -> <at> substitutionStelian Pop
When applying the AT91CAP9 patches upstream, something transformed the '@' character into the ' <at> ' sequence. The patch below restores the original form in all the places where it has been modified (the AT91CAP9 files, the AT91SAM9260 files which were copied from AT91CAP9, and a couple of other files where the ' <at> ' sequence was present). Signed-off-by: Stelian Pop <stelian@popies.net>
2008-05-08Fix @ -> <at> substitutionStelian Pop
When applying the AT91CAP9 patches upstream, something transformed the '@' character into the ' <at> ' sequence. The patch below restores the original form in all the places where it has been modified (the AT91CAP9 files, the AT91SAM9260 files which were copied from AT91CAP9, and a couple of other files where the ' <at> ' sequence was present). Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-03drivers/net/tsec.c: Fix typo.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-05-03TSEC: add config options for VSC8601 RGMII PHYAndre Schwarz
The Vitesse VSC8601 RGMII PHY has internal delay for both Rx and Tx clock lines. They are configured using 2 bits in extended register 0x17. Therefore CFG_VSC8601_SKEW_TX and CFG_VSC8601_SKEW_RX have been introduced with valid values 0-3 giving 0.0, 1.4,1.7 and 2.0ns delay. Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Acked-by: Andy Fleming <afleming@freescale.com> Acked-by: Ben Warren <biggerbadderben@gmail.com> -- drivers/net/tsec.c | 6 ++++++ drivers/net/tsec.h | 3 +++ 2 files changed, 9 insertions(+), 0 deletions(-)
2008-04-30ColdFire: Fix ethernet hang issue for mcf547x_8xTsiChung Liew
The ethernet hang is caused by receiving buffer in DRAM is not yet ready due to access cycles require longer time in DRAM. Relocate DMA buffer descriptors from DRAM to internal SRAM. Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-04-29NE2000: Fix regresssion introduced by e710185aae90 on non AX88796Jean-Christophe PLAGNIOL-VILLARD
Move non-inlied functions into specific drivers file Set get_prom as weak Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Vlad Lungu <vlad@comsys.ro> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-04-29minor cs8900 driver clean upGuennadi Liakhovetski
Remove a redundant register definition, clean up some coding style violations. Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-04-28rtl8169: fix compiler warningsGuennadi Liakhovetski
Fix multiple compiler warnings related to argument type mismatch. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
2008-04-28pcnet.c: fix a merge issueWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-04-24NE2000: coding style cleanupJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-04-24Fixed pcnet io_baseVlad Lungu
Bus and phys address are not always the same Signed-off-by: Vlad Lungu <vlad@comsys.ro>
2008-04-24drivers/net/pcnet.c: Coding Style cleanup.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-04-24Added Am79C970A chip id to pcnetVlad Lungu
Signed-off-by: Vlad Lungu <vlad@comsys.ro>
2008-04-18Merge branch 'master' of git://www.denx.de/git/u-boot-netWolfgang Denk
2008-04-17s3c4510b_eth: fix 'packed' attribute ignored for fields of MACFrameJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-04-15Clean up smsc911x driverGuennadi Liakhovetski
Replace direct register address derefencing with accessor functions. Restrict explicitly 32-bit bus-width, extend affected configurations respectively. Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-04-15This patch adds a driver for the following smsc network controllers:Sascha Hauer
LAN9115 LAN9116 LAN9117 LAN9215 LAN9216 LAN9217 Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Guennadi Liakhovetski<lg@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-04-13Coding Style cleanup; update CHANGELOGWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-04-13Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeWolfgang Denk
2008-04-11Revert merge of git://www.denx.de/git/u-boot-arm, commit 62479b18:Wolfgang Denk
Reverting became necessary after it turned out that the patches in the u-boot-arm repo were modified, and in some cases corrupted. This reverts the following commits: 066bebd6353e33af3adefc3404560871699e9961 7a837b7310166ae8fc8b8d66d7ef01b60a80f9d6 c88ae20580b2b01487b4cdcc8b2a113f551aee36 a147e56f03871bba4f05058d5e04ce7deb010b04 d6674e0e2a6a1f033945f78838566210d3f28c95 8c8463cce44d849e37744749b32d38e1dfb12e50 c98b47ad24b2d91f41c09a3d62d7f70ad84f4b7d 8bf69d81782619187933a605f1a95ee1d069478d 8c16cb0d3b971f46fbe77c072664c0f2dcd4471d a574a73852a527779234e73e17e7597fd8128882 1377b5583a48021d983e1fd565f7d40c89e84d63 1704dc20917b4f71e373e2c888497ee666d40380 Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-04-08microblaze: Add Emaclite driver to MakefileMichal Simek
Signed-off-by: Michal Simek <monstr@monstr.eu>
2008-04-08microblaze: Add Emac driver to MakefileMichal Simek
Signed-off-by: Michal Simek <monstr@monstr.eu>
2008-04-08microblaze: add Emac ethernet driverMichal Simek
2008-04-08microblaze: add Emaclite ethernet driverMichal Simek
2008-04-07Merge branch 'master' of git://www.denx.de/git/u-boot-at91Wolfgang Denk
2008-04-07Merge branch 'master' of git://www.denx.de/git/u-boot-netWolfgang Denk
2008-04-01Add Vitesse 8601 support to TSEC driverTor Krill
Add phy_info for Vitesse VSC8601. Add config option, CFG_VSC8601_SKEWFIX, to enable RGMII skew timing compensation. Signed-off-by: Tor Krill <tor@excito.com> Reviewed-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-04-01SPARC: added SMC91111 driver in and out macros for LEON processors.Daniel Hellstrom
This patch makes SPARC/LEON processors able to read and write to the SMC91111 chip using the chip external I/O bus of the memory controller. This patchs defines the standard in and out macros expected by the SMC9111 driver. To access that I/O bus one must set up the memory controller (MCTRL or FTMCTRL) correctly. It is assumed that the user sets up this correctly when the other MCTRL parameters are set up. It can be set up from the board configuration header file. Signed-off-by: Daniel Hellstrom <daniel@gaisler.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-03-31Add support for AT91SAM9260EKStelian Pop
Support for booting from internal DataFlash, external DataFlash card or NAND flash is available. Signed-off-by: Stelian Pop <stelian@popies.net>
2008-03-30add SMSC LAN9x1x Network driverSascha Hauer
This patch adds a driver for the following smsc network controllers: LAN9115 LAN9116 LAN9117 LAN9215 LAN9216 LAN9217 Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
generated by cgit v0.10.2 at 2024-08-18 00:02:16 (GMT)