| Age | Commit message (Collapse) | Author |
|---|
|
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
|
|
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Signed-off-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
|
|
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Add Phytec-i.MX6 SOM with NAND
Support:
- 1GB RAM
- Ethernet
- SPI-NOR Flash
- NAND (1024 MB)
- external SD
- UART
Signed-off-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Custom Board based on MX6 Dual, 1GB RAM and eMMC.
There are two variants of the board with and without
PCIe (ZC5202 and ZC5601).
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
Commit 9262367 moves USB errata workaround into a C file. This
causes compiling error for kmcoge4 and kmlion1. To enable the
errata workaround, define CONFIG_USB_EHCI_FSL in common header.
Signed-off-by: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ed Swarthout <Ed.Swarthout@nxp.com>
Cc: Sriram Dash <sriram.dash@nxp.com>
Fixes: 92623672f9d3 ("fsl: usb: make errata function common for PPC and ARM")
|
|
|
|
DRA72-Evm revC uses dra72-evm-revc.dtb. Update the same in env vatiables.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
As the help message of CONFIG_BOOTDELAY says, CONFIG_BOOTDELAY=-2
means the autoboot with no delay, with no abort check even if
CONFIG_ZERO_BOOTDELAY_CHECK is defined.
To sum up, the autoboot behaves as follows:
[1] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=y
autoboot with no delay, but you can abort it by key input
[2] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
autoboot with no delay, with no check for abort
[3] CONFIG_BOOTDELAY=-1
disable autoboot
[4] CONFIG_BOOTDELAY=-2
autoboot with no delay, with no check for abort
As you notice, [2] and [4] come to the same result, which means we
do not need CONFIG_ZERO_BOOTDELAY_CHECK. We can control all the
cases only by CONFIG_BOOTDELAY, like this:
[1] CONFIG_BOOTDELAY=0
autoboot with no delay, but you can abort it by key input
[2] CONFIG_BOOTDELAY=-1
disable autoboot
[3] CONFIG_BOOTDELAY=-2
autoboot with no delay, with no check for abort
This commit converts the logic as follow:
CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
--> CONFIG_BOOTDELAY=-2
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Christian Riesch <christian.riesch@omicronenergy.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
This recently added board missed the tree-wide migration of
CONFIG_BOOTDELAY.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
|
|
Now I2C is initialized early enough to access FPGA so it supports to
show board info as early as other boot methods.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Get the clocks from FPGA through I2C, if IFC is disabled.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
add DM and DTS support for the at91 based siemens
boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
|
|
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
|
|
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebase on current ToT, don't delete gurnard DTB creation]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
|
|
Rename B&R kwb board to brxre1
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Rename B&R tseries board to brppt1
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The Kona PHY supports an 8-bit wide UTMI interface,
therefore, choose this Kconfig setting.
Signed-off-by: Steve Rae <srae@broadcom.com>
|
|
I still see some defines of this config in board headers. Move them
to defconfigs (+ renaming to CONFIG_HUSH_PARSER) to complete this
migration.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Introduce a meson-gxbb-common.h header file and derive the
configuration for Hardkernel Odroid-C2 board from that.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
|
|
This fixes commit d31e9c575f24f4b7f5f382ccae70d7a86bbc379d ,
which broke booting from SD card on all SoCFPGA boards. The
patch assumes the bootloader partition to be partition 3, at
the end of the SD card, which doesn't make any sense. U-Boot
assumes the bootloader partition is partition 1 or that the
bootloader image is at offset +1 MiB from the start of SD card.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Sylvain Lesne <lesne@alse-fr.com>
|
|
Due to changes in distro environment, ENV_SIZE limit was reached on Dragonboard.
This patch increases environment size to 8KiB.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
|
|
I just did not notice this option had an entry in Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
At first, 256 byte of the head of DRAM space was reserved for some
reasons. However, as the progress of development, it turned out
unnecessary, and it was never used in the end. Move the CPU release
address to leave no space.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
|
|
|
|
Currently DFU is not working.
Adjust CONFIG_SYS_MALLOC_LEN and dfu_alt_info so that we are
able to flash u-boot.imx into the eMMC via dfu using the
following method:
=> dfu 0 mmc 0
In the host PC:
dfu-util -D u-boot.imx -a boot
This is the same approach done in the mx6sl warp board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
The latest version of warp7 board provides the connection of the
WDOG1_B pin to the PMIC.
Program the watchdog to enable the WDOG1_B output which causes
a POR reset.
Based on the imx7dsabresd code.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
enable basic DM/DTS support for the siemens am335x based boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
twister board was not updated after changing
SPL defines, resulting in a broken board.
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
With updated moveconfig.py and an better default, re-generate
the migration of BOOTDELAY to the defconfig.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add proper dtb file name for AM572x-IDK in env.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add initial support for NXP's S32V234 SoC and S32V234EVB board.
The S32V230 family is designed to support computation-intensive applications
for image processing. The S32V234, as part of the S32V230 family, is a
high-performance automotive processor designed to support safe
computation-intensive applications in the area of vision and sensor fusion.
Code originally writen by:
Original-signed-off-by: Stoica Cosmin-Stefan <cosminstefan.stoica@freescale.com>
Original-signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Original-signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Eddy Petrișor <eddy.petrisor@nxp.com>
|
|
Add support for the Broadcom BCM23550 board.
Signed-off-by: Steve Rae <srae@broadcom.com>
|
|
|
|
|
|
Tidy up garbage left by commit bb597c0eeb7e ("common: bootdelay: move
CONFIG_BOOTDELAY into a Kconfig option").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
At this point, this is not referenced from anywhere, so remove it
(but it will be re-added later for a different meaning).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This board is based on Snapper 9G45 which has an Atmel AT91SAM9G45 chip and
128MB of SDRAM. It includes a small LCD, 2xUSB host, SD card, Ethernet and
two UARTs.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[apply CONFIG_BOOTDELAY transition]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
|
|
The kernel can now use DT to reserve memory carveouts and
these areas are now the default for drivers that need reserved
memory, so reserving more here is unneeded and any memory reserved
this way will be wasted.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
|
|
|
|
This patch adds QSPI boot support for LS2080AQDS board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then we can switch to booting from QSPI memory space.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Enable QSPI flash related configure options.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
