| Age | Commit message (Collapse) | Author |
|---|
|
Move common functions from cmd_nand.c (for calculating offset
and size from cmdline paramter) to common place, so they could
used from other commands which use mtd partitions.
For onenand the arg_off_size() is left in common/cmd_onenand.c.
It should use now the common arg_off() function, but as I could
not test onenand I let it there ...
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
|
|
Enable Driver Model SPI for ls1021atwr board.
DSPI and QSPI only be enabled when boot from QSPI.
DSPI and QSPI are compatible under Driver Model SPI.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
Enable Driver Model SPI for ls1021aqds board.
DSPI and QSPI is enabled only when boot from QSPI.
DSPI and QSPI are compatible under Driver Model SPI.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
|
|
By default on this platform, u-boot loads data into high memory
in the range of 0x7Fxxxxxx, which generates a data abort when the
kernel tries to read it. Config the u-boot environment to load
the device tree and initrd image into lower memory to make them
accessible to the kernel.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
|
|
NAND memory"
This reverts commit f76eba38b3eda905ff3bdc18dd1240d3dcbc6e5a.
This patch did not have a full and proper copyright/S-o-b chain.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Conflicts:
include/configs/sun6i.h
include/configs/sun8i.h
|
|
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.
Remove the configs that behave this way from the archs.
A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:
SPIFLASH
DISPLAY_BOARDINFO
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
Update new naming scheme.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
rastaban is a draco version with more flash, more RAM
and faster CPU. Number of partitions is the same but
rootfs partition is different.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
BeagleBoard-X15 uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
add cpsw ethernet boot mode support to download spl and
u-boot.img via tftp protocol. Also adding a seperate config
for ethernet boot mode as the default build falcon mode and
environment on MMC is defined for ethernet boot mode
environment should be set to nowhere.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
While booting via usb host mode, ROM uses DMA to copy MLO over USB so
ARM internal RAM cannot be used. Adding USB host boot support by
introducing new config target which sets SPL_TEXT_BASE to OCMC ram.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
With 1.2 silicon this is now the documented starting usable point for
downloading images to (and corrects a problem with peripheral booting
with prior silicon). Prior silicon is OK using this address as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
|
|
now in ti_armv7_common.h
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Tested on Pandaboard (rev. A3) and Beagleboard xM (rev. B).
Compilation tested on TI armv7 boards and OMAP boards from other vendors.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
updates for the siemens am335x based boards:
- draco: add delay for DDR3 configuration
- change MTD partition layout and add a possibility
to redefine MTD layout in board header.
- move ubi support to common header file
- draco: improve dtb naming
- draco: set CONFIG_SYS_CBSIZE to 1024
- add generic env based led
Leds can now be defined in Environment
- add generic env based dfu button
Which gpio is used for the dfu button can be defined
through the Environment
- set MACH_TYPE only if defined
- draco: increase CPU freq to 300MHz
- Add time command to siemens am33xx boards
- DDR3: increase default tRFC
- draco: enable pullup for DFU and ERST pin
- change print format DDR3
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
There is no harm in declaring the function prototypes even if nothing
implements them, and when CONFIG_DM_USB=y the various usb functions are
available regardless of any controller drivers being enabled.
This fixes compile warnings due to missing prototypes on ARCHs where
the ARCH Kconfig always enables CONFIG_DM_USB and various usb drivers.
One could argue that in the case of no controllers CONFIG_DM_USB should not
be set, but this problem is typically seen during bringup of boards which
do actually have usb controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
With the change to make sure that CONFIG_CMD_NET is enabled this board
no longer fits into the linker script:
powerpc-linux-ld.bfd: section .resetvec loaded at [fffffffc,ffffffff] overlaps section .u_boot_list loaded at [ffffff58,00000723]
powerpc-linux-ld.bfd: u-boot: section .resetvec lma 0xfffffffc adjusted to 0x724
powerpc-linux-ld.bfd: u-boot: section `.resetvec' can't be allocated in segment 0
LOAD: .data.init .text .rodata .reloc .data .u_boot_list .resetvec
powerpc-linux-ld.bfd: final link failed: File truncated
Drop CONFIG_SYS_LONGHELP to free up space.
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
since we have now various processor-speeds it isn't useful anymore to
preinitialize kernels-delay loop.
Rather we want the kernel to calibrate it on every boot.
