Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm:
  Arm: re-introduce the MACH_TYPE_XXXXXX for EB_CPUX9K2 board
  arm: jadecpu: Readd MACH_TYPE_JADECPU
  at91: defined mach-types for otc570 board in board config file
  at91: defined mach-types for meesc board in board config file
  mx31pdk: Enable D and I caches
  ehci-mxc: remove incorrect comment
  README: Fix supported i.MX SoC list for CONFIG_MXC_SPI
  mx53: Turn off child clocks before reconfigure perclk_root
  qong: enable support for compressed images
  imx: imx31_phycore.h: fix checkpatch warnings
  vision2: Remove unused get_board_rev function
  mx53smd: Remove unused get_board_rev function
  mx53ard: Remove unused get_board_rev function
  mx53evk: Remove unused get_board_rev function
  mx53evk: Add RTC support
  mx53loco: Remove unused get_board_rev function
  mx53evk: Remove unneeded '1' from mx53evk.h
  OMAP3: mvblx: Initial support for mvBlueLYNX-X
  ARM: dig297: Define MACH_TYPE_OMAP3_CPS and CONFIG_MACH_TYPE
  omap3: mem: Move comments next to definitions
  omap3: mem: Clean-up whitespaces
  omap3: mem: Define and use common macros
  Davinci: ea20: added PREBOOT to configuration
  Davinci: ea20: added I2C support
  Davinci: ea20: added video support
  VIDEO: davinci: add framebuffer to da8xx
  ARM: Davinci: added missing registers to hardware.h
  Davinci: ea20: add gpios for LCD backlight control
  Davinci: ea20: add gpio for keeping power on in board_late_init
  Davinci: ea20: Add default U-Boot environment
  Davinci: ea20: Add early init to get early output from console
  Davinci: ea20: Add NAND support
  Davinci: ea20: set GPIOs to hold MII-Phy in reset and set UART0-Switch for console
  Davinci: ea20: set console on UART0
  arm, davinci: add cam_enc_4xx support
  arm926ejs, davinci: add missing spi defines for dm365
  arm926ejs, davinci: add cpuinfo for dm365
  arm, davinci: add lowlevel function for dm365 soc
  arm, davinci: add header files for dm365
  spl, nand: add 4bit HW ecc oob first nand_read_page function
  arm, davinci: add support for new spl framework
  spl: add option for adding post memory test to the SPL framework
  net, davinci_emac: make clock divider in MDIO control register configurable
  arm, usb, davinci: make USBPHY_CTL register configurable
  usb, davinci: add enable_vbus() weak function
  omap3evm: fix errors caused by multiple definitions
  omap3evm: Add (quick) configuration for NAND only
  omap3evm: Add (quick) configuration for MMC/SD only
  omap3evm: move common config options to new file
  omap3evm: Prepare to split configuration
  omap3evm: Reorder related config options
  omap/spl: actually enable the console
  davinci_emac: compilation fix, phy is array now
  omap3evm: Set environment variable 'ethaddr'
  arm, arm926: fix missing symbols in NAND_SPL mode
  arm, davinci: Add function lpsc_syncreset()
  arm, davinci: replace CONFIG_PRELOADER with CONFIG_SPL_BUILD
  arm/km: portl2 environment address update to P1B
  arm/km: adapt bootcounter evaluation
  arm/km: enable jffs2 cmds
  arm/km: trigger reconfiguration for the Xilinx FPGA
  arm/km: add boardid and hwkey to kernel command line
  ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boards
  netspace_v2: enable I2C EEPROM support
  netspace_v2: fix SDRAM configuration
  armada100: define CONFIG_SYS_CACHELINE_SIZE
