summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2014-01-10zynq: zc70x: Add Catalyst 24WC08 EEPROM config supportJagannadha Sutradharudu Teki
Adds configurations for Catalyst 24WC08 EEPROM, which is present on the zynq boards. Enable EEPROM support for zc70x boards. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10zynq-common: Define exact TEXT_BASEJagannadha Sutradharudu Teki
Defined TEXT_BASE for u-boot starts from 0x4000000 w.r.t zynq memory-map. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10zynq: Move CONFIG_SYS_SDRAM_SIZE to pre-board configsJagannadha Sutradharudu Teki
CONFIG_SYS_SDRAM_SIZE is specific to a board hence moved to specific pre-config board files. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10zynq: Add zynq zed board supportJagannadha Sutradharudu Teki
Zed is a complete development board based on the Xilinx Zynq-7000 All Programmable SoC. APSOC: - XC7Z020-CLG484-1 Memory: - 512 MB DDR3 - 256 Mb Quad-SPI Flash( - Full size SD/MMC card cage Connectivity: - 10/100/1000 Ethernet - USB OTG (Device/Host/OTG) - USB-UART Expansion: - FMC (Low Pin Count) - Pmod. headers (2x6) Video/Display: - HDMI output (1080p60 + audio) - VGA connector - 128 x 32 OLED - User LEDs (9) User inputs: - Slide switches (8) - Push button switches (7) Audio: - 24-bit stereo audio CODEC - Stereo line in/out - Headphone - Microphone input Analog: - Xilinx XADC header - Supports 4 analog inputs - 2 Differential / 4 Single-ended Debug: - On-board USB JTAG programming port - ARM Debug Access Port (DAP) For more info - http://zedboard.org/product/zedboard Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10zynq: Add zynq zc70x board supportJagannadha Sutradharudu Teki
The Zynq-7000 APSOC zc702 and zc706 enabled complte embedded processing includes ASIC and FPGA design. ZC702-: APSOC: - XC7Z020-CLG484-1 Memory: - DDR3 Component Memory 1GB - 16MB Quad SPI Flash - IIC - 1 KB EEPROM Connectivity: - Gigabit Ethernet GMII, RGMII and SGMII. - USB OTG - Host USB - IIC Bus Headers/HUB - 1 CAN with Wake on CAN - USB-UART Video/Display: - HDMI Video OUT - 8X LEDs Control & I/O: - 3 User Push Buttons - 2 User Switches - 8 User LEDs For more info on zc702 board: - http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC702-G.htm ZC706-: APSOC: - XC7Z045 FFG900 -2 AP SoC Memory: - DDR3 Component Memory 1GB (PS) - DDR3 SODIM Memory 1GB (PL) - 2X16MB Quad SPI Flash (dual parallel) - IIC - 1 KB EEPROM Connectivity: - PCIe Gen2x4 - SFP+ and SMA Pairs - GigE RGMII Ethernet (PS) - USB OTG 1 (PS) - Host USB - IIC Bus Headers/HUB (PS) - 1 CAN with Wake on CAN (PS) - USB-UART Video/Display: - HDMI 8 color RGB 4.4.4 1080P-60 OUT - HDMI IN 8 color RGB 4.4.4 Control & I/O: - 2 User Push Buttons/Dip Switch, 2 User LEDs - IIC access to GPIO - SDIO (SD Card slot) - 3 User Push Buttons, 2 User Switches, 8 User LEDs For more info on zc706 board: - http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC706-G.htm Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10zynq-common: Rename zynq with zynq-commonJagannadha Sutradharudu Teki
zynq.h -> zynq-common.h, zynq-common is Common configuration options for all Zynq boards. zynq.h is no longer exists hense removed from boards.cfg Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10zynq: Add GEM0, GEM1 configs supportJagannadha Sutradharudu Teki
Zynq ethernet controller support two GEM's like CONFIG_ZYNQ_GEM0 and CONFIG_ZYNQ_GEM1 enabled both so-that the respective board will define these macros based on their usage. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10zynq: Add UART0, UART1 configs supportJagannadha Sutradharudu Teki
Zynq uart controller support two serial ports like CONFIG_ZYNQ_SERIAL_UART0 and CONFIG_ZYNQ_SERIAL_UART1 enabled both so-that the respective board will define these macros based on their usage. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10zynq: Enable cache optionsJagannadha Sutradharudu Teki
- Enable cache command - Turn-off L2 cache - Turn-on D-cache Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10zynq: Minor config cleanupJagannadha Sutradharudu Teki
Cleanups mostly on: - Add comments - Re-order configs - Remove #define CONFIG_ZYNQ_SDHCI Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10zynq: Cleanup on memory configsJagannadha Sutradharudu Teki
