diff options
author | York Sun <yorksun@freescale.com> | 2012-12-23 19:25:27 (GMT) |
---|---|---|
committer | Andy Fleming <afleming@freescale.com> | 2013-01-30 17:25:11 (GMT) |
commit | b5b06fb7b04a93ea48638d4d2ba1932051a28f64 (patch) | |
tree | 1724bf4db2f33fecfe09628de1faec621b251391 /board/freescale/b4860qds/b4860qds.c | |
parent | db9a807054ec82f4f6352677ea8b5d8176050a8a (diff) | |
download | u-boot-fsl-qoriq-b5b06fb7b04a93ea48638d4d2ba1932051a28f64.tar.xz |
powerpc/b4860qds: Added Support for B4860QDS
B4860QDS is a high-performance computing evaluation, development and
test platform supporting the B4860 QorIQ Power Architecture processor.
B4860QDS Overview
------------------
- DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,
ECC, 4 GB of memory in two ranks of 2 GB.
- DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 2 GB of memory. Single rank.
- SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point
16x16 switch VSC3316
- SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point
8x8 switch VSC3308
- USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode.
- B4860 UART port is available over USB-to-UART translator USB2SER or over
RS232 flat cable.
- A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper
connectors for Stand-alone mode and to the 1000Base-X over AMC MicroTCA
connector ports 0 and 2 for AMC mode.
- The B4860 configuration may be loaded from nine bits coded reset
configuration reset source. The RCW source is set by appropriate
DIP-switches:
- 16-bit NOR Flash / PROMJet
- QIXIS 8-bit NOR Flash Emulator
- 8-bit NAND Flash
- 24-bit SPI Flash
- Long address I2C EEPROM
- Available debug interfaces are:
- On-board eCWTAP controller with ETH and USB I/F
- JTAG/COP 16-pin header for any external TAP controller
- External JTAG source over AMC to support B2B configuration
- 70-pin Aurora debug connector
- QIXIS (FPGA) logic:
- 2 KB internal memory space including
- IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK,
DDRCLK1, 2 and RTCCLK.
- Two 8T49N222A SerDes ref clock devices support two SerDes port clocks
- total four refclk, including CPRI clock scheme
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Diffstat (limited to 'board/freescale/b4860qds/b4860qds.c')
-rw-r--r-- | board/freescale/b4860qds/b4860qds.c | 458 |
1 files changed, 458 insertions, 0 deletions
diff --git a/board/freescale/b4860qds/b4860qds.c b/board/freescale/b4860qds/b4860qds.c new file mode 100644 index 0000000..88bdc1f --- /dev/null +++ b/board/freescale/b4860qds/b4860qds.c @@ -0,0 +1,458 @@ +/* + * Copyright 2011-2012 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <command.h> +#include <i2c.h> +#include <netdev.h> +#include <linux/compiler.h> +#include <asm/mmu.h> +#include <asm/processor.h> +#include <asm/cache.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_law.h> +#include <asm/fsl_serdes.h> +#include <asm/fsl_portals.h> +#include <asm/fsl_liodn.h> +#include <fm_eth.h> + +#include "../common/qixis.h" +#include "../common/vsc3316_3308.h" +#include "b4860qds.h" +#include "b4860qds_qixis.h" +#include "b4860qds_crossbar_con.h" + +#define CLK_MUX_SEL_MASK 0x4 +#define ETH_PHY_CLK_OUT 0x4 + +DECLARE_GLOBAL_DATA_PTR; + +int checkboard(void) +{ + char buf[64]; + u8 sw; + struct cpu_type *cpu = gd->cpu; + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + unsigned int i; + static const char *const freq[] = {"100", "125", "156.25", "161.13", + "122.88", "122.88", "122.88"}; + int clock; + + printf("Board: %sQDS, ", cpu->name); + printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, ", + QIXIS_READ(id), QIXIS_READ(arch)); + + sw = QIXIS_READ(brdcfg[0]); + sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT; + + if (sw < 0x8) + printf("vBank: %d\n", sw); + else if (sw >= 0x8 && sw <= 0xE) + puts("NAND\n"); + else + printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH); + + printf("FPGA: v%d (%s), build %d", + (int)QIXIS_READ(scver), qixis_read_tag(buf), + (int)qixis_read_minor()); + /* the timestamp