Age | Commit message (Collapse) | Author |
|
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.
This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip. It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
This typedef serves no purpose other than causing confusion with
struct nand_chip.
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
Commit ad4f54ea86b ("arm: Remove palmtreo680 board") removed the only
user of the docg4 driver and the palmtreo680 image flashing tool. This
patch removes them.
Signed-off-by: Scott Wood <oss@buserror.net>
Cc: Mike Dunn <mikedunn@newsguy.com>
Cc: Simon Glass <sjg@chromium.org>
|
|
This driver is not used by anyone, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Scott Wood <oss@buserror.net>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
Correct the nand ecc initialization code
This fixes the issue of incorrect nand ecc
init if no device is found in ecc_matrix then
it endsup ecc init with junk initialization
instead of the most suited one.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
|
|
The index returned by get_sys_clk_index() is not exactly what we expect.
Let's not rely on that and use get_sys_clk_freq() instead.
This fixes missing USB3 devices in the Linux kernel when USB is started
in u-boot. It still doesn't fix missing USB3 devices in u-boot though.
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
|
The CONFIG_OMAP1510 is no longer defined, so remove this dead code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Nishanth Menon <nm@ti.com>
|
|
The ns16550 driver needs serial_in_shift() and serial_out_shift()
when compiled in debug UART mode, so shift the DM_SERIAL check a
little to make these functions available.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The MXS certainly does not support any sort of networking in GPIO code,
remove the netdev.h header.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add ethernet driver for the AR933x and AR934x Atheros MIPS machines.
The driver could be easily extended to other WiSoCs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Wills Wang <wills.wang@live.com>
[fixed Kconfig dependency]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
If dev->iobase is 64 bits wide then writing the value of the BAR into a
pointer to iobase will not work on big endian systems, where the BAR
value will incorrectly get written to the upper 32 bits of the 64 bit
variable. Fix this by reading the BAR into a u32, matching the type
expected by pci_read_config_dword.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
|
|
Fix the pcnet driver to build safely on 64 bit platforms, in preparation
for allowing MIPS64 builds for Malta boards.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Now that MIPS virt_to_phys can handle kseg1 addresses on MIPS32, stop
manually converting addresses to their kseg0 equivalents in the pcnet
driver.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
|
|
For odroid-c2 (arch-meson) for now disable designware eth as meson
now needs to do some harder GPIO work.
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
lib/efi_loader/efi_disk.c
Modified:
configs/odroid-c2_defconfig
|
|
|
|
When offset is not aligned to page address, it is possible that extra offset
will be read from nand. Adjust the image such that first byte of the image
is at load address after the first page is read.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Detect a FIT when loading from SPI and handle it using the
new FIT SPL support.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
It is pointless to build gadget driver if USB_GADGET is disabled.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
This adds platform code for the Amlogic Meson GXBaby (S905) SoC and a
board definition for ODROID-C2. This initial submission only supports
UART and Ethernet (through the existing Designware driver). DTS files
are the ones submitted to Linux arm-soc for 4.7 [1].
[1] https://patchwork.ozlabs.org/patch/603583/
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
All members of the DMA descriptor must be 32-bit, even on 64-bit
architectures: change the type to u32 to ensure this. Also, fix
other warnings.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Use phys_addr_t not unsigned long long to test that we're within
DMA'able memory]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This small change tidies up the code slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
When these functions are not compiled in, we still need to declare the
correct function signature to avoid a build warnings in SPL. Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Allow driver model to be used for block devices in the rockchip mmc driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add support for using driver model for block devices in this driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Update sdhci.c so that it works with driver model enabled for block devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Enable this option to correct display artifacts when a write-back cache is
in use.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Setup the clocks for the gmac ethernet interface. This assumes the mac
clock is fed by an external clock which is common on RK3288 based
devices.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The rgmii_pins node in rk3288.dtsi configures 15 pins. Increase the size
of the cell array to accomedate that, otherwise only the first 10 get
configured.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add support for the snps,reset-gpio, snps,reset-active-low (optional) and
snps,reset-delays-us device-tree bindings. The combination of these
three define how the PHY should be reset to ensure it's in a sane state.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
A DM driver for PCA953x was recently introduced by Peng Fan, which lacked
support for the 40 GPIO versions.
This patch adds support for these chips.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Peng Fan <van.freenix@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
We don't need an int since no value is over 80. This saves a small amount of
SPL space (about 44 bytes).
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This function is no longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This adds to code size and is not needed, since hang() will print a message.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This adds a sandbox mailbox implementation (provider), a test client
device, instantiates them both from Sandbox's DT, and adds a DM test
that excercises everything.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org> # v1
|
|
A mailbox is a hardware mechanism for transferring small message and/or
notifications between the CPU on which U-Boot runs and some other device
such as an auxilliary CPU running firmware or a hardware module.
This patch defines a standard API that connects mailbox clients to mailbox
providers (drivers). Initially, DT is the only supported method for
connecting the two.
The DT binding specification (mailbox.txt) was taken from Linux kernel
v4.5's Documentation/devicetree/bindings/mailbox/mailbox.txt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The current reset API implements a method to reset the entire system.
In the near future, I'd like to introduce code that implements the device
tree reset bindings; i.e. the equivalent of the Linux kernel's reset API.
This controls resets to individual HW blocks or external chips with reset
signals. It doesn't make sense to merge the two APIs into one since they
have different semantic purposes. Resolve the naming conflict by renaming
the existing reset API to sysreset instead, so the new reset API can be
called just reset.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Now that the DM core sets driver_data before calling bind(), this driver
can make use of driver_data to determine the set of child devices to
create, rather than manually re-implementing the matching logic in code.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
|
|
This will allow a driver's bind function to use the driver data. One
example is the Tegra186 GPIO driver, which instantiates child devices
for each of its GPIO ports, yet supports two different HW instances each
with a different set of ports, and identified by the udevice_id .data
field.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
|
|
If the UART is to be accessed using I/O port accessors (inb & outb) then
using map_physmem doesn't make sense, since it operates in a different
memory space. Remove the call to map_physmem when
CONFIG_SYS_NS16550_PORT_MAPPED is defined, allowing I/O port addresses
to not be mangled by the incorrect mapping.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Support ISA busses in much the same way as Linux does. This allows for
ISA bus addresses to be translated, and only if CONFIG_OF_ISA_BUS is
selected in order to avoid including the code in builds which won't need
it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
|
|
|
|
The A80 uses the AXP809 as its primary PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Adds poweroff support for axp818 pmic.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The AXP818 has a switchable output, SW. This is commonly used for
controlling power to the LCD backlight.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Description said eldo2 instead of fldo2, a copy-paste error.
Fixes: 38491d9c6515 ("power: axp818: Add support for FLDOs")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The ELDO enable bits and registers are contiguous for axp221. Instead
of a switch case testing against the index, just use the index to shift
the bit or register offset.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
|