  pantheon: define CONFIG_SYS_CACHELINE_SIZE
  kirkwood: define CONFIG_SYS_CACHELINE_SIZE
  kirkwood: drop empty asm-offsets.s file
  arm/km/mgcoge3un: enhance "waitforne" feature
  arm/km: add variable waitforne to mgcoge3un
  gplugD: Fix for error:MACH_TYPE_SHEEVAD undeclared
  ARM: dreamplug: fix compilation
  ARM: DockStar: fix compilation
  ARM: netspace_v2: fix warnings
  am335x: Drop board_sysinfo struct
  am335x: Temporarily add MACH_TYPE define
  misc:pmic:samsung Enable PMIC driver at C210 Universal target
  dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p UNIVERSAL C210 target
  dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p GONI target
  smdkv310: use macro for mmc data read function address
  smdkv310: use spl framework for mmc spl
  SMDKV310: use get_ram_size() to validate dram size
  SMDKV310: Initialize board id using CONFIG_MACH_TYPE
  ORIGEN : use absolute paths and fix tool naming
  ORIGEN : enable device tree support
  MX25: tx25: Fix building due to missing MACH_TYPE
  mx31: Add board support for HALE TT-01
  mx31: add ESD control registers
  mx31: define pins and init for UART2 and CSPI3
  MX35: add support for flea3 board
  MX51: vision2: add MACH_TYPE in config file
  vision2: Remove unused header file
  mx51evk: Remove unused get_board_rev function
  mx51evk: Remove unneeded '1' from mx51evk.h
  I2C: Fix mxc_i2c.c problem on imx31_phycore
  mx35pdk: Add RTC support
  mx51evk: Use GPIO API for configuring the IOMUX
  mx51evk: Add RTC support
  rtc: Make mc13783-rtc driver generic
  qong: remove unneeded IOMUX settings
  qong: Use mx31_set_gpr to setup USBH2 pins
  mx31: Introduce mx31_set_gpr function
  mx31pdk: Add MC13783 PMIC support
  qong: remove unneeded "1" from qong.h
  misc: pmic: fix regression in pmic_fsl.c (SPI)
  mx5 configs: CONFIG_PRIME should really be CONFIG_ETHPRIME
  MX35: Drop unnecessary prototypes from imx-regs.h
  I2C: added I2C-2 and I2C-3 to MX35
  MX35: factorize common assembly code
  MX35: add reset cause as provided by other i.MX
  MX35: add pins definition for UART3
  MX35: added ESDC structure to imx-regs

1 files changed, 292 insertions, 0 deletions

diff --git a/include/configs/omap3_evm_common.h b/include/configs/omap3_evm_common.h
new file mode 100644
index 0000000..54aa7a7
--- /dev/null
+++ b/include/configs/omap3_evm_common.h
@@ -0,0 +1,292 @@
+/*
+ * Common configuration settings for the TI OMAP3 EVM board.
+ *
+ * Copyright (C) 2006-2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __OMAP3_EVM_COMMON_H
+#define __OMAP3_EVM_COMMON_H
+
+/*
+ * High level configuration options
+ */
+#define CONFIG_OMAP			/* This is TI OMAP core */
+#define CONFIG_OMAP34XX			/* belonging to 34XX family */
+#define CONFIG_OMAP3430			/* which is in a 3430 */
+
+#define CONFIG_SDRC			/* The chip has SDRC controller */
+
+#define CONFIG_OMAP3_EVM		/* This is a OMAP3 EVM */
+#define CONFIG_OMAP3_MICRON_DDR		/* with MICRON DDR part */
+#define CONFIG_TWL4030_POWER		/* with TWL4030 PMIC */
+
+#undef CONFIG_USE_IRQ			/* no support for IRQs */
+
+/*
+ * Clock related definitions
+ */
+#define V_OSCK			26000000	/* Clock output from T2 */
+#define V_SCLK			(V_OSCK >> 1)
+
+/*
+ * OMAP3 has 12 GP timers, they can be driven by the system clock
+ * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
+ * This rate is divided by a local divisor.
