summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2014-08-25pcm051: use ti_am335x_common.h configMatwey V. Kornilov
Include general configs/ti_am335x_common.h and drop redundant #defines. Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
2014-08-25ARM: DRA: Enable VTT regulatorLokesh Vutla
DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination and this is controlled by gpio7_11. Configuring gpio7_11. The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards, and left unused on previous boards, so it is safe enough to enable gpio on all DRA7 boards. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-08-25cm-t54: convert to generic boardDmitry Lifshitz
Use generic board setup functions by defining CONFIG_SYS_GENERIC_BOARD. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
2014-08-25SOM: tam3517: convert to generic boardJeroen Hofstee
Cc: Raphael Assenat <raph@8d.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-08-25board/ti/dra7xx: add support for parallel NORpekon gupta
This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM. The Flash device is connected to GPMC controller on chip-select[0] and accessed as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and is CFI compatible. As multiple devices are share GPMC pins on this board, so following board settings are required to detect NOR device: SW5.1 (NAND_BOOTn) = OFF (logic-1) SW5.2 (NOR_BOOTn) = ON (logic-0) /* Active-low */ SW5.3 (eMMC_BOOTn) = OFF (logic-1) SW5.4 (QSPI_BOOTn) = OFF (logic-1) And also set appropriate SYSBOOT configurations: SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */ SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */ SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */ SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */ SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */ SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */ SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */ SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */ Also, following changes are required to enable NOR Flash support in dra7xx_evm board profile:
2014-08-25board/ti/dra7xx: add support for parallel NANDpekon gupta
This patch adds support for x16 NAND device (MT29F2G16AAD) connected to GPMC chip-select[0] on DRA7xx EVM. As GPMC pins are shared by multiple devices, so in addition to this patch following board settings are required for NAND device detection [1]: SW5.9 (GPMC_WPN) = OFF (logic-1) SW5.1 (NAND_BOOTn) = ON (logic-0) /* Active-low */ SW5.2 (NOR_BOOTn) = OFF (logic-1) SW5.3 (eMMC_BOOTn) = OFF (logic-1) SW5.4 (QSPI_BOOTn) = OFF (logic-1) And also set appropriate SYSBOOT configurations SW2.1 (SYSBOOT[0]) = ON (logic-1) /* selects NAND Boot */ SW2.2 (SYSBOOT[1]) = OFF (logic-0) /* selects NAND Boot */ SW2.3 (SYSBOOT[2]) = OFF (logic-0) /* selects NAND Boot */ SW2.4 (SYSBOOT[3]) = OFF (logic-0) /* selects NAND Boot */ SW2.5 (SYSBOOT[4]) = ON (logic-1) /* selects NAND Boot */ SW2.6 (SYSBOOT[5]) = ON (logic-1) /* selects NAND Boot */ SW2.7 (SYSBOOT[6]) = OFF (logic-0) /* reserved */ SW2.8 (SYSBOOT[7]) = OFF (logic-0) /* reserved */ SW3.1 (SYSBOOT[ 8])= ON (logic-1) /* selects SYS_CLK1 speed */ SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */ SW3.3 (SYSBOOT[10])= ON (logic-1) /* wait-pin monitoring = enabled */ SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Addr/Data Muxed */ SW3.5 (SYSBOOT[12])= ON (logic-1) /* device type: Addr/Data Muxed */ SW3.6 (SYSBOOT[13])= ON (logic-1) /* device bus-width: 1(x16) */ SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */ SW3.8 (SYSBOOT[15])= ON (logic-1) /* reserved */ Following changes are required in board.cfg to enable NAND on J6-EVM:
2014-08-25board/ti/am43xx: add support for parallel NANDpekon gupta
This patch adds support for NAND device connected to GPMC chip-select on following AM43xx EVM boards. am437x-gp-evm: On this board, NAND Flash signals are muxed with eMMC, thus at a time either eMMC or NAND can be enabled. Selection between eMMC and NAND is controlled by: (a) Statically using Jumper on connecter (J89) present on board. (a) If Jumper on J89 is NOT used, then selection can be dynamically controlled by driving SPI2_CS0[MUX_MODE=GPIO] pin via software: SPI2_CS0 == 0: NAND (default) SPI2_CS0 == 1: eMMC am43x-epos-evm: On this board, NAND Flash control lines are muxed with QSPI, Thus only one of the two can be used at a time. Selection is controlled by: (a) Dynamically driving following GPIO pin from software GPMC_A0(GPIO) == 0 NAND is selected (default) NAND device (MT29F4G08AB) on these boards has: - data-width=8bits - blocksize=256KB - pagesize=4KB - oobsize=224 bytes For above NAND device, ROM code expects the boot-loader to be flashed in BCH16 ECC scheme for NAND boot, So by default BCH16 ECC is enabled for AM43xx EVMs. Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-08-25board/ti/am335x: update configs for parallel NANDpekon gupta
