powerpc/p3060qds: Add board related support for P3060QDS platform

The P3060QDS is a Freescale reference board for the six-core P3060 SOC.

P3060QDS Board Overview:
 Memory subsystem:
  - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
  - 128M Bytes NOR flash single-chip memory
  - 16M Bytes SPI flash
  - 8K Bytes AT24C64 I2C EEPROM for RCW
 Ethernet:
  - Eight Ethernet controllers (4x1G + 4x1G/2.5G)
  - Three VSC8641 PHYs on board (2xRGMII + 1xMII)
  - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3
 PCIe: Two PCI Express 2.0 controllers/ports
 USB:  Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board
 I2C:  Four I2C controllers
 UART: Supports two dUARTs up to 115200 bps for console
 RapidIO:  Two RapidIO, sRIO1 and sRIO2

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

11 files changed, 1711 insertions, 8 deletions

diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile
index 353d3c6..9077aaf 100644
--- a/board/freescale/common/Makefile
+++ b/board/freescale/common/Makefile
@@ -34,6 +34,7 @@ COBJS-$(CONFIG_FSL_VIA)		+= cds_via.o
 COBJS-$(CONFIG_FMAN_ENET)	+= fman.o
 COBJS-$(CONFIG_FSL_PIXIS)	+= pixis.o
 COBJS-$(CONFIG_FSL_NGPIXIS)	+= ngpixis.o
+COBJS-$(CONFIG_FSL_QIXIS)	+= qixis.o
 COBJS-$(CONFIG_PQ_MDS_PIB)	+= pq-mds-pib.o
 COBJS-$(CONFIG_ID_EEPROM)	+= sys_eeprom.o
 COBJS-$(CONFIG_FSL_SGMII_RISER)	+= sgmii_riser.o
@@ -50,12 +51,14 @@ COBJS-$(CONFIG_MPC8572DS)	+= ics307_clk.o
 COBJS-$(CONFIG_P1022DS)		+= ics307_clk.o
 COBJS-$(CONFIG_P2020DS)		+= ics307_clk.o
 COBJS-$(CONFIG_P3041DS)		+= ics307_clk.o
+COBJS-$(CONFIG_P3060QDS)       	+= ics307_clk.o
 COBJS-$(CONFIG_P4080DS)		+= ics307_clk.o
 COBJS-$(CONFIG_P5020DS)		+= ics307_clk.o
 
 # deal with common files for P-series corenet based devices
 SUBLIB-$(CONFIG_P2041RDB)	+= p_corenet/libp_corenet.o
 SUBLIB-$(CONFIG_P3041DS)	+= p_corenet/libp_corenet.o
+SUBLIB-$(CONFIG_P3060QDS)	+= p_corenet/libp_corenet.o
 SUBLIB-$(CONFIG_P4080DS)	+= p_corenet/libp_corenet.o
 SUBLIB-$(CONFIG_P5020DS)	+= p_corenet/libp_corenet.o
 
diff --git a/board/freescale/common/ics307_clk.c b/board/freescale/common/ics307_clk.c
index 6acbc36..95a3cd7 100644
--- a/board/freescale/common/ics307_clk.c
+++ b/board/freescale/common/ics307_clk.c
@@ -1,5 +1,5 @@
 /*
- * Copyright 2010 Freescale Semiconductor, Inc.
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
  *
  * See file CREDITS for list of people who contributed to this
  * project.
@@ -25,10 +25,15 @@
 
 #include "ics307_clk.h"
 
-#ifdef CONFIG_FSL_NGPIXIS
+#if defined(CONFIG_FSL_NGPIXIS)
 #include "ngpixis.h"
+#define fpga_reg pixis
+#elif defined(CONFIG_FSL_QIXIS)
+#include "qixis.h"
+#define fpga_reg ((struct qixis *)QIXIS_BASE)
 #else
 #include "pixis.h"
+#define fpga_reg pixis
 #endif
 
 /* define for SYS CLK or CLK1Frequency */
@@ -143,15 +148,15 @@ static unsigned long ics307_clk_freq(u8 cw0, u8 cw1, u8 cw2)
 unsigned long get_board_sys_clk(void)
 {
 	return ics307_clk_freq(
-			in_8(&pixis->sclk[0]),
-			in_8(&pixis->sclk[1]),
-			in_8(&pixis->sclk[2]));
+			in_8(&fpga_reg->sclk[0]),
+			in_8(&fpga_reg->sclk[1]),
+			in_8(&fpga_reg->sclk[2]));
 }
 
 unsigned long get_board_ddr_clk(void)
 {
 	return ics307_clk_freq(
-			in_8(&pixis->dclk[0]),
-			in_8(&pixis->dclk[1]),
-			in_8(&pixis->dclk[2]));
+			in_8(&fpga_reg->dclk[0]),
+			in_8(&fpga_reg->dclk[1]),
+			in_8(&fpga_reg->dclk[2]));
 }
diff --git a/board/freescale/common/qixis.c b/board/freescale/common/qixis.c
new file mode 100644
index 0000000..6cd7e51
--- /dev/null
+++ b/board/freescale/common/qixis.c
@@ -0,0 +1,151 @@
+/*
+ * Copyright 2011 Freescale Semiconductor
+ * Author: Shengzhou Liu <Shengzhou.Liu@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This file provides support for the QIXIS of some Freescale reference boards.
+ *
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/io.h>
+#include "qixis.h"
+
+u8 qixis_read(unsigned int reg)
+{
+	void *p = (void *)QIXIS_BASE;
+
+	return in_8(p + reg);
+}
+
+void qixis_write(unsigned int reg, u8 value)
+{
+	void *p = (void *)QIXIS_BASE;
+
+	out_8(p + reg, value);
+}
+
+void qixis_reset(void)
+{
+	QIXIS_WRITE(rst_ctl, 0x83);
+}
+
+void qixis_bank_reset(void)
+{
+	QIXIS_WRITE(rcfg_ctl, 0x20);
+	QIXIS_WRITE(rcfg_ctl, 0x21);
+}
+
+/* Set the boot bank to the power-on default bank0 */
+void clear_altbank(void)
+{
+	u8 reg;
+
+	reg = QIXIS_READ(brdcfg[0]);
+	reg = reg & ~QIXIS_LBMAP_MASK;
+	QIXIS_WRITE(brdcfg[0], reg);
+}
+
+/* Set the boot bank to the alternate bank */
+void set_altbank(void)
+{
+	u8 reg;
+
+	reg = QIXIS_READ(brdcfg[0]);
+	reg = (reg & ~QIXIS_LBMAP_MASK) | QIXIS_LBMAP_ALTBANK;
+	QIXIS_WRITE(brdcfg[0], reg);
+}
+
+#ifdef DEBUG
+static void qixis_dump_regs(void)
+{
+	int i;
+
+	printf("id	= %02x\n", QIXIS_READ(id));
+	printf("arch	= %02x\n", QIXIS_READ(arch));
+	printf("scver	= %02x\n", QIXIS_READ(scver));
+	printf("model	= %02x\n", QIXIS_READ(model));
+	printf("rst_ctl	= %02x\n", QIXIS_READ(rst_ctl));
+	printf("aux	= %02x\n", QIXIS_READ(aux));
+	for (i = 0; i < 16; i++)
+		printf("brdcfg%02d = %02x\n", i, QIXIS_READ(brdcfg[i]));
+	for (i = 0; i < 16; i++)
+		printf("dutcfg%02d = %02x\n", i, QIXIS_READ(dutcfg[i]));
+	printf("sclk	= %02x%02x%02x\n", QIXIS_READ(sclk[0]),
+		QIXIS_READ(sclk[1]), QIXIS_READ(sclk[2]));
+	printf("dclk	= %02x%02x%02x\n", QIXIS_READ(dclk[0]),
+		QIXIS_READ(dclk[1]), QIXIS_READ(dclk[2]));
+	printf("aux     = %02x\n", QIXIS_READ(aux));
+	printf("watch	= %02x\n", QIXIS_READ(watch));