+ */
+#define CONFIG_SYS_TIMERBASE		OMAP34XX_GPT2
+#define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */
+#define CONFIG_SYS_HZ			1000
+
+/* Size of environment - 128KB */
+#define CONFIG_ENV_SIZE			(128 << 10)
+
+/* Size of malloc pool */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (128 << 10))
+
+/*
+ * Stack sizes
+ * These values are used in start.S
+ */
+#define CONFIG_STACKSIZE	(128 << 10)	/* regular stack 128 KiB */
+
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ	(4 << 10)	/* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ	(4 << 10)	/* FIQ stack 4 KiB */
+#endif
+
+/*
+ * Physical Memory Map
+ * Note 1: CS1 may or may not be populated
+ * Note 2: SDRAM size is expected to be at least 32MB
+ */
+#define CONFIG_NR_DRAM_BANKS		2
+#define PHYS_SDRAM_1			OMAP34XX_SDRC_CS0
+#define PHYS_SDRAM_1_SIZE		(32 << 20)
+#define PHYS_SDRAM_2			OMAP34XX_SDRC_CS1
+
+/* SDRAM Bank Allocation method */
+#define SDRC_R_B_C
+
+/* Limits for memtest */
+#define CONFIG_SYS_MEMTEST_START	(OMAP34XX_SDRC_CS0)
+#define CONFIG_SYS_MEMTEST_END		(OMAP34XX_SDRC_CS0 + \
+						0x01F00000) /* 31MB */
+
+/* Default load address */
+#define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0)
+
+/* -----------------------------------------------------------------------------
+ * Hardware drivers
+ * -----------------------------------------------------------------------------
+ */
+
+/*
+ * NS16550 Configuration
+ */
+#define V_NS16550_CLK			48000000	/* 48MHz (APLL96/2) */
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
+#define CONFIG_SYS_NS16550_CLK		V_NS16550_CLK
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_SERIAL1			1	/* UART1 on OMAP3 EVM */
+#define CONFIG_SYS_NS16550_COM1		OMAP34XX_UART1
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600,\
+					115200}
+
+/*
+ * I2C
+ */
+#define CONFIG_HARD_I2C
+#define CONFIG_DRIVER_OMAP34XX_I2C
+
+#define CONFIG_SYS_I2C_SPEED		100000
+#define CONFIG_SYS_I2C_SLAVE		1
+#define CONFIG_SYS_I2C_BUS		0
+#define CONFIG_SYS_I2C_BUS_SELECT	1
+
+/*
+ * PISMO support
+ */
+#define PISMO1_NAND_SIZE		GPMC_SIZE_128M
+#define PISMO1_ONEN_SIZE		GPMC_SIZE_128M
+
+/* Monitor at start of flash - Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
+
+#define CONFIG_SYS_MONITOR_LEN		(256 << 10)
+
+/* Start location & size of environment */
+#define ONENAND_ENV_OFFSET		0x260000
+#define SMNAND_ENV_OFFSET		0x260000
+
+#define CONFIG_SYS_ENV_SECT_SIZE	(128 << 10)	/* 128 KiB */
+
+/*
+ * NAND
+ */
+/* Physical address to access NAND */
+#define CONFIG_SYS_NAND_ADDR		NAND_BASE
+
+/* Physical address to access NAND at CS0 */
+#define CONFIG_SYS_NAND_BASE		NAND_BASE
+
+/* Max number of NAND devices */
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+
+/* Timeout values (in ticks) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	(100 * CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT	(100 * CONFIG_SYS_HZ)
+
+/* Flash banks JFFS2 should use */
+#define CONFIG_SYS_MAX_MTD_BANKS	(CONFIG_SYS_MAX_FLASH_BANKS + \
+						CONFIG_SYS_MAX_NAND_DEVICE)