This patch - consolidate CONFIG_SYS_NAND_xx and CONFIG_SPL_NAND_xx from various configuration files into single file. - update MTD Partition table to match AM335x_EVM DT in linux-kernel - segregate CONFIGs based on different boot modes (like SPL and U-Boot) Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-08-25am335x_evm: Enable CONFIG_SPL_ENV_SUPPORT on EMMC_BOOTTom Rini
When we're using EMMC_BOOT that means we have environment on eMMC so we can make use of CONFIG_SPL_ENV_SUPPORT within Falcon Mode. Signed-off-by: Tom Rini <trini@ti.com>
2014-08-25tseries: Set CONFIG_ENV_IS_NOWHERE for SPL+NANDTom Rini
In the case of SPL on these boards we only need environment for SPL_USBETH, so it's safe to normally use ENV_IS_NOWHERE and SPL+NAND does not support environment today. Cc: Hannes Petermaier <oe5hpm@oevsv.at> Signed-off-by: Tom Rini <trini@ti.com>
2014-08-25TI:armv7: Change CONFIG_SPL_STACK to not be CONFIG_SYS_INIT_SP_ADDRTom Rini
There are times where we may need more than a few kilobytes of stack space. We also will not be using CONFIG_SPL_STACK location prior to DDR being initialized (CONFIG_SYS_INIT_SP_ADDR is still used there) so pick a good location within DDR for this to be. Tested on OMAP4/AM335x/OMAP5/DRA7xx. Signed-off-by: Tom Rini <trini@ti.com>
2014-08-25am335x_evm: Move SPL network definesTom Rini
On am335x_evm we only support USBETH for a networking SPL option so move the rest of the defines under that area as that's the only time we need (and want) environment support here. Signed-off-by: Tom Rini <trini@ti.com>
2014-08-09Merge branch 'u-boot-sunxi/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-08-06Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini
2014-08-01kmp204x: CPU watchdog enabledBoschung, Rainer
The booting of the board is now protected by the CPU watchdog. A failure during the boot phase will end up in board reset. Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-08-01ARM: kirkwood: add mvsdio driverDrEagle
This patch add Marvell kirkwood MVSDIO/MMC driver and enable it for Sheevaplugs and OpenRD boards. Signed-off-by: Gerald Kerma <drEagle@doukki.net> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-07-31sunxi: HYP/non-sec: configure CNTFRQ on all CPUsMarc Zyngier
CNTFRQ needs to be properly configured on all CPUs. Otherwise, virtual machines hoping to find valuable information on secondary CPUs will be disapointed... Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-07-31sunxi: HYP/non-sec: add sun7i PSCI backendMarc Zyngier
So far, only supporting the CPU_ON method. Other functions can be added later. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-07-31sun5i: add USB EHCI settingsHans de Goede
Specific USB EHCI settings to be set for sun5i if CONFIG_USB_EHCI is enabled. Note we don't specify default VBUS gpio pins for sun5i since they vary too much from board to board. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-31sun4i: add USB EHCI settingsHans de Goede
Specific USB EHCI settings to be set for sun4i if CONFIG_USB_EHCI is enabled. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-31sun7i: add USB EHCI settingsRoman Byshko
Specific USB EHCI settings to be set for sun7i if CONFIG_USB_EHCI is enabled. Signed-off-by: Roman Byshko <rbyshko@gmail.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> [hdegoede@redhat.com: Use SUNXI_GPH macro for SUNXI_USB_VBUS#_GPIO] [hdegoede@redhat.com: Add #ifndef SUNXI_USB_VBUS#_GPIO to allow override of the default pins from boards.cfg] Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-07-31sunxi: add general USB settingsRoman Byshko
General configuration settings to be set if CONFIG_USB_EHCI is enabled for an Allwinner aka sunxi SoC. Signed-off-by: Roman Byshko <rbyshko@gmail.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-07-31ahci: provide sunxi SATA driver using AHCI platform frameworkIan Campbell
This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done for sun7i only since I don't have access to any other sunxi platforms with sata included. The PHY setup is derived from the Alwinner releases and Linux, but is mostly undocumented. The Allwinner AHCI controller also requires some magic (and, again, undocumented) DMA initialisation when starting a port. This is added under a suitable ifdef. This option is enabled for Cubieboard, Cubieboard2 and Cubietruck based on contents of Linux DTS files, including SATA power pin config taken from the DTS. All build tested, but runtime tested on Cubieboard2 and Cubietruck only. Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-07-30include: remove CONFIG_SPL/CONFIG_TPL definition in config headersMasahiro Yamada