+	printf("ctl_sys	= %02x\n", QIXIS_READ(ctl_sys));
+	printf("rcw_ctl = %02x\n", QIXIS_READ(rcw_ctl));
+	printf("present = %02x\n", QIXIS_READ(present));
+	printf("clk_spd = %02x\n", QIXIS_READ(clk_spd));
+	printf("stat_dut = %02x\n", QIXIS_READ(stat_dut));
+	printf("stat_sys = %02x\n", QIXIS_READ(stat_sys));
+	printf("stat_alrm = %02x\n", QIXIS_READ(stat_alrm));
+	printf("ctl_sys2 = %02x\n", QIXIS_READ(ctl_sys2));
+}
+#endif
+
+int qixis_reset_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+	int i;
+
+	if (argc <= 1) {
+		clear_altbank();
+		qixis_reset();
+	} else if (strcmp(argv[1], "altbank") == 0) {
+		set_altbank();
+		qixis_bank_reset();
+	} else if (strcmp(argv[1], "watchdog") == 0) {
+		static char *period[9] = {"2s", "4s", "8s", "16s", "32s",
+					  "1min", "2min", "4min", "8min"};
+		u8 rcfg = QIXIS_READ(rcfg_ctl);
+
+		if (argv[2] == NULL) {
+			printf("qixis watchdog <watchdog_period>\n");
+			return 0;
+		}
+		for (i = 0; i < ARRAY_SIZE(period); i++) {
+			if (strcmp(argv[2], period[i]) == 0) {
+				/* disable watchdog */
+				QIXIS_WRITE(rcfg_ctl, rcfg & ~0x08);
+				QIXIS_WRITE(watch, ((i<<2) - 1));
+				QIXIS_WRITE(rcfg_ctl, rcfg);
+				return 0;
+			}
+		}
+	}
+
+#ifdef DEBUG
+	else if (strcmp(argv[1], "dump") == 0) {
+		qixis_dump_regs();
+		return 0;
+	}
+#endif
+
+	else {
+		printf("Invalid option: %s\n", argv[1]);
+		return 1;
+	}
+
+	return 0;
+}
+
+U_BOOT_CMD(
+	qixis_reset, CONFIG_SYS_MAXARGS, 1, qixis_reset_cmd,
+	"Reset the board using the FPGA sequencer",
+	"- hard reset to default bank\n"
+	"qixis_reset altbank - reset to alternate bank\n"
+	"qixis watchdog <watchdog_period> - set the watchdog period\n"
+	"	period: 1s 2s 4s 8s 16s 32s 1min 2min 4min 8min\n"
+#ifdef DEBUG
+	"qixis_reset dump - display the QIXIS registers\n"
+#endif
+	);
diff --git a/board/freescale/common/qixis.h b/board/freescale/common/qixis.h
new file mode 100644
index 0000000..7a0268a
--- /dev/null
+++ b/board/freescale/common/qixis.h
@@ -0,0 +1,101 @@
+/*
+ * Copyright 2011 Freescale Semiconductor
+ * Author: Shengzhou Liu <Shengzhou.Liu@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This file provides support for the QIXIS of some Freescale reference boards.
+ */
+
+#ifndef __QIXIS_H_
+#define __QIXIS_H_
+
+struct qixis {
+	u8 id;      /* ID value uniquely identifying each QDS board type */
+	u8 arch;    /* Board version information */
+	u8 scver;   /* QIXIS Version Register */
+	u8 model;   /* Information of software programming model version */
+	u8 tagdata;
+	u8 ctl_sys;
+	u8 aux;         /* Auxiliary Register,0x06 */
+	u8 clk_spd;
+	u8 stat_dut;
+	u8 stat_sys;
+	u8 stat_alrm;
+	u8 present;
+	u8 ctl_sys2;
+	u8 rcw_ctl;
+	u8 ctl_led;
+	u8 i2cblk;
+	u8 rcfg_ctl;    /* Reconfig Control Register,0x10 */
+	u8 rcfg_st;
+	u8 dcm_ad;
+	u8 dcm_da;
+	u8 dcmd;
+	u8 dmsg;
+	u8 gdc;
+	u8 gdd;         /* DCM Debug Data Register,0x17 */
+	u8 dmack;
+	u8 res1[6];
+	u8 watch;       /* Watchdog Register,0x1F */
+	u8 pwr_ctl[2];  /* Power Control Register,0x20 */
+	u8 res2[2];
+	u8 pwr_stat[4]; /* Power Status Register,0x24 */
+	u8 res3[8];
+	u8 clk_spd2[2];  /* SYSCLK clock Speed Register,0x30 */
+	u8 res4[2];
+	u8 sclk[3];  /* Clock Configuration Registers,0x34 */
+	u8 res5;
+	u8 dclk[3];
+	u8 res6;
+	u8 clk_dspd[3];
+	u8 res7;
+	u8 rst_ctl;     /* Reset Control Register,0x40 */
+	u8 rst_stat;    /* Reset Status Register */
+	u8 rst_rsn;     /* Reset Reason Register */
+	u8 rst_frc[2];  /* Reset Force Registers,0x43 */
+	u8 res8[11];
+	u8 brdcfg[16];  /* Board Configuration Register,0x50 */
+	u8 dutcfg[16];
+	u8 rcw_ad[2];   /* RCW SRAM Address Registers,0x70 */
+	u8 rcw_data;
+	u8 res9[5];
+	u8 post_ctl;
+	u8 post_stat;
+	u8 post_dat[2];
+	u8 pi_d[4];
+	u8 gpio_io[4];
+	u8 gpio_dir[4];
+	u8 res10[20];
+	u8 rjtag_ctl;
+	u8 rjtag_dat;
+	u8 res11[2];
+	u8 trig_src[4];
+	u8 trig_dst[4];
+	u8 trig_stat;
+	u8 res12[3];
+	u8 trig_ctr[4];
+	u8 res13[48];
+	u8 aux2[4];	/* Auxiliary Registers,0xE0 */
+	u8 res14[10];
+	u8 aux_ad;
+	u8 aux_da;
+	u8 res15[16];
+};
+
+#define QIXIS_BASE		0xffdf0000
+#define QIXIS_LBMAP_SWITCH	7
+#define QIXIS_LBMAP_MASK	0x0f
+#define QIXIS_LBMAP_SHIFT	0
+#define QIXIS_LBMAP_ALTBANK	0x04
+
+u8 qixis_read(unsigned int reg);
+void qixis_write(unsigned int reg, u8 value);
+
+#define QIXIS_READ(reg) qixis_read(offsetof(struct qixis, reg))
+#define QIXIS_WRITE(reg, value) qixis_write(offsetof(struct qixis, reg), value)
+
+#endif
diff --git a/board/freescale/p3060qds/Makefile b/board/freescale/p3060qds/Makefile
new file mode 100644
index 0000000..ae136f4
--- /dev/null
+++ b/board/freescale/p3060qds/Makefile
@@ -0,0 +1,54 @@
+#
+# Copyright 2011 Freescale Semiconductor, Inc.
+# (C) Copyright 2001-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS-y += $(BOARD).o
+COBJS-y += ddr.o
+COBJS-y += eth.o
+COBJS-y += fixed_ddr.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+clean:
+	rm -f $(OBJS) $(SOBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/p3060qds/ddr.c b/board/freescale/p3060qds/ddr.c
new file mode 100644
index 0000000..9affbf0
--- /dev/null
+++ b/board/freescale/p3060qds/ddr.c
@@ -0,0 +1,248 @@
+/*
+ * Copyright 2009-2011 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <hwconfig.h>
+#include <asm/mmu.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+#include <asm/fsl_law.h>
+
+#include "p3060qds.h"
+
+/*
+ * Fixed sdram init -- doesn't use serial presence detect.