string contains "\n" at the end */ + printf(" on %s", qixis_read_time(buf)); + + /* Display the RCW, so that no one gets confused as to what RCW + * we're actually using for this boot. + */ + puts("Reset Configuration Word (RCW):"); + for (i = 0; i < ARRAY_SIZE(gur->rcwsr); i++) { + u32 rcw = in_be32(&gur->rcwsr[i]); + + if ((i % 4) == 0) + printf("\n %08x:", i * 4); + printf(" %08x", rcw); + } + puts("\n"); + + /* + * Display the actual SERDES reference clocks as configured by the + * dip switches on the board. Note that the SWx registers could + * technically be set to force the reference clocks to match the + * values that the SERDES expects (or vice versa). For now, however, + * we just display both values and hope the user notices when they + * don't match. + */ + puts("SERDES Reference Clocks: "); + sw = QIXIS_READ(brdcfg[2]); + clock = (sw >> 5) & 7; + printf("Bank1=%sMHz ", freq[clock]); + sw = QIXIS_READ(brdcfg[4]); + clock = (sw >> 6) & 3; + printf("Bank2=%sMHz\n", freq[clock]); + + return 0; +} + +int select_i2c_ch_pca(u8 ch) +{ + int ret; + + /* Selecting proper channel via PCA*/ + ret = i2c_write(I2C_MUX_PCA_ADDR, 0x0, 1, &ch, 1); + if (ret) { + printf("PCA: failed to select proper channel.\n"); + return ret; + } + + return 0; +} + +int configure_vsc3316_3308(void) +{ + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + unsigned int num_vsc16_con, num_vsc08_con; + u32 serdes1_prtcl, serdes2_prtcl; + int ret; + + serdes1_prtcl = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS1_PRTCL; + if (!serdes1_prtcl) { + printf("SERDES1 is not enabled\n"); + return 0; + } + serdes1_prtcl >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; + debug("Using SERDES1 Protocol: 0x%x:\n", serdes1_prtcl); + + serdes2_prtcl = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS2_PRTCL; + if (!serdes2_prtcl) { + printf("SERDES2 is not enabled\n"); + return 0; + } + serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; + debug("Using SERDES2 Protocol: 0x%x:\n", serdes2_prtcl); + + switch (serdes1_prtcl) { + case 0x2a: + case 0x2C: + case 0x2D: + case 0x2E: + /* + * Configuration: + * SERDES: 1 + * Lanes: A,B: SGMII + * Lanes: C,D,E,F,G,H: CPRI + */ + debug("Configuring crossbar to use onboard SGMII PHYs:" + "srds_prctl:%x\n", serdes1_prtcl); + num_vsc16_con = NUM_CON_VSC3316; + /* Configure VSC3316 crossbar switch */ + ret = select_i2c_ch_pca(I2C_CH_VSC3316); + if (!ret) { + ret = vsc3316_config(VSC3316_TX_ADDRESS, + vsc16_tx_sgmii_lane_ab, num_vsc16_con); + if (ret) + return ret; + ret = vsc3316_config(VSC3316_RX_ADDRESS, + vsc16_rx_sgmii_lane_ab, num_vsc16_con); + if (ret) + return ret; + } else { + return ret; + } + break; + +#ifdef CONFIG_PPC_B4420 + case 0x18: + /* + * Configuration: + * SERDES: 1 + * Lanes: A,B,C,D: SGMII + * Lanes: E,F,G,H: CPRI + */ + debug("Configuring crossbar to use onboard SGMII PHYs:" + "srds_prctl:%x\n", serdes1_prtcl); + num_vsc16_con = NUM_CON_VSC3316; + /* Configure VSC3316 crossbar switch */ + ret = select_i2c_ch_pca(I2C_CH_VSC3316); + if (!ret) { + ret = vsc3316_config(VSC3316_TX_ADDRESS, + vsc16_tx_sgmii_lane_cd, num_vsc16_con); + if (ret) + return ret; + ret = vsc3316_config(VSC3316_RX_ADDRESS, + vsc16_rx_sgmii_lane_cd, num_vsc16_con); + if (ret) + return ret; + } else { + return ret; + } + break; +#endif + + case 0x3E: + case 0x0D: + case 0x0E: + case 0x12: + num_vsc16_con = NUM_CON_VSC3316; + /* Configure VSC3316 crossbar switch */ + ret = select_i2c_ch_pca(I2C_CH_VSC3316); + if (!ret) { + ret = vsc3316_config(VSC3316_TX_ADDRESS, + vsc16_tx_sfp, num_vsc16_con); + if (ret) + return ret; + ret = vsc3316_config(VSC3316_RX_ADDRESS, + vsc16_rx_sfp, num_vsc16_con); + if (ret) + return ret; + } else { + return ret; + } + break; + default: + printf("WARNING:VSC crossbars programming not supported for:%x" + " SerDes1 Protocol.