path: root/board/ti/evm/evm.c

/*
 * (C) Copyright 2004-2011
 * Texas Instruments, <www.ti.com>
 *
 * Author :
 *	Manikandan Pillai <mani.pillai@ti.com>
 *
 * Derived from Beagle Board and 3430 SDP code by
 *	Richard Woodruff <r-woodruff2@ti.com>
 *	Syed Mohammed Khasim <khasim@ti.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */
#include <common.h>
#include <dm.h>
#include <ns16550.h>
#include <netdev.h>
#include <asm/io.h>
#include <asm/arch/mem.h>
#include <asm/arch/mux.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/gpio.h>
#include <i2c.h>
#include <twl4030.h>
#include <asm/mach-types.h>
#include <asm/omap_musb.h>
#include <linux/mtd/nand.h>
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
#include <linux/usb/musb.h>
#include "evm.h"

#ifdef CONFIG_USB_EHCI_HCD
#include <usb.h>
#include <asm/ehci-omap.h>
#endif

#define OMAP3EVM_GPIO_ETH_RST_GEN1 64
#define OMAP3EVM_GPIO_ETH_RST_GEN2 7

DECLARE_GLOBAL_DATA_PTR;

static const struct ns16550_platdata omap3_evm_serial = {
	.base = OMAP34XX_UART1,
	.reg_shift = 2,
	.clock = V_NS16550_CLK,
	.fcr = UART_FCR_DEFVAL,
};

U_BOOT_DEVICE(omap3_evm_uart) = {
	"ns16550_serial",
	&omap3_evm_serial
};

static u32 omap3_evm_version;

u32 get_omap3_evm_rev(void)
{
	return omap3_evm_version;
}

static void omap3_evm_get_revision(void)
{
#if defined(CONFIG_CMD_NET)
	/*
	 * Board revision can be ascertained only by identifying
	 * the Ethernet chipset.
	 */
	unsigned int smsc_id;

	/* Ethernet PHY ID is stored at ID_REV register */
	smsc_id = readl(CONFIG_SMC911X_BASE + 0x50) & 0xFFFF0000;
	printf("Read back SMSC id 0x%x\n", smsc_id);

	switch (smsc_id) {
	/* SMSC9115 chipset */
	case 0x01150000:
		omap3_evm_version = OMAP3EVM_BOARD_GEN_1;
		break;
	/* SMSC 9220 chipset */
	case 0x92200000:
	default:
		omap3_evm_version = OMAP3EVM_BOARD_GEN_2;
       }
#else /* !CONFIG_CMD_NET */
#if defined(CONFIG_STATIC_BOARD_REV)
	/* Look for static defintion of the board revision */
	omap3_evm_version = CONFIG_STATIC_BOARD_REV;
#else
	/* Fallback to the default above */
	omap3_evm_version = OMAP3EVM_BOARD_GEN_2;
#endif /* CONFIG_STATIC_BOARD_REV */
#endif /* CONFIG_CMD_NET */
}

#if defined(CONFIG_USB_MUSB_GADGET) || defined(CONFIG_USB_MUSB_HOST)
/* MUSB port on OMAP3EVM Rev >= E requires extvbus programming. */
u8 omap3_evm_need_extvbus(void)
{
	u8 retval = 0;

	if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
		retval = 1;

	return retval;
}
#endif /* CONFIG_USB_MUSB_{GADGET,HOST} */

/*
 * Routine: board_init
 * Description: Early hardware init.
 */
int board_init(void)
{
	gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
	/* board id for Linux */
	gd->bd->bi_arch_number = MACH_TYPE_OMAP3EVM;
	/* boot param addr */
	gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);

	return 0;
}

#if defined(CONFIG_SPL_OS_BOOT)
int spl_start_uboot(void)
{
	/* break into full u-boot on 'c' */
	if (serial_tstc() && serial_getc() == 'c')
		return 1;

	return 0;
}
#endif /* CONFIG_SPL_OS_BOOT */

#if defined(CONFIG_SPL_BUILD)
/*
 * Routine: get_board_mem_timings
 * Description: If we use SPL then there is no x-loader nor config header
 * so we have to setup the DDR timings ourself on the first bank.  This
 * provides the timing values back to the function that configures
 * the memory.
 */
void get_board_mem_timings(struct board_sdrc_timings *timings)
{
	int pop_mfr, pop_id;

	/*
	 * We need to identify what PoP memory is on the board so that
	 * we know what timings to use.  To map the ID values please see
	 * nand_ids.c
	 */
	identify_nand_chip(&pop_mfr, &pop_id);

	if (pop_mfr == NAND_MFR_HYNIX && pop_id == 0xbc) {
		/* 256MB DDR */
		timings->mcfg = HYNIX_V_MCFG_200(256 << 20);
		timings->ctrla = HYNIX_V_ACTIMA_200;
		timings->ctrlb = HYNIX_V_ACTIMB_200;
	} else {
		/* 128MB DDR */
		timings->mcfg = MICRON_V_MCFG_165(128 << 20);
		timings->ctrla = MICRON_V_ACTIMA_165;
		timings->ctrlb = MICRON_V_ACTIMB_165;
	}
	timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
	timings->mr = MICRON_V_MR_165;
}
#endif /* CONFIG_SPL_BUILD */