+ */
+
+phys_size_t fixed_sdram(void)
+{
+	int i;
+	char buf[32];
+	fsl_ddr_cfg_regs_t ddr_cfg_regs;
+	phys_size_t ddr_size;
+	unsigned int lawbar1_target_id;
+	ulong ddr_freq, ddr_freq_mhz;
+
+	ddr_freq = get_ddr_freq(0);
+	ddr_freq_mhz = ddr_freq / 1000000;
+
+	printf("Configuring DDR for %s MT/s data rate\n",
+				strmhz(buf, ddr_freq));
+
+	for (i = 0; fixed_ddr_parm_0[i].max_freq > 0; i++) {
+		if ((ddr_freq_mhz > fixed_ddr_parm_0[i].min_freq) &&
+		   (ddr_freq_mhz <= fixed_ddr_parm_0[i].max_freq)) {
+			memcpy(&ddr_cfg_regs,
+				fixed_ddr_parm_0[i].ddr_settings,
+				sizeof(ddr_cfg_regs));
+			break;
+		}
+	}
+
+	if (fixed_ddr_parm_0[i].max_freq == 0)
+		panic("Unsupported DDR data rate %s MT/s data rate\n",
+			strmhz(buf, ddr_freq));
+
+	ddr_size = (phys_size_t) CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
+	ddr_cfg_regs.ddr_cdr1 = DDR_CDR1_DHC_EN;
+	fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0);
+
+	/*
+	 * setup laws for DDR. If not interleaving, presuming half memory on
+	 * DDR1 and the other half on DDR2
+	 */
+	if (fixed_ddr_parm_0[i].ddr_settings->cs[0].config & 0x20000000) {
+		if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE,
+				 ddr_size,
+				 LAW_TRGT_IF_DDR_INTRLV) < 0) {
+			printf("ERROR setting Local Access Windows for DDR\n");
+			return 0;
+		}
+	} else {
+		lawbar1_target_id = LAW_TRGT_IF_DDR_1;
+		if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE,
+				 ddr_size,
+				 lawbar1_target_id) < 0) {
+			printf("ERROR setting Local Access Windows for DDR\n");
+			return 0;
+		}
+	}
+	return ddr_size;
+}
+
+struct board_specific_params {
+	u32 n_ranks;
+	u32 datarate_mhz_high;
+	u32 clk_adjust;
+	u32 wrlvl_start;
+	u32 cpo;
+	u32 write_data_delay;
+	u32 force_2T;
+};
+
+/*
+ * This table contains all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+static const struct board_specific_params udimm[] = {
+	/*
+	 * memory controller 0
+	 *   num|  hi|  clk| wrlvl | cpo  |wrdata|2T
+	 * ranks| mhz|adjst| start |      |delay |
+	 */
+	{4,   850,    4,     6,   0xff,    2,  0},
+	{4,   950,    5,     7,   0xff,    2,  0},
+	{4,  1050,    5,     8,   0xff,    2,  0},
+	{4,  1250,    5,    10,   0xff,    2,  0},
+	{4,  1350,    5,    11,   0xff,    2,  0},
+	{4,  1666,    5,    12,   0xff,    2,  0},
+	{2,   850,    5,     6,   0xff,    2,  0},
+	{2,   950,    5,     7,   0xff,    2,  0},
+	{2,  1250,    4,     6,   0xff,    2,  0},
+	{2,  1350,    5,     7,   0xff,    2,  0},
+	{2,  1666,    5,     8,   0xff,    2,  0},
+	{1,   850,    4,     5,   0xff,    2,  0},
+	{1,   950,    4,     7,   0xff,    2,  0},
+	{1,  1666,    4,     8,   0xff,    2,  0},
+	{}
+};
+
+static const struct board_specific_params rdimm[] = {
+	/*
+	 * memory controller 0
+	 *   num|  hi|  clk| wrlvl | cpo  |wrdata|2T
+	 * ranks| mhz|adjst| start |      |delay |
+	 */
+	{4,   850,    4,     6,   0xff,    2,  0},
+	{4,   950,    5,     7,   0xff,    2,  0},
+	{4,  1050,    5,     8,   0xff,    2,  0},
+	{4,  1250,    5,    10,   0xff,    2,  0},
+	{4,  1350,    5,    11,   0xff,    2,  0},
+	{4,  1666,    5,    12,   0xff,    2,  0},
+	{2,   850,    4,     6,   0xff,    2,  0},
+	{2,  1050,    4,     7,   0xff,    2,  0},
+	{2,  1666,    4,     8,   0xff,    2,  0},
+	{1,   850,    4,     5,   0xff,    2,  0},
+	{1,   950,    4,     7,   0xff,    2,  0},
+	{1,  1666,    4,     8,   0xff,    2,  0},
+	{}
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+				dimm_params_t *pdimm,
+				unsigned int ctrl_num)
+{
+	const struct board_specific_params *pbsp, *pbsp_highest = NULL;
+	ulong ddr_freq;
+
+	if (ctrl_num) {
+		printf("Wrong parameter for controller number %d", ctrl_num);
+		return;
+	}
+	if (!pdimm->n_ranks)
+		return;
+
+	if (popts->registered_dimm_en)
+		pbsp = rdimm;
+	else
+		pbsp = udimm;
+
+	/* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+	 * freqency and n_banks specified in board_specific_parameters table.
+	 */
+	ddr_freq = get_ddr_freq(0) / 1000000;
+	while (pbsp->datarate_mhz_high) {
+		if (pbsp->n_ranks == pdimm->n_ranks) {
+			if (ddr_freq <= pbsp->datarate_mhz_high) {
+				popts->cpo_override = pbsp->cpo;
+				popts->write_data_delay =
+					pbsp->write_data_delay;
+				popts->clk_adjust = pbsp->clk_adjust;
+				popts->wrlvl_start = pbsp->wrlvl_start;
+				popts->twoT_en = pbsp->force_2T;
+				goto found;
+			}
+			pbsp_highest = pbsp;
+		}
+		pbsp++;
+	}
+
+	if (pbsp_highest) {
+		printf("Error: board specific timing not found "
+			"for data rate %lu MT/s!\n"
+			"Trying to use the highest speed (%u) parameters\n",
+			ddr_freq, pbsp_highest->datarate_mhz_high);
+		popts->cpo_override = pbsp_highest->cpo;
+		popts->write_data_delay = pbsp_highest->write_data_delay;
+		popts->clk_adjust = pbsp_highest->clk_adjust;
+		popts->wrlvl_start = pbsp_highest->wrlvl_start;
+		popts->twoT_en = pbsp_highest->force_2T;
+	} else {
+		panic("DIMM is not supported by this board");
+	}
+
+
+found:
+
+	/*
+	 * The datasheet of HMT125U7BFR8C-H9 blocks CL=7 as reservered.
+	 * However SPD still claims CL=7 is supported. Extensive tests
+	 * confirmed this board cannot work stably with CL=7 with this
+	 * particular DIMM.
+	 */
+	if (ddr_freq >= 800 && ddr_freq < 1066 && \
+		!strncmp(pdimm[0].mpart, "HMT125U7BFR8C-H9", 16)) {
+		popts->cas_latency_override = 1;
+		popts->cas_latency_override_value = 8;
+		debug("Override CL to 8\n");
+	}
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+	/*
+	 * Write leveling override
+	 */
+	popts->wrlvl_override = 1;
+	popts->wrlvl_sample = 0xf;
+
+	/*
+	 * Rtt and Rtt_WR override
+	 */
+	popts->rtt_override = 0;
+
+	/* Enable ZQ calibration */
+	popts->zq_en = 1;
+
+	/* DHC_EN =1, ODT = 60 Ohm */
+	popts->ddr_cdr1 = DDR_CDR1_DHC_EN;
+}
+
+phys_size_t initdram(int board_type)
+{
+	phys_size_t dram_size;
+
+	puts("Initializing....");
+
+	if (fsl_use_spd()) {
+		puts("using SPD\n");
+		dram_size = fsl_ddr_sdram();
+	} else {
+		puts("using fixed parameters\n");
+		dram_size = fixed_sdram();
+	}
+
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
+
+	debug("    DDR: ");
+	return dram_size;
+}
diff --git a/board/freescale/p3060qds/eth.c b/board/freescale/p3060qds/eth.c
new file mode 100644
index 0000000..3f812db
--- /dev/null
+++ b/board/freescale/p3060qds/eth.c
@@ -0,0 +1,482 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <malloc.h>
+#include <fm_eth.h>
+#include <fsl_mdio.h>
+#include <miiphy.h>
+#include <phy.h>
+#include <asm/fsl_dtsec.h>
+
+#include "../common/qixis.h"
+#include "../common/fman.h"
+
+#include "p3060qds_qixis.h"
+
+#define EMI_NONE       0xffffffff
+#define EMI1_RGMII1    0
+#define EMI1_SLOT1     1
+#define EMI1_SLOT2     2
+#define EMI1_SLOT3     3
+#define EMI1_RGMII2    4
+
+static int mdio_mux[NUM_FM_PORTS];
+
+static char *mdio_names[5] = {
+	"P3060QDS_MDIO0",
+	"P3060QDS_MDIO1",
+	"P3060QDS_MDIO2",
+	"P3060QDS_MDIO3",
+	"P3060QDS_MDIO4",
+};
+
+/*
+ * Mapping of all 18 SERDES lanes to board slots.