Now CONFIG_SPL and CONFIG_TPL are defined in Kconfig. Remove the redundant definition in config headers. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2014-07-30kconfig: delete redundant CONFIG_${ARCH} definitionMasahiro Yamada
CONFIG_${ARCH} is defined by Kconfig. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2014-07-30include: define CONFIG_SPL and CONFIG_TPL as 1Masahiro Yamada
We are about to switch to Kconfig in the next commit. But there are something to get done beforehand. In Kconfig, include/generated/autoconf.h defines boolean CONFIG macros as 1. CONFIG_SPL and CONFIG_TPL, if defined, must be set to 1. Otherwise, when switching to Kconfig, the build log would be sprinkled with warning messages like this: warning: "CONFIG_SPL" redefined [enabled by default] Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2014-07-29Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2014-07-28Merge git://www.denx.de/git/u-boot-ppc4xxTom Rini
2014-07-28Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini
2014-07-28Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-07-28Merge branch 'u-boot-sh/rmobile' into 'u-boot-arm/master'Albert ARIBAUD
2014-07-28Merge branch 'u-boot-sunxi/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-07-26Merge branch 'u-boot-microblaze/zynq' into 'u-boot-arm/master'Albert ARIBAUD
2014-07-25ARM: omap: move board specific NAND configs out from ti_armv7_common.hpekon gupta
This patch moves some board specific NAND configs: - FROM: generic config file 'ti_armv7_common.h' - TO: individual board config files using these configs. So that each board can independently set the value as per its design. Following configs are affected in this patch: CONFIG_SYS_NAND_U_BOOT_OFFS: <refer doc/README.nand> CONFIG_CMD_SPL_NAND_OFS: <refer doc/README.falcon> CONFIG_SYS_NAND_SPL_KERNEL_OFFS: <refer doc/README.falcon> CONFIG_CMD_SPL_WRITE_SIZE: <refer doc/README.falcon> This patch also updates documentation for few of above NAND configs. Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-07-25ARM: omap: clean redundant PISMO_xx macros used in OMAP3pekon gupta
PISMO_xx macros were used to define 'Platform Independent Storage MOdule' related GPMC configurations. This patch - Replaces these OMAP3 specific macros with generic CONFIG_xx macros as provided by current u-boot infrastructure. - Removes unused redundant macros, which are no longer required after merging of common platform code in following commit commit a0a37183bd75e74608bc78c8d0e2a34454f95a91 ARM: omap: merge GPMC initialization code for all platform +-----------------+-----------------------------------------------------------+ | Macro | Reason for removal | +-----------------+-----------------------------------------------------------+ | PISMO1_NOR_BASE | duplicate of CONFIG_SYS_FLASH_BASE | +-----------------+-----------------------------------------------------------+ | PISMO1_NAND_BASE| duplicate of CONFIG_SYS_NAND_BASE | +-----------------+-----------------------------------------------------------+ | PISMO1_ONEN_BASE| duplicate of CONFIG_SYS_ONENAND_BASE | +-----------------+-----------------------------------------------------------+ | PISMO1_NAND_SIZE| GPMC accesses NAND device via I/O mapped registers so | | | configuring GPMC chip-select for smallest allowable | | | segment (GPMC_SIZE_16M) is enough. | +-----------------+-----------------------------------------------------------+ | PISMO1_ONEN_SIZE| OneNAND uses a fixed GPMC chip-select address-space of | | | 128MB (GPMC_SIZE_128M) | +-----------------+-----------------------------------------------------------+ +-----------------+-----------------------------------------------------------+ | PISMO1_NOR | Unused Macros | | PISMO1_NAND | | | PISMO2_CS0 | | | PISMO2_CS1 | | | PISMO1_ONENAND | | | PISMO2_NAND_CS0 | | | PISMO2_NAND_CS1 | | | PISMO1_NOR_BASE | | | PISMO1_NAND_BASE| | | PISMO2_CS0_BASE | | +-----------------+-----------------------------------------------------------+ Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-07-25ARM: omap: fix GPMC address-map size for NAND and NOR devicespekon gupta
Fixes commit a0a37183bd75e74608bc78c8d0e2a34454f95a91 ARM: omap: merge GPMC initialization code for all platform 1) NAND device are not directly memory-mapped to CPU address-space, they are indirectly accessed via following GPMC registers: - GPMC_NAND_COMMAND_x - GPMC_NAND_ADDRESS_x - GPMC_NAND_DATA_x Therefore from CPU's point of view, NAND address-map can be limited to just above register addresses. But GPMC chip-select address-map can be configured in granularity of 16MB only. So this patch uses GPMC_SIZE_16M for all NAND devices. 2) NOR device are directly memory-mapped to CPU address-space, so its address-map size depends on actual addressable region in NOR FLASH device. So this patch uses CONFIG_SYS_FLASH_SIZE to derive GPMC chip-select address-map size configuration. Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-07-25board: k2e-evm: add board supportHao Zhang
