| Age | Commit message (Collapse) | Author |
|---|
|
add common phy reset code into a common function.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Jens Scharsig <esw@bus-elektronik.de>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Stelian Pop <stelian@popies.net>
Cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Cc: Eric Benard <eric@eukrea.com>
Cc: Markus Hubig <mhubig@imko.de>
Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Tested-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Tested-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
board/compulab/common/Makefile
board/udoo/Makefile
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h
|
|
Get rid of too many ifdeffery in usb ohci driver
Add following two configuration for USB clock selecting
- CONFIG_USB_ATMEL_CLK_SEL_PLLB: using PLLB as usb ohci input clock
- CONFIG_USB_ATMEL_CLK_SEL_UPLL: using UPLL as usb ohci input clock
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Remove platform CONFIG_SYS_HZ definition for configs a-z*.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
In order to use the serial interface on the PortuxG20 we need to enable the
level converter first by setting the PC9 pin to high. The level converter needs
some time to settle so we have to use the mdelay() function to wait for some
time. Unfortunately we have no timers available at board_early_init_f() so we
enable the serial output early within board_postclk_init().
Now the U-Boot output looks fine:
| U-Boot 2012.07-00132-gaf1a3b0-dirty (Aug 16 2012 - 18:21:32)
|
| CPU: AT91SAM9G20
| Crystal frequency: 18.432 MHz
| CPU clock : 396.288 MHz
| Master clock : 132.096 MHz
| DRAM: 64 MiB
| WARNING: Caches not enabled
| NAND: 128 MiB
| In: serial
| Out: serial
| Err: serial
| Net: macb0
| Hit any key to stop autoboot: 0
Signed-off-by: Markus Hubig <mhubig@imko.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
This adds support for the AT91SAM9G20 boards by taskit GmbH.
Both boards, Stamp9G20 and PortuxG20, are integrated in one
file. PortuxG20 is basically a SBC built around the Stamp9G20.
Signed-off-by: Markus Hubig <mhubig@imko.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.deve@googlemail.com>
|