+ * A value of '0' here means that the mapping must be determined
+ * dynamically, Lane 8/9/16/17 map to Slot1 or Aurora debug
+ */
+static u8 lane_to_slot[] = {
+	4, 4, 4, 4, 3, 3, 3, 3, 0, 0, 2, 2, 2, 2, 1, 1, 0, 0
+};
+
+static char *p3060qds_mdio_name_for_muxval(u32 muxval)
+{
+	return mdio_names[muxval];
+}
+
+struct mii_dev *mii_dev_for_muxval(u32 muxval)
+{
+	struct mii_dev *bus;
+	char *name = p3060qds_mdio_name_for_muxval(muxval);
+
+	if (!name) {
+		printf("No bus for muxval %x\n", muxval);
+		return NULL;
+	}
+
+	bus = miiphy_get_dev_by_name(name);
+
+	if (!bus) {
+		printf("No bus by name %s\n", name);
+		return NULL;
+	}
+
+	return bus;
+}
+
+struct p3060qds_mdio {
+	u32 muxval;
+	struct mii_dev *realbus;
+};
+
+static void p3060qds_mux_mdio(u32 muxval)
+{
+	u8 brdcfg4;
+
+	brdcfg4 = QIXIS_READ(brdcfg[4]);
+	brdcfg4 &= ~BRDCFG4_EMISEL_MASK;
+	brdcfg4 |= (muxval << 4);
+	QIXIS_WRITE(brdcfg[4], brdcfg4);
+}
+
+static int p3060qds_mdio_read(struct mii_dev *bus, int addr, int devad,
+				int regnum)
+{
+	struct p3060qds_mdio *priv = bus->priv;
+
+	p3060qds_mux_mdio(priv->muxval);
+
+	return priv->realbus->read(priv->realbus, addr, devad, regnum);
+}
+
+static int p3060qds_mdio_write(struct mii_dev *bus, int addr, int devad,
+				int regnum, u16 value)
+{
+	struct p3060qds_mdio *priv = bus->priv;
+
+	p3060qds_mux_mdio(priv->muxval);
+
+	return priv->realbus->write(priv->realbus, addr, devad, regnum, value);
+}
+
+static int p3060qds_mdio_reset(struct mii_dev *bus)
+{
+	struct p3060qds_mdio *priv = bus->priv;
+
+	return priv->realbus->reset(priv->realbus);
+}
+
+static int p3060qds_mdio_init(char *realbusname, u32 muxval)
+{
+	struct p3060qds_mdio *pmdio;
+	struct mii_dev *bus = mdio_alloc();
+
+	if (!bus) {
+		printf("Failed to allocate P3060QDS MDIO bus\n");
+		return -1;
+	}
+
+	pmdio = malloc(sizeof(*pmdio));
+	if (!pmdio) {
+		printf("Failed to allocate P3060QDS private data\n");
+		free(bus);
+		return -1;
+	}
+
+	bus->read = p3060qds_mdio_read;
+	bus->write = p3060qds_mdio_write;
+	bus->reset = p3060qds_mdio_reset;
+	sprintf(bus->name, p3060qds_mdio_name_for_muxval(muxval));
+
+	pmdio->realbus = miiphy_get_dev_by_name(realbusname);
+
+	if (!pmdio->realbus) {
+		printf("No bus with name %s\n", realbusname);
+		free(bus);
+		free(pmdio);
+		return -1;
+	}
+
+	pmdio->muxval = muxval;
+	bus->priv = pmdio;
+
+	return mdio_register(bus);
+}
+
+void board_ft_fman_fixup_port(void *blob, char * prop, phys_addr_t pa,
+				enum fm_port port, int offset)
+{
+	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	int srds_prtcl = (in_be32(&gur->rcwsr[4]) &
+			  FSL_CORENET_RCWSR4_SRDS_PRTCL) >> 26;
+
+	if (mdio_mux[port] == EMI1_RGMII1)
+		fdt_set_phy_handle(blob, prop, pa, "phy_rgmii1");
+
+	if (mdio_mux[port] == EMI1_RGMII2)
+		fdt_set_phy_handle(blob, prop, pa, "phy_rgmii2");
+
+	if ((mdio_mux[port] == EMI1_SLOT1) && ((srds_prtcl == 0x3)
+		|| (srds_prtcl == 0x6))) {
+		switch (port) {
+		case FM2_DTSEC4:
+			fdt_set_phy_handle(blob, prop, pa, "phy2_slot1");
+			break;
+		case FM1_DTSEC4:
+			fdt_set_phy_handle(blob, prop, pa, "phy3_slot1");
+			break;
+		default:
+			break;
+		}
+	}
+
+	if (mdio_mux[port] == EMI1_SLOT3) {
+		switch (port) {
+		case FM2_DTSEC3:
+			fdt_set_phy_handle(blob, prop, pa, "phy0_slot3");
+			break;
+		case FM1_DTSEC3:
+			fdt_set_phy_handle(blob, prop, pa, "phy1_slot3");
+			break;
+		default:
+			break;
+		}
+	}
+}
+
+void fdt_fixup_board_enet(void *fdt)
+{
+	int i, lane, idx;
+
+	for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
+		idx = i - FM1_DTSEC1;
+		switch (fm_info_get_enet_if(i)) {
+		case PHY_INTERFACE_MODE_SGMII:
+			lane = serdes_get_first_lane(SGMII_FM1_DTSEC1 + idx);
+			if (lane < 0)
+				break;
+
+			switch (mdio_mux[i]) {
+			case EMI1_SLOT1:
+				if (lane >= 14) {
+					fdt_status_okay_by_alias(fdt,
+						"emi1_slot1");
+					fdt_status_disabled_by_alias(fdt,
+						"emi1_slot1_bk1");
+				} else {
+					fdt_status_disabled_by_alias(fdt,
+						"emi1_slot1");
+					fdt_status_okay_by_alias(fdt,
+						"emi1_slot1_bk1");
+				}
+				break;
+			case EMI1_SLOT2:
+				fdt_status_okay_by_alias(fdt, "emi1_slot2");
+				break;
+			case EMI1_SLOT3:
+				fdt_status_okay_by_alias(fdt, "emi1_slot3");
+				break;
+			}
+		break;
+		case PHY_INTERFACE_MODE_RGMII:
+			if (i == FM1_DTSEC1)
+				fdt_status_okay_by_alias(fdt, "emi1_rgmii1");
+
+			if (i == FM1_DTSEC2)
+				fdt_status_okay_by_alias(fdt, "emi1_rgmii2");
+			break;
+		default:
+			break;
+		}
+	}
+#if (CONFIG_SYS_NUM_FMAN == 2)
+	for (i = FM2_DTSEC1; i < FM2_DTSEC1 + CONFIG_SYS_NUM_FM2_DTSEC; i++) {
+		idx = i - FM2_DTSEC1;
+		switch (fm_info_get_enet_if(i)) {
+		case PHY_INTERFACE_MODE_SGMII:
+			lane = serdes_get_first_lane(SGMII_FM2_DTSEC1 + idx);
+			if (lane >= 0) {
+				switch (mdio_mux[i]) {
+				case EMI1_SLOT1:
+					if (lane >= 14)
+						fdt_status_okay_by_alias(fdt,
+							"emi1_slot1");
+					else
+						fdt_status_okay_by_alias(fdt,
+							"emi1_slot1_bk1");
+					break;
+				case EMI1_SLOT2:
+					fdt_status_okay_by_alias(fdt,
+						"emi1_slot2");
+					break;
+				case EMI1_SLOT3:
+					fdt_status_okay_by_alias(fdt,
+						"emi1_slot3");
+					break;
+				}
+			}
+			break;
+		default:
+			break;
+		}
+	}
+#endif
+}
+
+static void initialize_lane_to_slot(void)
+{
+	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	int sdprtl = (in_be32(&gur->rcwsr[4]) &
+				FSL_CORENET_RCWSR4_SRDS_PRTCL) >> 26;
+
+	switch (sdprtl) {
+	case 0x03:
+	case 0x06:
+		lane_to_slot[8] = 1;
+		lane_to_slot[9] = lane_to_slot[8];
+		lane_to_slot[16] = 5;
+		lane_to_slot[17] = lane_to_slot[16];
+		break;
+	case 0x16:
+	case 0x19:
+	case 0x1C:
+		lane_to_slot[8] = 5;
+		lane_to_slot[9] = lane_to_slot[8];
+		lane_to_slot[16] = 1;
+		lane_to_slot[17] = lane_to_slot[16];
+		break;
+	default:
+		puts("Invalid SerDes protocol for P3060QDS\n");
+		break;
+	}
+}
+
+int board_eth_init(bd_t *bis)
+{
+#ifdef CONFIG_FMAN_ENET
+	struct dtsec *tsec = (void *)CONFIG_SYS_FSL_FM1_DTSEC1_ADDR;
+	int i;
+	struct fsl_pq_mdio_info dtsec_mdio_info;
+	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	int srds_cfg = (in_be32(&gur->rcwsr[4]) &
+				FSL_CORENET_RCWSR4_SRDS_PRTCL) >> 26;
+
+	initialize_lane_to_slot();
+
+	/*
+	 * Set TBIPA on FM1@DTSEC1.  This is needed for configurations
+	 * where FM1@DTSEC1 isn't used directly, since it provides
+	 * MDIO for other ports.