This patch adds Keystone2 k2e_evm evaluation board support. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25ARM: keystone2: clock: add K2E clock supportHao Zhang
This patch adds clock definitions and commands to support Keystone2 K2E SOC. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25configs: k2hk_evm: config: add common EVM configuration headerHao Zhang
This patch adds a common config header file for all the Keystone II EVM platforms. It combines a lot of general definitions in one file. The common header included in the EVM should be specific configuration header. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25ARM: keystone2: move K2HK board files to common KS2 board directoryHao Zhang
This patch moves K2HK board directory to a common Keystone II board directory. The Board related common functions are moved to a common keystone board file. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25k2hk: use common KS2_ prefix for all hardware definitionsKhoronzhuk, Ivan
Use KS2_ prefix in all definitions, for that replace K2HK_ prefix and add KS2_ prefix where it's needed. It requires to change names also in places where they're used. Align lines and remove redundant definitions in kardware-k2hk.h at the same time. Using common KS2_ prefix helps resolve redundant redefinitions and adds opportunity to use KS2_ definition across a project not thinking about what SoC should be used. It's more convenient and we don't need to worry about the SoC type in common files, hardware.h will think about that. The hardware.h decides definitions of what SoC to use. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25ARM: omap: tao3530: Convert to generic boardStefan Roese
Use generic board setup functions by defining CONFIG_SYS_GENERIC_BOARD. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Tom Rini <trini@ti.com>
2014-07-25tricorder: convert to generic boardAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Thomas Weber <thomas.weber@corscience.de>
2014-07-25k2hk_evm: add script to automate NAND flash processKhoronzhuk, Ivan
Add script to automate NAND flash process. As for now the board has two burn scripts - burn to boot from SPI NOR flash and burn to boot from AEMIF NAND flash, rename burn_uboot script to burn_uboot_spi. Also update README to contain NAND burn U-boot process description. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Acked-by: Murali Karicheri <m-karicheri2@ti.com>
2014-07-25mtd: nand: davinci: add opportunity to write keystone U-boot imageKhoronzhuk, Ivan
The Keystone SoCs use the same NAND driver as Davinci. This patch adds opportunity to write Keystone U-boot image to NAND device using appropriate RBL ECC layout. This is needed only if RBL boots U-boot from NAND device and that's supposed that raw u-boot partition is used only for writing image. The main problem is that default Davinci ECC layout is different from Keystone RBL layout. To read U-boot image the RBL needs that image was written using RBL ECC layout. The BBT table is written using default Davinci layout and has to be updated using one. The BBT can be updated only while erasing chip or by forced bad block assigning, so erase function has to use native ecc layout in order to be able to write BBT correctly. So if we're writing to NAND U-boot address we use RBL layout for others we use default ECC layout. Also remove definition for CONFIG_CMD_NAND_ECCLAYOUT as there is no reasons to use ECC layout commands. It was added by mistake. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25tps65218/am43xx_evm: Add power framework support to TPS65218Tom Rini
Add in an init function for the drivers/power framework so we can dump and read the registers via i2c. Cc: Łukasz Majewski <l.majewski@samsung.com> Signed-off-by: Tom Rini <trini@ti.com>
2014-07-25board: Add CONFIG_SYS_GENERIC_BOARD to all gdsys boardsDirk Eibach
Add the generic board infrastructure to all gdsys boards. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
2014-07-24arm: rmobile: Add support Alt boardNobuhiro Iwamatsu
The alt board has R8A7794, 1GB DDR3-SDRAM, USB, Ethernet, QSPI, MMC, SDHI and more. This commit supports the following functions: - DDR3-SDRAM - SCIF - I2C - Ethernet - QSPI Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-07-23board/freescale: use generic board architecture for t2080qds and t2080rdbShengzhou Liu
Tested with NOR boot and NAND boot on T2080QDS and T2080RDB. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2014-07-23ARM: zynq: Enable generic board for Xilinx ZynqMichal Simek
Enable CONFIG_SYS_GENERIC_BOARD for all Zynq boards. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Masahiro Yamada <yamada.m@jp.panasonic.com> [on ZC706 board]
generated by cgit v0.10.2 at 2024-09-19 17:24:35 (GMT)