ARM: zynq: ehci: Added USB host driver support

Added USB host driver for zynq.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

2 files changed, 105 insertions, 0 deletions

diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index b301e28..7211c6a 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -37,6 +37,7 @@ obj-$(CONFIG_USB_EHCI_SPEAR) += ehci-spear.o
 obj-$(CONFIG_USB_EHCI_TEGRA) += ehci-tegra.o
 obj-$(CONFIG_USB_EHCI_VCT) += ehci-vct.o
 obj-$(CONFIG_USB_EHCI_RMOBILE) += ehci-rmobile.o
+obj-$(CONFIG_USB_EHCI_ZYNQ) += ehci-zynq.o
 
 # xhci
 obj-$(CONFIG_USB_XHCI) += xhci.o xhci-mem.o xhci-ring.o
diff --git a/drivers/usb/host/ehci-zynq.c b/drivers/usb/host/ehci-zynq.c
new file mode 100644
index 0000000..7770d05
--- /dev/null
+++ b/drivers/usb/host/ehci-zynq.c
@@ -0,0 +1,104 @@
+/*
+ * (C) Copyright 2014, Xilinx, Inc
+ *
+ * USB Low level initialization(Specific to zynq)
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/io.h>
+#include <usb.h>
+#include <usb/ehci-fsl.h>
+#include <usb/ulpi.h>
+
+#include "ehci.h"
+
+#define ZYNQ_USB_USBCMD_RST			0x0000002
+#define ZYNQ_USB_USBCMD_STOP			0x0000000
+#define ZYNQ_USB_NUM_MIO			12
+
+/*
+ * Create the appropriate control structures to manage
+ * a new EHCI host controller.
+ */
+int ehci_hcd_init(int index,  enum usb_init_type init, struct ehci_hccr **hccr,
+		  struct ehci_hcor **hcor)
+{
+	struct usb_ehci *ehci;
+	struct ulpi_viewport ulpi_vp;
+	int ret, mio_usb;
+	/* Used for writing the ULPI data address */
+	struct ulpi_regs *ulpi = (struct ulpi_regs *)0;
+
+	if (!index) {
+		mio_usb = zynq_slcr_get_mio_pin_status("usb0");
+		if (mio_usb != ZYNQ_USB_NUM_MIO) {
+			printf("usb0 wrong num MIO: %d, Index %d\n", mio_usb,
+			       index);
+			return -1;
+		}
+		ehci = (struct usb_ehci *)ZYNQ_USB_BASEADDR0;
+	} else {
+		mio_usb = zynq_slcr_get_mio_pin_status("usb1");
+		if (mio_usb != ZYNQ_USB_NUM_MIO) {
+			printf("usb1 wrong num MIO: %d, Index %d\n", mio_usb,
+			       index);
+			return -1;
+		}
+		ehci = (struct usb_ehci *)ZYNQ_USB_BASEADDR1;
+	}
+
+	*hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
+	*hcor = (struct ehci_hcor *)((uint32_t) *hccr +
+			HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
+
+	ulpi_vp.viewport_addr = (u32)&ehci->ulpi_viewpoint;
+	ulpi_vp.port_num = 0;
+
+	ret = ulpi_init(&ulpi_vp);
+	if (ret) {
+		puts("zynq ULPI viewport init failed\n");
+		return -1;
+	}
+
+	/* ULPI set flags */
+	ulpi_write(&ulpi_vp, &ulpi->otg_ctrl,
+		   ULPI_OTG_DP_PULLDOWN | ULPI_OTG_DM_PULLDOWN |
+		   ULPI_OTG_EXTVBUSIND);
+	ulpi_write(&ulpi_vp, &ulpi->function_ctrl,
+		   ULPI_FC_FULL_SPEED | ULPI_FC_OPMODE_NORMAL |
+		   ULPI_FC_SUSPENDM);
+	ulpi_write(&ulpi_vp, &ulpi->iface_ctrl, 0);
+
+	/* Set VBus */
+	ulpi_write(&ulpi_vp, &ulpi->otg_ctrl_set,
+		   ULPI_OTG_DRVVBUS | ULPI_OTG_DRVVBUS_EXT);
+
+	return 0;
+}
+
+/*
+ * Destroy the appropriate control structures corresponding
+ * the the EHCI host controller.
+ */
+int ehci_hcd_stop(int index)
+{
+	struct usb_ehci *ehci;
+
+	if (!index)
+		ehci = (struct usb_ehci *)ZYNQ_USB_BASEADDR0;
+	else
+		ehci = (struct usb_ehci *)ZYNQ_USB_BASEADDR1;
+
+	/* Stop controller */
+	writel(ZYNQ_USB_USBCMD_STOP, &ehci->usbcmd);
+	udelay(1000);
+
+	/* Initiate controller reset */
+	writel(ZYNQ_USB_USBCMD_RST, &ehci->usbcmd);
+
+	return 0;
+}