+	 */
+	out_be32(&tsec->tbipa, CONFIG_SYS_TBIPA_VALUE);
+
+	/* Initialize the mdio_mux array so we can recognize empty elements */
+	for (i = 0; i < NUM_FM_PORTS; i++)
+		mdio_mux[i] = EMI_NONE;
+
+	dtsec_mdio_info.regs =
+		(struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR;
+	dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+	/* Register the 1G MDIO bus */
+	fsl_pq_mdio_init(bis, &dtsec_mdio_info);
+
+	/* Register the 5 muxing front-ends to the MDIO buses */
+	if (fm_info_get_enet_if(FM1_DTSEC1) == PHY_INTERFACE_MODE_RGMII)
+		p3060qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII1);
+
+	if (fm_info_get_enet_if(FM1_DTSEC2) == PHY_INTERFACE_MODE_RGMII)
+		p3060qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII2);
+	p3060qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT1);
+	p3060qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT2);
+	p3060qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT3);
+
+	if (fm_info_get_enet_if(FM1_DTSEC1) == PHY_INTERFACE_MODE_RGMII)
+		fm_info_set_phy_address(FM1_DTSEC1, 1); /* RGMII1 */
+	else if (fm_info_get_enet_if(FM1_DTSEC1) == PHY_INTERFACE_MODE_SGMII)
+		fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT2_PHY_ADDR);
+
+	if (fm_info_get_enet_if(FM1_DTSEC2) == PHY_INTERFACE_MODE_RGMII)
+		fm_info_set_phy_address(FM1_DTSEC2, 2); /* RGMII2 */
+	else if (fm_info_get_enet_if(FM1_DTSEC2) == PHY_INTERFACE_MODE_SGMII)
+		fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT4_PHY_ADDR);
+
+	fm_info_set_phy_address(FM2_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
+	fm_info_set_phy_address(FM2_DTSEC2, SGMII_CARD_PORT3_PHY_ADDR);
+
+	switch (srds_cfg) {
+	case 0x03:
+	case 0x06:
+		fm_info_set_phy_address(FM2_DTSEC3, SGMII_CARD_PORT3_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT4_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC4, SGMII_CARD_PORT1_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC4, SGMII_CARD_PORT2_PHY_ADDR);
+		break;
+	case 0x16:
+	case 0x19:
+	case 0x1C:
+		fm_info_set_phy_address(FM2_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT2_PHY_ADDR);
+		fm_info_set_phy_address(FM2_DTSEC4, SGMII_CARD_PORT3_PHY_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC4, SGMII_CARD_PORT4_PHY_ADDR);
+		break;
+	default:
+		puts("Invalid SerDes protocol for P3060QDS\n");
+		break;
+	}
+
+	for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
+		int idx = i - FM1_DTSEC1, lane, slot;
+		switch (fm_info_get_enet_if(i)) {
+		case PHY_INTERFACE_MODE_SGMII:
+			lane = serdes_get_first_lane(SGMII_FM1_DTSEC1 + idx);
+			if (lane < 0)
+				break;
+			slot = lane_to_slot[lane];
+			if (QIXIS_READ(present) & (1 << (slot - 1)))
+				fm_disable_port(i);
+			switch (slot) {
+			case 1:
+				mdio_mux[i] = EMI1_SLOT1;
+				fm_info_set_mdio(i,
+					mii_dev_for_muxval(mdio_mux[i]));
+				break;
+			case 2:
+				mdio_mux[i] = EMI1_SLOT2;
+				fm_info_set_mdio(i,
+					mii_dev_for_muxval(mdio_mux[i]));
+				break;
+			case 3:
+				mdio_mux[i] = EMI1_SLOT3;
+				fm_info_set_mdio(i,
+					mii_dev_for_muxval(mdio_mux[i]));
+				break;
+			};
+			break;
+		case PHY_INTERFACE_MODE_RGMII:
+			if (i == FM1_DTSEC1) {
+				mdio_mux[i] = EMI1_RGMII1;
+				fm_info_set_mdio(i,
+					mii_dev_for_muxval(mdio_mux[i]));
+			} else if (i == FM1_DTSEC2) {
+				mdio_mux[i] = EMI1_RGMII2;
+				fm_info_set_mdio(i,
+					mii_dev_for_muxval(mdio_mux[i]));
+			}
+			break;
+		default:
+			break;
+		}
+	}
+
+#if (CONFIG_SYS_NUM_FMAN == 2)
+	for (i = FM2_DTSEC1; i < FM2_DTSEC1 + CONFIG_SYS_NUM_FM2_DTSEC; i++) {
+		int idx = i - FM2_DTSEC1, lane, slot;
+		switch (fm_info_get_enet_if(i)) {
+		case PHY_INTERFACE_MODE_SGMII:
+			lane = serdes_get_first_lane(SGMII_FM2_DTSEC1 + idx);
+			if (lane < 0)
+				break;
+			slot = lane_to_slot[lane];
+			if (QIXIS_READ(present) & (1 << (slot - 1)))
+				fm_disable_port(i);
+			switch (slot) {
+			case 1:
+				mdio_mux[i] = EMI1_SLOT1;
+				fm_info_set_mdio(i,
+					mii_dev_for_muxval(mdio_mux[i]));
+				break;
+			case 2:
+				mdio_mux[i] = EMI1_SLOT2;
+				fm_info_set_mdio(i,
+					mii_dev_for_muxval(mdio_mux[i]));
+				break;
+			case 3:
+				mdio_mux[i] = EMI1_SLOT3;
+				fm_info_set_mdio(i,
+					mii_dev_for_muxval(mdio_mux[i]));
+				break;
+			};
+			break;
+		default:
+			break;
+		}
+	}
+#endif /* CONFIG_SYS_NUM_FMAN */
+
+	cpu_eth_init(bis);
+#endif /* CONFIG_FMAN_ENET */
+
+	return pci_eth_init(bis);
+}
diff --git a/board/freescale/p3060qds/fixed_ddr.c b/board/freescale/p3060qds/fixed_ddr.c
new file mode 100644
index 0000000..125988d
--- /dev/null
+++ b/board/freescale/p3060qds/fixed_ddr.c
@@ -0,0 +1,214 @@
+/*
+ * Copyright 2009-2011 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <asm/fsl_ddr_sdram.h>
+
+#define CONFIG_SYS_DDR_TIMING_3_1200	0x01030000
+#define CONFIG_SYS_DDR_TIMING_0_1200	0xCC550104
+#define CONFIG_SYS_DDR_TIMING_1_1200	0x868FAA45
+#define CONFIG_SYS_DDR_TIMING_2_1200	0x0FB8A912
+#define CONFIG_SYS_DDR_MODE_1_1200	0x00441A40
+#define CONFIG_SYS_DDR_MODE_2_1200	0x00100000
+#define CONFIG_SYS_DDR_INTERVAL_1200	0x12480100
+#define CONFIG_SYS_DDR_CLK_CTRL_1200	0x02800000
+
+#define CONFIG_SYS_DDR_TIMING_3_1000	0x00020000
+#define CONFIG_SYS_DDR_TIMING_0_1000	0xCC440104
+#define CONFIG_SYS_DDR_TIMING_1_1000	0x727DF944
+#define CONFIG_SYS_DDR_TIMING_2_1000	0x0FB088CF
+#define CONFIG_SYS_DDR_MODE_1_1000	0x00441830
+#define CONFIG_SYS_DDR_MODE_2_1000	0x00080000
+#define CONFIG_SYS_DDR_INTERVAL_1000	0x0F3C0100
+#define CONFIG_SYS_DDR_CLK_CTRL_1000	0x02800000
+
+#define CONFIG_SYS_DDR_TIMING_3_900	0x00020000
+#define CONFIG_SYS_DDR_TIMING_0_900	0xCC440104
+#define CONFIG_SYS_DDR_TIMING_1_900	0x616ba844
+#define CONFIG_SYS_DDR_TIMING_2_900	0x0fb088ce
+#define CONFIG_SYS_DDR_MODE_1_900	0x00441620
+#define CONFIG_SYS_DDR_MODE_2_900	0x00080000
+#define CONFIG_SYS_DDR_INTERVAL_900	0x0db60100
+#define CONFIG_SYS_DDR_CLK_CTRL_900	0x02800000
+
+#define CONFIG_SYS_DDR_TIMING_3_800	0x00020000
+#define CONFIG_SYS_DDR_TIMING_0_800	0xcc330104
+#define CONFIG_SYS_DDR_TIMING_1_800	0x6f6b4744
+#define CONFIG_SYS_DDR_TIMING_2_800	0x0fa888cc
+#define CONFIG_SYS_DDR_MODE_1_800	0x00441420
+#define CONFIG_SYS_DDR_MODE_2_800	0x00000000
+#define CONFIG_SYS_DDR_INTERVAL_800	0x0c300100
+#define CONFIG_SYS_DDR_CLK_CTRL_800	0x02800000
+
+#define CONFIG_SYS_DDR_CS0_BNDS		0x000000FF