\n", serdes1_prtcl); + return -1; + } + + switch (serdes2_prtcl) { + case 0x9E: + case 0x9A: + case 0x98: + case 0xb2: + case 0x49: + case 0x4E: + case 0x8D: + case 0x7A: + num_vsc08_con = NUM_CON_VSC3308; + /* Configure VSC3308 crossbar switch */ + ret = select_i2c_ch_pca(I2C_CH_VSC3308); + if (!ret) { + ret = vsc3308_config(VSC3308_TX_ADDRESS, + vsc08_tx_amc, num_vsc08_con); + if (ret) + return ret; + ret = vsc3308_config(VSC3308_RX_ADDRESS, + vsc08_rx_amc, num_vsc08_con); + if (ret) + return ret; + } else { + return ret; + } + break; + default: + printf("WARNING:VSC crossbars programming not supported for: %x" + " SerDes2 Protocol.\n", serdes2_prtcl); + return -1; + } + + return 0; +} + +int board_early_init_r(void) +{ + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); + + /* + * Remap Boot flash + PROMJET region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* invalidate existing TLB entry for flash + promjet */ + disable_tlb(flash_esel); + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel, BOOKE_PAGESZ_256M, 1); + + set_liodns(); +#ifdef CONFIG_SYS_DPAA_QBMAN + setup_portals(); +#endif + + /* Configure VSC3316 and VSC3308 crossbar switches */ + if (configure_vsc3316_3308()) + printf("VSC:failed to configure VSC3316/3308.\n"); + else + printf("VSC:VSC3316/3308 successfully configured.\n"); + + select_i2c_ch_pca(I2C_CH_DEFAULT); + + return 0; +} + +unsigned long get_board_sys_clk(void) +{ + u8 sysclk_conf = QIXIS_READ(brdcfg[1]); + + switch ((sysclk_conf & 0x0C) >> 2) { + case QIXIS_CLK_100: + return 100000000; + case QIXIS_CLK_125: + return 125000000; + case QIXIS_CLK_133: + return 133333333; + } + return 66666666; +} + +unsigned long get_board_ddr_clk(void) +{ + u8 ddrclk_conf = QIXIS_READ(brdcfg[1]); + + switch (ddrclk_conf & 0x03) { + case QIXIS_CLK_100: + return 100000000; + case QIXIS_CLK_125: + return 125000000; + case QIXIS_CLK_133: + return 133333333; + } + return 66666666; +} + +static int serdes_refclock(u8 sw, u8 sdclk) +{ + unsigned int clock; + int ret = -1; + u8 brdcfg4; + + if (sdclk == 1) { + brdcfg4 = QIXIS_READ(brdcfg[4]); + if ((brdcfg4 & CLK_MUX_SEL_MASK) == ETH_PHY_CLK_OUT) + return SRDS_PLLCR0_RFCK_SEL_125; + else + clock = (sw >> 5) & 7; + } else + clock = (sw >> 6) & 3; + + switch (clock) { + case 0: + ret = SRDS_PLLCR0_RFCK_SEL_100; + break; + case 1: + ret = SRDS_PLLCR0_RFCK_SEL_125; + break; + case 2: + ret = SRDS_PLLCR0_RFCK_SEL_156_25; + break; + case 3: + ret = SRDS_PLLCR0_RFCK_SEL_161_13; + break; + case 4: + case 5: + case 6: + ret = SRDS_PLLCR0_RFCK_SEL_122_88; + break; + default: + ret = -1; + break; + } + + return ret; +} + +static const char *serdes_clock_to_string(u32 clock) +{ + switch (clock) { + case SRDS_PLLCR0_RFCK_SEL_100: + return "100"; + case SRDS_PLLCR0_RFCK_SEL_125: + return "125"; + case SRDS_PLLCR0_RFCK_SEL_156_25: + return "156.25"; + case SRDS_PLLCR0_RFCK_SEL_161_13: + return "161.13"; + default: + return "122.88"; + } +} + +#define NUM_SRDS_BANKS 2 + +int misc_init_r(void) +{ + u8 sw; + serdes_corenet_t *srds_regs = + (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR; + u32 actual[NUM_SRDS_BANKS]; + unsigned int i; + int clock; + + sw = QIXIS_READ(brdcfg[2]); + clock = serdes_refclock(sw, 1); + if (clock >= 0) + actual[0] = clock; + else + printf("Warning: SDREFCLK1 switch setting is unsupported\n"); + + sw = QIXIS_READ(brdcfg[4]); + clock = serdes_refclock(sw, 2); + if (clock >= 0) + actual[1] = clock; + else + printf("Warning: SDREFCLK2 switch setting unsupported\n"); + + for (i = 0; i < NUM_SRDS_BANKS; i++) { + u32 pllcr0 = srds_regs->bank[i].pllcr0; + u32 expected = pllcr0 & SRDS_PLLCR0_RFCK_SEL_MASK; + if (expected != actual[i]) { + printf("Warning: SERDES bank %u expects reference clock" + " %sMHz, but actual is %sMHz\n", i + 1, + serdes_clock_to_string(expected), + serdes_clock_to_string(actual[i])); + } + } + + return 0; +} + +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + +#ifdef CONFIG_PCI + pci_of_setup(blob, bd); +#endif + + fdt_fixup_liodn(blob); + +#ifdef CONFIG_HAS_FSL_DR_USB + fdt_fixup_dr_usb(blob, bd); +#endif + +#ifdef CONFIG_SYS_DPAA_FMAN + fdt_fixup_fman_ethernet(blob); + fdt_fixup_board_enet(blob); +#endif +} |