Cleanup on memory configuration options: - Add comment - Re-order configs Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10zynq: Cleanup on miscellaneous configsJagannadha Sutradharudu Teki
Cleanup on miscellaneous configurable options: - Rename SYS_PROMPT as "zynq-uboot" - Add comment - Re-order configs Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10zynq: Enable Boot FreeBSD/vxWorksJagannadha Sutradharudu Teki
This enabled Boot FreeBSD/vxWorks from an ELF image support Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-10zynq: Enable CONFIG_FIT_VERBOSEJagannadha Sutradharudu Teki
Enabled fit_format_{error,warning}() Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-09arm64: board support of vexpress_aemv8aDavid Feng
Signed-off-by: David Feng <fenghua@phytium.com.cn> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
2014-01-09arm64: core supportDavid Feng
Relocation code based on a patch by Scott Wood, which is: Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: David Feng <fenghua@phytium.com.cn>
2014-01-09add weak entry definitionDavid Feng
Signed-off-by: David Feng <fenghua@phytium.com.cn>
2014-01-08Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-01-07arm: omap: cm_t35: enable gpio bank 5 clocks explicitlyNikita Kiryanov
Following commit "arm: omap3: Enable clocks for peripherals only if they are used" (f33b9bd3984fb11e1d8566a866adc5957b1e1c9d) it is now necessary to enable clocks for GPIO banks explicitly. On cm_t35, GPIO bank 5 is necessary for scf0403 lcd support. Enable GPIO bank 5 clocks. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2014-01-07ARM: twister: add missing gpio clock initJeroen Hofstee
Commit f33b9bd3984fb11e1d8566a866adc5957b1e1c9d breaks boards which do not explicitly enable the gpio clocks. This causes the twister spl to hang, since it uses the no longer enabled gpio 55. Add CONFIG_OMAP3_GPIO_2 to unbrick the board. Cc: Stefano Babic <sbabic@denx.de> Cc: Tapani Utriainen <tapani@technexion.com> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Acked-by: Stefano Babic <sbabic@denx.de>
2014-01-07ARM: tam3517-common: fix nand spl bootJeroen Hofstee
commit f9095aac793aa8917ab9b915c5d449e6dc8d3d30, "mtd: nand: omap: add CONFIG_NAND_OMAP_ECCSCHEME for selection of ecc-scheme" removed CONFIG_SPL_NAND_SOFTECC from the tam3517 common config, causing the spl nand boot to fail. Add it back, so derived boards boot again. Cc: Pekon Gupta <pekon@ti.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Raphael Assenat <raph@8d.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tapani Utriainen <tapani@technexion.com> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Acked-by: Stefano Babic <sbabic@denx.de>
2014-01-07TI:omap3: Drop omap3_zoom2Tom Rini
The omap3_zoom2 board has not been updated for a correct CONFIG_SYS_HZ and Tom Rix's email has long been bouncing. Signed-off-by: Tom Rini <trini@ti.com>
2014-01-07cam_enc_4xx: Set CONFIG_SYS_NAND_MAX_OOBFREE / CONFIG_SYS_NAND_MAX_ECCPOSTom Rini
With the changes to make OOBFREE/ECCPOS configurable but default to larger, we need to set these config options for the space savings they provide. Cc: Scott Wood <scottwood@freescale.com> Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
2014-01-06arm/km: fix i2c mux define for km_kirkwood_128m16 targetHolger Brunck
Due to the i2c mux rework in u-boot we now have only to specify the busnumber and not the whole mux configuration. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Heiko Schocher <hs@denx.de>
2014-01-06arm/km: add support for km_kirkwood_128m16 boardKarlheinz Jerg
The board is similar to the standard km_kirkwood board. From a u-boot point of view, the only difference is an increased 256 MiB DRAM (128M16). A board based on this design is for example the SUP12. Signed-off-by: Karlheinz Jerg <karlheinz.jerg@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2014-01-06kirkwood: ib62x0: use device tree and update configLuka Perkov
Signed-off-by: Luka Perkov <luka@openwrt.org> CC: Prafulla Wadaskar <prafulla@marvell.com> Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
2014-01-06Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-01-06Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
Conflicts: include/micrel.h The conflict above was trivial, caused by four lines being added in both branches with different whitepace.