+#define CONFIG_SYS_DDR_CS1_BNDS		0x00000000
+#define CONFIG_SYS_DDR_CS2_BNDS		0x000000FF
+#define CONFIG_SYS_DDR_CS3_BNDS		0x000000FF
+#define CONFIG_SYS_DDR2_CS0_BNDS	0x000000FF
+#define CONFIG_SYS_DDR2_CS1_BNDS	0x00000000
+#define CONFIG_SYS_DDR2_CS2_BNDS	0x000000FF
+#define CONFIG_SYS_DDR2_CS3_BNDS	0x000000FF
+#define CONFIG_SYS_DDR_CS0_CONFIG	0xA0044202
+#define CONFIG_SYS_DDR_CS0_CONFIG_2	0x00000000
+#define CONFIG_SYS_DDR_CS1_CONFIG	0x80004202
+#define CONFIG_SYS_DDR_CS2_CONFIG	0x00000000
+#define CONFIG_SYS_DDR_CS3_CONFIG	0x00000000
+#define CONFIG_SYS_DDR2_CS0_CONFIG	0x80044202
+#define CONFIG_SYS_DDR2_CS1_CONFIG	0x80004202
+#define CONFIG_SYS_DDR2_CS2_CONFIG	0x00000000
+#define CONFIG_SYS_DDR2_CS3_CONFIG	0x00000000
+#define CONFIG_SYS_DDR_INIT_ADDR	0x00000000
+#define CONFIG_SYS_DDR_INIT_EXT_ADDR	0x00000000
+#define CONFIG_SYS_DDR_CS1_CONFIG	0x80004202
+#define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
+#define CONFIG_SYS_DDR_TIMING_4		0x00000001
+#define CONFIG_SYS_DDR_TIMING_5		0x02401400
+#define CONFIG_SYS_DDR_MODE_CONTROL	0x00000000
+#define CONFIG_SYS_DDR_ZQ_CNTL		0x89080600
+#define CONFIG_SYS_DDR_WRLVL_CNTL	0x8675F607
+#define CONFIG_SYS_DDR_SDRAM_CFG	0xE7044000
+#define CONFIG_SYS_DDR_SDRAM_CFG2	0x24401031
+#define CONFIG_SYS_DDR_RCW_1		0x00000000
+#define CONFIG_SYS_DDR_RCW_2		0x00000000
+#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
+
+fsl_ddr_cfg_regs_t ddr_cfg_regs_800 = {
+	.cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS,
+	.cs[1].bnds = CONFIG_SYS_DDR_CS1_BNDS,
+	.cs[2].bnds = CONFIG_SYS_DDR_CS2_BNDS,
+	.cs[3].bnds = CONFIG_SYS_DDR_CS3_BNDS,
+	.cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG,
+	.cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2,
+	.cs[1].config = CONFIG_SYS_DDR_CS1_CONFIG,
+	.cs[2].config = CONFIG_SYS_DDR_CS2_CONFIG,
+	.cs[3].config = CONFIG_SYS_DDR_CS3_CONFIG,
+	.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_800,
+	.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_800,
+	.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_800,
+	.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_800,
+	.ddr_sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG,
+	.ddr_sdram_cfg_2 = CONFIG_SYS_DDR_SDRAM_CFG2,
+	.ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_800,
+	.ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_800,
+	.ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL,
+	.ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_800,
+	.ddr_data_init = CONFIG_MEM_INIT_VALUE,
+	.ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_800,
+	.ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR,
+	.ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR,
+	.timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4,
+	.timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5,
+	.ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CNTL,
+	.ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CNTL,
+	.ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1,
+	.ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2
+};
+
+fsl_ddr_cfg_regs_t ddr_cfg_regs_900 = {
+	.cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS,
+	.cs[1].bnds = CONFIG_SYS_DDR_CS1_BNDS,
+	.cs[2].bnds = CONFIG_SYS_DDR_CS2_BNDS,
+	.cs[3].bnds = CONFIG_SYS_DDR_CS3_BNDS,
+	.cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG,
+	.cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2,
+	.cs[1].config = CONFIG_SYS_DDR_CS1_CONFIG,
+	.cs[2].config = CONFIG_SYS_DDR_CS2_CONFIG,
+	.cs[3].config = CONFIG_SYS_DDR_CS3_CONFIG,
+	.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_900,
+	.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_900,
+	.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_900,
+	.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_900,
+	.ddr_sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG,
+	.ddr_sdram_cfg_2 = CONFIG_SYS_DDR_SDRAM_CFG2,
+	.ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_900,
+	.ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_900,
+	.ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL,
+	.ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_900,
+	.ddr_data_init = CONFIG_MEM_INIT_VALUE,
+	.ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_900,
+	.ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR,
+	.ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR,
+	.timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4,
+	.timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5,
+	.ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CNTL,
+	.ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CNTL,
+	.ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1,
+	.ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2
+};
+
+fsl_ddr_cfg_regs_t ddr_cfg_regs_1000 = {
+	.cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS,
+	.cs[1].bnds = CONFIG_SYS_DDR_CS1_BNDS,
+	.cs[2].bnds = CONFIG_SYS_DDR_CS2_BNDS,
+	.cs[3].bnds = CONFIG_SYS_DDR_CS3_BNDS,
+	.cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG,
+	.cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2,
+	.cs[1].config = CONFIG_SYS_DDR_CS1_CONFIG,
+	.cs[2].config = CONFIG_SYS_DDR_CS2_CONFIG,
+	.cs[3].config = CONFIG_SYS_DDR_CS3_CONFIG,
+	.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_1000,
+	.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_1000,
+	.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_1000,
+	.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_1000,
+	.ddr_sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG,
+	.ddr_sdram_cfg_2 = CONFIG_SYS_DDR_SDRAM_CFG2,
+	.ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_1000,
+	.ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_1000,
+	.ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL,
+	.ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_1000,
+	.ddr_data_init = CONFIG_MEM_INIT_VALUE,
+	.ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_1000,
+	.ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR,
+	.ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR,
+	.timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4,
+	.timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5,
+	.ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CNTL,
+	.ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CNTL,