This wastes around 80ms boottime but is compatible to all CPU-speeds.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
Currently there is no default value for NETARGS if CONFIG_CMD_NET=y isn't set.
This results in build errors which was first discovered when trying to run
make env.
By defining a blank NETARGS these errors can be avoided.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Tested-by: Maxin B. John <maxin.john@enea.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Since the tam3517 base board has a 16bit wide nand connected to
the gpmc, enable the prefetch mode, since that is now supported.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: pekon gupta <pekon@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
|
|
In the cases where we make use of environment in SPL we do not need
these defaults compiled in and available. These are taking up space
that in some cases now prevent linking, so drop.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Vision Systems's Baltos is based on AM335x SoC
from Texas Instruments. This patch adds support
such Industrial PCs in mainline u-boot.
[ balbi@ti.com: updated original patch to current u-boot ]
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Now all the AVR32 boards have been converted into Generic Board.
Select it in Kconfig and clean up defines in header files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
On AM437x-GP Evm there is 2GB of DDR3 memory available as stated in
AM437x GP EVM HardwareUser's guide http://www.ti.com/lit/ug/spruhw7/spruhw7.pdf.
But MAX_RAM_BANK_SIZE is defined as 1GB.
Fixing MAX_RAM_BANK_SIZE to 2GB on AM43xx.
Reported-by: Shivasharan Nagalikar <shivasharan.nagalikar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Enable booting from NAND on the am437xx-evm.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Use the correct partition names from with the Device Tree blob
and the kernel is picked up. Also use partition name instead of
number for the root filesystem in the kernel boot arguments.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
We almost always use UBIFS for user accessible NAND file systems and
the UBIFS file system might contain more than one volume within the
single NAND partition. The last NAND partition is therefore more
appropriately named as "NAND.file-system" instead of "NAND.rootfs"
The Linux kernel (as of v3.16) also uses "NAND.file-system" to name the
last NAND partition. This patch makes the partition name consistent
between u-boot and the kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Enable full 48-bit LBA48 data reads by passing the upper word of the
LBA block pointer in bytes 9 and 10 of the FIS.
This allows uboot to load data from any arbitrary sector on a drive
with 2 or more TB of available data connected to an AHCI controller.
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com>
Signed-off-by: Andre Przywara <osp@andrep.de>
[trini: Make use of CONFIG_SYS_64BIT_LBA in a few places to drop
warnings on platforms that don't enable that feature ]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Enable IO delay recalibration sequence.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Enabling IO delay recalibration sequence for DRA7 EVM.
UART and I2C are configured before IO delay recalibration sequence
as these are used earlier and safe to use.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Drop the code that doesn't use driver model for USB.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this over to Kconfig and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Allow SPL to be built with this option so that we can support device tree
control. Disable the simple bus for now in SPL. It may be needed later.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This option is used by some boards, so support it with driver model. This
is really ugly - we should rewrite this driver once all users are moved to
driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We try to avoid typedefs and these ones are easy enough to remove. Before
changing this header in the next patch, remove the typedefs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This function is used before jumping to U-Boot, but in that case we don't
always want to disable caches.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
|
|
For secure boot systems it is common to have a read-only U-Boot which starts
the machine and jumps to a read-write U-Boot for actual booting the OS. This
allows the read-write U-Boot to be upgraded without risk of permanently
bricking the machine. In the event that the read-write U-Boot is corrupted,
the read-only U-Boot can detect this with a checksum and boot into a
recovery flow.
To support this, add a way to detect when U-Boot is run from SPL as opposed
to some other method, such as booted directly (no SPL) or started from
another source (e.g. a primary U-Boot). This works by putting a special value
in r0.
For now we rely on board-specific code to actually check the register and
set a flag. At some point this could be generalised, perhaps by using a spare
register and passing a flag to _main and/or board_init_f().
This commit does not implement any feature, but merely provides the API for
boards to implement.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add the legacy i2c_reg_read/write() functions to the compatibility layer
so that they can be used when CONFIG_DM_I2C_COMPAT is defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
|
|
Due to absence of CONFIG_SYS_64BIT_LBA, u-boot-sunxi currently has
no support for the (GPT) partioning scheme of large disks > 2TB.
While the AHCI driver seems to handle this nicely, the problem is
that lbaint_t values get truncated to 32-bit.
This patch sets CONFIG_SYS_64BIT_LBA from sunxi_common.h for all
SoCs that support AHCI (CONFIG_SUNXI_AHCI).
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
|
|
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