#if defined(CONFIG_USB_MUSB_OMAP2PLUS)
static struct musb_hdrc_config musb_config = {
	.multipoint     = 1,
	.dyn_fifo       = 1,
	.num_eps        = 16,
	.ram_bits       = 12,
};

static struct omap_musb_board_data musb_board_data = {
	.interface_type	= MUSB_INTERFACE_ULPI,
};

static struct musb_hdrc_platform_data musb_plat = {
#if defined(CONFIG_USB_MUSB_HOST)
	.mode           = MUSB_HOST,
#elif defined(CONFIG_USB_MUSB_GADGET)
	.mode		= MUSB_PERIPHERAL,
#else
#error "Please define either CONFIG_USB_MUSB_HOST or CONFIG_USB_MUSB_GADGET"
#endif /* CONFIG_USB_MUSB_{GADGET,HOST} */
	.config         = &musb_config,
	.power          = 100,
	.platform_ops	= &omap2430_ops,
	.board_data	= &musb_board_data,
};
#endif /* CONFIG_USB_MUSB_OMAP2PLUS */

/*
 * Routine: misc_init_r
 * Description: Init ethernet (done here so udelay works)
 */
int misc_init_r(void)
{
	twl4030_power_init();

#ifdef CONFIG_SYS_I2C_OMAP24XX
	i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
#endif

#if defined(CONFIG_CMD_NET)
	setup_net_chip();
#endif
	omap3_evm_get_revision();

#if defined(CONFIG_CMD_NET)
	reset_net_chip();
#endif
	omap_die_id_display();

#if defined(CONFIG_USB_MUSB_OMAP2PLUS)
	musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE);
#endif

#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)
	omap_die_id_usbethaddr();
#endif
	return 0;
}

/*
 * Routine: set_muxconf_regs
 * Description: Setting up the configuration Mux registers specific to the
 *		hardware. Many pins need to be moved from protect to primary
 *		mode.
 */
void set_muxconf_regs(void)
{
	MUX_EVM();
}

#if defined(CONFIG_CMD_NET)
/*
 * Routine: setup_net_chip
 * Description: Setting up the configuration GPMC registers specific to the
 *		Ethernet hardware.
 */
static void setup_net_chip(void)
{
	struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE;

	/* Configure GPMC registers */
	writel(NET_GPMC_CONFIG1, &gpmc_cfg->cs[5].config1);
	writel(NET_GPMC_CONFIG2, &gpmc_cfg->cs[5].config2);
	writel(NET_GPMC_CONFIG3, &gpmc_cfg->cs[5].config3);
	writel(NET_GPMC_CONFIG4, &gpmc_cfg->cs[5].config4);
	writel(NET_GPMC_CONFIG5, &gpmc_cfg->cs[5].config5);
	writel(NET_GPMC_CONFIG6, &gpmc_cfg->cs[5].config6);
	writel(NET_GPMC_CONFIG7, &gpmc_cfg->cs[5].config7);

	/* Enable off mode for NWE in PADCONF_GPMC_NWE register */
	writew(readw(&ctrl_base ->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe);
	/* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */
	writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe);
	/* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */
	writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00,
		&ctrl_base->gpmc_nadv_ale);
}

/**
 * Reset the ethernet chip.
 */
static void reset_net_chip(void)
{
	int ret;
	int rst_gpio;

	if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1) {
		rst_gpio = OMAP3EVM_GPIO_ETH_RST_GEN1;
	} else {
		rst_gpio = OMAP3EVM_GPIO_ETH_RST_GEN2;
	}

	ret = gpio_request(rst_gpio, "");
	if (ret < 0) {
		printf("Unable to get GPIO %d\n", rst_gpio);
		return ;
	}

	/* Configure as output */
	gpio_direction_output(rst_gpio, 0);

	/* Send a pulse on the GPIO pin */
	gpio_set_value(rst_gpio, 1);
	udelay(1);
	gpio_set_value(rst_gpio, 0);
	udelay(1);
	gpio_set_value(rst_gpio, 1);
}

int board_eth_init(bd_t *bis)
{
	int rc = 0;
#if defined(CONFIG_SMC911X)
#define STR_ENV_ETHADDR	"ethaddr"

	struct eth_device *dev;
	uchar eth_addr[6];

	rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);

	if (!eth_env_get_enetaddr(STR_ENV_ETHADDR, eth_addr)) {
		dev = eth_get_dev_by_index(0);
		if (dev) {
			eth_env_set_enetaddr(STR_ENV_ETHADDR, dev->enetaddr);
		} else {
			printf("omap3evm: Couldn't get eth device\n");
			rc = -1;
		}
	}
#endif /* CONFIG_SMC911X */
	return rc;
}
#endif /* CONFIG_CMD_NET */

#if defined(CONFIG_MMC)
int board_mmc_init(bd_t *bis)
{
	return omap_mmc_init(0, 0, 0, -1, -1);
}

void board_mmc_power_init(void)
{
	twl4030_power_mmc_init(0);
}
#endif /* CONFIG_MMC */

#if defined(CONFIG_USB_EHCI_HCD) && !defined(CONFIG_SPL_BUILD)
/* Call usb_stop() before starting the kernel */
void show_boot_progress(int val)
{
	if (val == BOOTSTAGE_ID_RUN_OS)
		usb_stop();
}

static struct omap_usbhs_board_data usbhs_bdata = {
	.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED
};

int ehci_hcd_init(int index, enum usb_init_type init,
		struct ehci_hccr **hccr, struct ehci_hcor **hcor)
{
	return omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor);
}

int ehci_hcd_stop(int index)
{
	return omap_ehci_hcd_stop();
}
#endif /* CONFIG_USB_EHCI_HCD */

#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET) && !defined(CONFIG_CMD_NET)
int board_eth_init(bd_t *bis)
{
	return usb_eth_initialize(bis);
}
#endif /* CONFIG_USB_ETHER */