+	.ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1,
+	.ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2
+};
+
+fsl_ddr_cfg_regs_t ddr_cfg_regs_1200 = {
+	.cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS,
+	.cs[1].bnds = CONFIG_SYS_DDR_CS1_BNDS,
+	.cs[2].bnds = CONFIG_SYS_DDR_CS2_BNDS,
+	.cs[3].bnds = CONFIG_SYS_DDR_CS3_BNDS,
+	.cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG,
+	.cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2,
+	.cs[1].config = CONFIG_SYS_DDR_CS1_CONFIG,
+	.cs[2].config = CONFIG_SYS_DDR_CS2_CONFIG,
+	.cs[3].config = CONFIG_SYS_DDR_CS3_CONFIG,
+	.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_1200,
+	.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_1200,
+	.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_1200,
+	.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_1200,
+	.ddr_sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG,
+	.ddr_sdram_cfg_2 = CONFIG_SYS_DDR_SDRAM_CFG2,
+	.ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_1200,
+	.ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_1200,
+	.ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL,
+	.ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_1200,
+	.ddr_data_init = CONFIG_MEM_INIT_VALUE,
+	.ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_1200,
+	.ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR,
+	.ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR,
+	.timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4,
+	.timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5,
+	.ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CNTL,
+	.ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CNTL,
+	.ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1,
+	.ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2
+};
+
+fixed_ddr_parm_t fixed_ddr_parm_0[] = {
+	{750, 850, &ddr_cfg_regs_800},
+	{850, 950, &ddr_cfg_regs_900},
+	{950, 1050, &ddr_cfg_regs_1000},
+	{1050, 1250, &ddr_cfg_regs_1200},
+	{0, 0, NULL}
+};
diff --git a/board/freescale/p3060qds/p3060qds.c b/board/freescale/p3060qds/p3060qds.c
new file mode 100644
index 0000000..c6c74f2
--- /dev/null
+++ b/board/freescale/p3060qds/p3060qds.c
@@ -0,0 +1,341 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <fm_eth.h>
+#include <configs/P3060QDS.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+
+#include "../common/qixis.h"
+#include "p3060qds.h"
+#include "p3060qds_qixis.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+	u8 sw;
+	struct cpu_type *cpu = gd->cpu;
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+	unsigned int i;
+
+	printf("Board: %s", cpu->name);
+	puts("QDS, ");
+
+	printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
+		QIXIS_READ(id), QIXIS_READ(arch), QIXIS_READ(scver));
+
+	sw = QIXIS_READ(brdcfg[0]);
+	sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
+
+	if (sw < 0x8)
+		printf("vBank: %d\n", sw);
+	else if (sw == 0x8)
+		puts("Promjet\n");
+	else if (sw == 0x9)
+		puts("NAND\n");
+	else
+		printf("invalid setting of SW%u\n", PIXIS_LBMAP_SWITCH);
+
+#ifdef CONFIG_PHYS_64BIT
+	puts("36-bit Addressing\n");
+#endif
+	puts("Reset Configuration Word (RCW):");
+	for (i = 0; i < ARRAY_SIZE(gur->rcwsr); i++) {
+		u32 rcw = in_be32(&gur->rcwsr[i]);
+
+		if ((i % 4) == 0)
+			printf("\n       %08x:", i * 4);
+		printf(" %08x", rcw);
+	}
+	puts("\n");
+
+	puts("SERDES Reference Clocks: ");
+	sw = QIXIS_READ(brdcfg[2]);
+	for (i = 0; i < 3; i++) {
+		static const char * const freq[] = {"100", "125", "Reserved",
+						"156.25"};
+		unsigned int clock = (sw >> (2 * i)) & 3;
+
+		printf("Bank%u=%sMhz ", i+1, freq[clock]);
+	}
+	puts("\n");
+
+	return 0;
+}
+
+int board_early_init_f(void)
+{
+	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+
+	/* only single DDR controller on QDS board, disable DDR1_MCK4/5 */
+	setbits_be32(&gur->ddrclkdr, 0x00030000);
+
+	return 0;
+}
+
+void board_config_serdes_mux(void)
+{
+	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	int cfg = (in_be32(&gur->rcwsr[4]) &
+			FSL_CORENET_RCWSR4_SRDS_PRTCL) >> 26;
+
+	switch (cfg) {
+	case 0x03:
+	case 0x06:
+		/* set Lane I,J as SGMII */
+		QIXIS_WRITE(brdcfg[6], BRDCFG6_SD4MX_B | BRDCFG6_SD3MX_A |
+				       BRDCFG6_SD2MX_B | BRDCFG6_SD1MX_A);
+		break;
+	case 0x16:
+	case 0x19:
+	case 0x1c:
+		/* set Lane I,J as Aurora Debug */
+		QIXIS_WRITE(brdcfg[6], BRDCFG6_SD4MX_A | BRDCFG6_SD3MX_B |
+				       BRDCFG6_SD2MX_A | BRDCFG6_SD1MX_B);
+		break;
+	default:
+		puts("Invalid SerDes protocol for P3060QDS\n");
+		break;
+	}
+}
+
+void board_config_usb_mux(void)
+{
+	u8 brdcfg4, brdcfg5, brdcfg7;
+	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	u32 rcwsr11 = in_be32(&gur->rcwsr[11]);
+	u32 ec1 = rcwsr11 & FSL_CORENET_RCWSR11_EC1;
+	u32 ec2 = rcwsr11 & FSL_CORENET_RCWSR11_EC2;
+
+	brdcfg4 = QIXIS_READ(brdcfg[4]);
+	brdcfg4 &= ~BRDCFG4_EC_MODE_MASK;
+	if ((ec1 == FSL_CORENET_RCWSR11_EC1_FM1_USB1) &&
+		 (ec2 == FSL_CORENET_RCWSR11_EC2_USB2)) {
+		brdcfg4 |= BRDCFG4_EC2_USB_EC1_USB;
+
+	} else if ((ec1 == FSL_CORENET_RCWSR11_EC1_FM1_USB1) &&
+		 ((ec2 == FSL_CORENET_RCWSR11_EC2_FM1_DTSEC2) ||
+		 (ec2 == FSL_CORENET_RCWSR11_EC2_FM2_DTSEC1))) {
+		brdcfg4 |= BRDCFG4_EC2_RGMII_EC1_USB;
+
+	} else if ((ec1 == FSL_CORENET_RCWSR11_EC1_FM1_DTSEC1) &&
+		 (ec2 == FSL_CORENET_RCWSR11_EC2_USB2)) {
+		brdcfg4 |= BRDCFG4_EC2_USB_EC1_RGMII;
+
+	} else if ((ec1 == FSL_CORENET_RCWSR11_EC1_FM1_DTSEC1) &&
+		 ((ec2 == FSL_CORENET_RCWSR11_EC2_FM1_DTSEC2) ||
+		 (ec2 == FSL_CORENET_RCWSR11_EC2_FM2_DTSEC1))) {
+		brdcfg4 |= BRDCFG4_EC2_RGMII_EC1_RGMII;
+	} else {
+		brdcfg4 |= BRDCFG4_EC2_MII_EC1_MII;
+	}
+	QIXIS_WRITE(brdcfg[4], brdcfg4);
+
+	brdcfg5 = QIXIS_READ(brdcfg[5]);
+	brdcfg5 &= ~(BRDCFG5_USB1ID_MASK | BRDCFG5_USB2ID_MASK);
+	brdcfg5 |= (BRDCFG5_USB1ID_CTRL | BRDCFG5_USB2ID_CTRL);
+	QIXIS_WRITE(brdcfg[5], brdcfg5);
+
+	brdcfg7 = BRDCFG7_JTAGMX_COP_JTAG | BRDCFG7_IQ1MX_IRQ_EVT |
+		BRDCFG7_G1MX_USB1 | BRDCFG7_D1MX_TSEC3USB | BRDCFG7_I3MX_USB1;
+	QIXIS_WRITE(brdcfg[7], brdcfg7);
+}
+
+int board_early_init_r(void)
+{
+	const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+	const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+	/*
+	 * Remap Boot flash + PROMJET region to caching-inhibited
+	 * so that flash can be erased properly.