2014-01-03ARM: mx6: Change the FDT loading address to avoid overlapingOtavio Salvador
This patch fixes allow for the DeviceTree and initrd relocation fixing the boot of FSL 3.10.9-1.0.0-alpha kernel. This changes following boards: - mx6sabreauto - mx6sabresd - wandboard - udoo - nitrogen6x - cgtqmx6eval The reasoning, as explained by Hui Liu, is: ,---- | The FDT blob will be placed at DDR physical addr: 0x11000000. When Linux kernel | Boot up, it will decompress the compressed kernel image and place the decompressed | kernel image at the low end of the DDR memory and start running from it. If the | decompressed kernel image is bigger for example than 16M, it may over written the | fdt blob which u-boot loaded to the DDR memory @0x11000000 with fdt_addr=0x11000000 | | To expand the fdt_addr from 0x11000000 to 0x18000000, which can avoid the override | Since we will not likely have one kernel image larger than 128MB. `---- Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Stefano Babic <sbabic@denx.de>
2014-01-03mx28evk: Extend environment to easy write of NAND systemOtavio Salvador
This adds following new targets: - update_nand_kernel - update_nand_fdt - update_nand_filesystem and to avoid confusion, the 'update_nand_full' has been renamed to 'update_nand_firmware_full'. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-01-03mx28evk: Add 'nandboot' environment commandOtavio Salvador
This reads the kernel, ftd and boot into ubifs filesystem. While on that, the SD firmware filename definition has been moved next to the other SD related commands. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-03mx28evk: Use 512k for fdt partition to align itOtavio Salvador
Using 512k for fdt partition allow it to be aligned with the other small partitions and 512k erase block size. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Stefano Babic <sbabic@denx.de>
2014-01-02mx6: soc: Add the required LDO ramp up delayFabio Estevam
When changing LDO voltages we need to wait for the required amount of time for the voltage to settle. Also, as the timer is still not available when arch_cpu_init() is called, we need to call it later at board_postclk_init() phase. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-02mx6sabre_common.h: Add CONFIG_CMD_FUSE supportFabio Estevam
Add CONFIG_CMD_FUSE option, so that the fuse API can be used. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-12-31board:trats2: fix default partitions and mmc envPiotr Wilczek
This patch add uuid disk to defualt partions necessary to restore gpt partitions and fixes mmcdev environmental variable. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-30SPL: EXYNOS: Prepare for variable size SPL supportRajeshwari Birje
When variable size SPL is used, the BL1 expects the SPL to be encapsulated differently: instead of putting the checksum at a fixed offset in the SPL blob, prepend the blob with a header including the size and the checksum. The enhancements include - adding a command line option, '--vs' to indicate the need for the variable size encapsulation - padding the fixed size encapsulated blob with 0xff instead of random memory contents - do not silently truncate the input file, report error instead - no need to explicitly closing files/freeing memory, this all happens on exit; removing cleanups it makes code clearer - profuse commenting - modify Makefile to allow enabling the new feature per board Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-30Config: Add initial config for SMDK5420Rajeshwari Birje
Adding initial config for SMDK5420 to build and boot U-Boot over Exynos based SMDK5420. Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-30Exynos5420: Add base patch for SMDK5420Rajeshwari Birje
Adding the base patch for Exynos based SMDK5420. This shall enable compilation and basic boot support for SMDK5420. Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-30EXYNOS5: Create a common board fileRajeshwari Birje
Create a common board.c file for all functions which are common across all EXYNOS5 platforms. exynos_init function is provided for platform specific code. Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-19ARM: AM43XX: board: add support for reading onboard EEPROMSekhar Nori
Add support for reading onboard EEPROM to enable board detection. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-19ARM: AM43xx: Add extra ENV settingsLokesh Vutla
Add Extra env settings. This is derived from am335x Extra ENV settings. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-19ARM: AM43xx: Add L2 SupportLokesh Vutla
AM4372 uses PL310 L2 Cache. Enable the configs for the same. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-19ARM: AM43xx: Adapt to ti_armv7_common.h config fileLokesh Vutla
Use ti_armv7_common.h config file to inclde the common configs. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-19arm: omap3: Fix beagleboard SPL boot hangup (GPIO clocks not enabled)Stefan Roese
Patch f33b9bd3 [arm: omap3: Enable clocks for peripherals only if they are used] breaks SPL booting on Beagleboard. Since some gpio input's are read to detect the board revision. But with this patch above, the clocks to the GPIO subsystems are not enabled per default any more. The GPIO banks need to be configured specifically now. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Michael Trimarchi <michael@amarulasolutions.com>
2013-12-18Merge remote-tracking branch 'u-boot-pxa/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-12-18Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-12-18ARM: pxa: Fix CONFIG_SYS_HZ on PXAMarek Vasut
The PXA incorrectly uses CONFIG_SYS_HZ, which should be 1000 across U-Boot. Fix this. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2013-12-18ARM: tegra: Add the Tamonten™ NG Evaluation Carrier boardAlban Bedel
Add support for the new Tamonten™ NG platform from Avionic Design. Currently only I2C, MMC, USB and ethernet have been tested. Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-12-18ARM: config: USB: Tegra30/114: Fix EHCI timeout issue on "bootp"Jim Lin
Fix the timeout issue after running "bootp" command in u-boot console. For example you see "EHCI timed out on TD- token=0x...". TXFIFOTHRES bits of TXFILLTUNING register should be set to 0x10 after a controller reset and before RUN bit is set (per technical reference manual). Signed-off-by: Jim Lin <jilin@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-12-18arm: pxa: update LP-8x4x to boot DT kernelSergei Ianovich
DT kernel requires CONFIG_OF_LIBFDT. 'bootm' needs to know DT location. In addition, fix kernel console device and enable U-Boot long help. Signed-off-by: Sergei Ianovich <ynvich@gmail.com> CC: Marek Vasut <marex@denx.de>
generated by cgit v0.10.2 at 2024-08-21 05:18:14 (GMT)