+	 */
+
+	/* Flush d-cache and invalidate i-cache of any FLASH data */
+	flush_dcache();
+	invalidate_icache();
+
+	/* invalidate existing TLB entry for flash + promjet */
+	disable_tlb(flash_esel);
+
+	set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, flash_esel, BOOKE_PAGESZ_256M, 1);
+
+	set_liodns();
+#ifdef CONFIG_SYS_DPAA_QBMAN
+	setup_portals();
+#endif
+	board_config_serdes_mux();
+	board_config_usb_mux();
+
+	return 0;
+}
+
+static const char *serdes_clock_to_string(u32 clock)
+{
+	switch (clock) {
+	case SRDS_PLLCR0_RFCK_SEL_100:
+		return "100";
+	case SRDS_PLLCR0_RFCK_SEL_125:
+		return "125";
+	case SRDS_PLLCR0_RFCK_SEL_156_25:
+		return "156.25";
+	default:
+		return "150";
+	}
+}
+
+#define NUM_SRDS_BANKS	3
+
+int misc_init_r(void)
+{
+	serdes_corenet_t *srds_regs;
+	u32 actual[NUM_SRDS_BANKS];
+	unsigned int i;
+	u8 sw;
+
+	sw = QIXIS_READ(brdcfg[2]);
+	for (i = 0; i < 3; i++) {
+		unsigned int clock = (sw >> (2 * i)) & 3;
+		switch (clock) {
+		case 0:
+			actual[i] = SRDS_PLLCR0_RFCK_SEL_100;
+			break;
+		case 1:
+			actual[i] = SRDS_PLLCR0_RFCK_SEL_125;
+			break;
+		case 3:
+			actual[i] = SRDS_PLLCR0_RFCK_SEL_156_25;
+			break;
+		default:
+			printf("Warning: SDREFCLK%u switch setting of '10' is "
+				"unsupported\n", i + 1);
+			break;
+		}
+	}
+
+	srds_regs = (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR;
+	for (i = 0; i < NUM_SRDS_BANKS; i++) {
+		u32 pllcr0 = in_be32(&srds_regs->bank[i].pllcr0);
+		u32 expected = pllcr0 & SRDS_PLLCR0_RFCK_SEL_MASK;
+		if (expected != actual[i]) {
+			printf("Warning: SERDES bank %u expects reference clock"
+			       " %sMHz, but actual is %sMHz\n", i + 1,
+			       serdes_clock_to_string(expected),
+			       serdes_clock_to_string(actual[i]));
+		}
+	}
+
+	return 0;
+}
+
+/*
+ * This is map of CVDD values. 33 means CVDD is 3.3v, 25 means CVDD is 2.5v,
+ * 18 means CVDD is 1.8v.
+ */
+static u8 IO_VSEL[] = {
+	33, 33, 33, 25, 25, 25, 18, 18, 18,
+	33, 33, 33, 25, 25, 25, 18, 18, 18,
+	33, 33, 33, 25, 25, 25, 18, 18, 18,
+	33, 33, 33, 33, 33
+};
+
+#define IO_VSEL_MASK	0x1f
+
+/*
+ * different CVDD selects diffenert spi flashs, read dutcfg[3] to get CVDD,
+ * then set status of  spi flash nodes to 'disabled' according to CVDD.
+ * CVDD '33' will select spi flash0 and flash1, CVDD '25' will select spi
+ * flash2, CVDD '18' will select spi flash3.
+ */
+void fdt_fixup_board_spi(void *blob)
+{
+	u8 sw5 = QIXIS_READ(dutcfg[3]);
+
+	switch (IO_VSEL[sw5 & IO_VSEL_MASK]) {
+	/* 3.3v */
+	case 33:
+		do_fixup_by_compat(blob, "atmel,at45db081d", "status",
+				"disabled", strlen("disabled") + 1, 1);
+		do_fixup_by_compat(blob, "spansion,sst25wf040", "status",
+				"disabled", strlen("disabled") + 1, 1);
+		break;
+	/* 2.5v */
+	case 25:
+		do_fixup_by_compat(blob, "spansion,s25sl12801", "status",
+				"disabled", strlen("disabled") + 1, 1);
+		do_fixup_by_compat(blob, "spansion,en25q32", "status",
+				"disabled", strlen("disabled") + 1, 1);
+		do_fixup_by_compat(blob, "spansion,sst25wf040", "status",
+				"disabled", strlen("disabled") + 1, 1);
+		break;
+	/* 1.8v */
+	case 18:
+		do_fixup_by_compat(blob, "spansion,s25sl12801", "status",
+				"disabled", strlen("disabled") + 1, 1);
+		do_fixup_by_compat(blob, "spansion,en25q32", "status",
+				"disabled", strlen("disabled") + 1, 1);
+		do_fixup_by_compat(blob, "atmel,at45db081d", "status",
+				"disabled", strlen("disabled") + 1, 1);
+		break;
+	}
+}
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	phys_addr_t base;
+	phys_size_t size;
+
+	ft_cpu_setup(blob, bd);
+
+	base = getenv_bootm_low();
+	size = getenv_bootm_size();
+
+	fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+	pci_of_setup(blob, bd);
+#endif
+
+	fdt_fixup_liodn(blob);
+	fdt_fixup_dr_usb(blob, bd);
+	fdt_fixup_board_spi(blob);
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+	fdt_fixup_fman_ethernet(blob);
+	fdt_fixup_board_enet(blob);
+#endif
+}
diff --git a/board/freescale/p3060qds/p3060qds.h b/board/freescale/p3060qds/p3060qds.h
new file mode 100644
index 0000000..3da6815
--- /dev/null
+++ b/board/freescale/p3060qds/p3060qds.h
@@ -0,0 +1,30 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __P3060QDS_H__
+#define __P3060QDS_H__
+
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/u-boot.h>
+
+void fdt_fixup_board_enet(void *blob);
+void pci_of_setup(void *blob, bd_t *bd);
+extern fixed_ddr_parm_t fixed_ddr_parm_0[];
+
+#endif
diff --git a/board/freescale/p3060qds/p3060qds_qixis.h b/board/freescale/p3060qds/p3060qds_qixis.h
new file mode 100644
index 0000000..4d5d6a2
--- /dev/null
+++ b/board/freescale/p3060qds/p3060qds_qixis.h
@@ -0,0 +1,74 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __P3060QDS_QIXIS_H__
+#define __P3060QDS_QIXIS_H__
+
+/* Definitions of QIXIS Registers for P3060QDS */
+
+/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */
+#define BRDCFG4_EC_MODE_MASK		0x0F
+#define BRDCFG4_EC2_MII_EC1_MII	0x00
+#define BRDCFG4_EC2_MII_EC1_USB	0x03
+#define BRDCFG4_EC2_USB_EC1_MII	0x0C
+#define BRDCFG4_EC2_USB_EC1_USB	0x0F
+#define BRDCFG4_EC2_USB_EC1_RGMII	0x0E
+#define BRDCFG4_EC2_RGMII_EC1_USB	0x0B
+#define BRDCFG4_EC2_RGMII_EC1_RGMII	0x0A
+#define BRDCFG4_EMISEL_MASK		0xF0
+
+#define BRDCFG5_ECLKS_MASK		0x80
+#define BRDCFG5_USB1ID_MASK		0x40
+#define BRDCFG5_USB2ID_MASK		0x20
+#define BRDCFG5_GC2MX_MASK		0x0C
+#define BRDCFG5_T15MX_MASK		0x03
+#define BRDCFG5_ECLKS_IEEE1588_CM	0x80
+#define BRDCFG5_USB1ID_CTRL		0x40
+#define BRDCFG5_USB2ID_CTRL		0x20
+
+#define BRDCFG6_SD1MX_A		0x01
+#define BRDCFG6_SD1MX_B		0x00
+#define BRDCFG6_SD2MX_A		0x02
+#define BRDCFG6_SD2MX_B		0x00
+#define BRDCFG6_SD3MX_A		0x04
+#define BRDCFG6_SD3MX_B		0x00
+#define BRDCFG6_SD4MX_A		0x08
+#define BRDCFG6_SD4MX_B		0x00
+
+#define BRDCFG7_JTAGMX_MASK		0xC0
+#define BRDCFG7_IQ1MX_MASK		0x20
+#define BRDCFG7_G1MX_MASK		0x10
+#define BRDCFG7_D1MX_MASK		0x0C
+#define BRDCFG7_I3MX_MASK		0x03
+#define BRDCFG7_JTAGMX_AURORA		0x00
+#define BRDCFG7_JTAGMX_FPGA		0x80
+#define BRDCFG7_JTAGMX_COP_JTAG	0xC0
+#define BRDCFG7_IQ1MX_IRQ_EVT		0x00
+#define BRDCFG7_IQ1MX_USB2		0x20
+#define BRDCFG7_G1MX_USB1		0x00
+#define BRDCFG7_G1MX_TSEC3		0x10
+#define BRDCFG7_D1MX_DMA		0x00
+#define BRDCFG7_D1MX_TSEC3USB		0x04
+#define BRDCFG7_D1MX_HDLC2		0x08
+#define BRDCFG7_I3MX_UART2_I2C34	0x00
+#define BRDCFG7_I3MX_GPIO_EVT		0x01
+#define BRDCFG7_I3MX_USB1		0x02
+#define BRDCFG7_I3MX_TSEC3		0x03
+
+#endif