+
+#define CONFIG_SYS_JFFS2_MEM_NAND
+#define CONFIG_SYS_JFFS2_FIRST_BANK	CONFIG_SYS_MAX_FLASH_BANKS
+#define CONFIG_SYS_JFFS2_NUM_BANKS	1
+
+#define CONFIG_JFFS2_NAND
+/* nand device jffs2 lives on */
+#define CONFIG_JFFS2_DEV		"nand0"
+/* Start of jffs2 partition */
+#define CONFIG_JFFS2_PART_OFFSET	0x680000
+/* Size of jffs2 partition */
+#define CONFIG_JFFS2_PART_SIZE		0xf980000
+
+/*
+ * USB
+ */
+#ifdef CONFIG_USB_OMAP3
+
+#ifdef CONFIG_MUSB_HCD
+#define CONFIG_CMD_USB
+
+#define CONFIG_USB_STORAGE
+#define CONGIG_CMD_STORAGE
+#define CONFIG_CMD_FAT
+
+#ifdef CONFIG_USB_KEYBOARD
+#define CONFIG_SYS_USB_EVENT_POLL
+#define CONFIG_PREBOOT			"usb start"
+#endif /* CONFIG_USB_KEYBOARD */
+
+#endif /* CONFIG_MUSB_HCD */
+
+#ifdef CONFIG_MUSB_UDC
+/* USB device configuration */
+#define CONFIG_USB_DEVICE
+#define CONFIG_USB_TTY
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+
+/* Change these to suit your needs */
+#define CONFIG_USBD_VENDORID		0x0451
+#define CONFIG_USBD_PRODUCTID		0x5678
+#define CONFIG_USBD_MANUFACTURER	"Texas Instruments"
+#define CONFIG_USBD_PRODUCT_NAME	"EVM"
+#endif /* CONFIG_MUSB_UDC */
+
+#endif /* CONFIG_USB_OMAP3 */
+
+/* ----------------------------------------------------------------------------
+ * U-boot features
+ * ----------------------------------------------------------------------------
+ */
+#define CONFIG_SYS_PROMPT		"OMAP3_EVM # "
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+#define CONFIG_SYS_MAXARGS		16	/* max args for a command */
+
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_CMDLINE_TAG			/* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+
+/* Size of Console IO buffer */
+#define CONFIG_SYS_CBSIZE		512
+
+/* Size of print buffer */
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+						sizeof(CONFIG_SYS_PROMPT) + 16)
+
+/* Size of bootarg buffer */
+#define CONFIG_SYS_BARGSIZE		(CONFIG_SYS_CBSIZE)
+
+#define CONFIG_BOOTFILE			"uImage"
+
+/*
+ * NAND / OneNAND
+ */
+#if defined(CONFIG_CMD_NAND)
+#define CONFIG_SYS_FLASH_BASE		PISMO1_NAND_BASE
+
+#define CONFIG_NAND_OMAP_GPMC
+#define GPMC_NAND_ECC_LP_x16_LAYOUT
+#define CONFIG_ENV_OFFSET		SMNAND_ENV_OFFSET
+#elif defined(CONFIG_CMD_ONENAND)
+#define CONFIG_SYS_FLASH_BASE		PISMO1_ONEN_BASE
+#define CONFIG_SYS_ONENAND_BASE		ONENAND_MAP
+#endif
+
+#if !defined(CONFIG_ENV_IS_NOWHERE)
+#if defined(CONFIG_CMD_NAND)
+#define CONFIG_ENV_IS_IN_NAND
+#elif defined(CONFIG_CMD_ONENAND)
+#define CONFIG_ENV_IS_IN_ONENAND
+#define CONFIG_ENV_OFFSET		ONENAND_ENV_OFFSET
+#endif
+#endif /* CONFIG_ENV_IS_NOWHERE */
+
+#define CONFIG_ENV_ADDR			CONFIG_ENV_OFFSET
+
+#if defined(CONFIG_CMD_NET)
+
+/* Ethernet (SMSC9115 from SMSC9118 family) */
+#define CONFIG_NET_MULTI
+#define CONFIG_SMC911X
+#define CONFIG_SMC911X_32_BIT
+#define CONFIG_SMC911X_BASE		0x2C000000
+
+/* BOOTP fields */
+#define CONFIG_BOOTP_SUBNETMASK		0x00000001
+#define CONFIG_BOOTP_GATEWAY		0x00000002
+#define CONFIG_BOOTP_HOSTNAME		0x00000004
+#define CONFIG_BOOTP_BOOTPATH		0x00000010
+
+#endif /* CONFIG_CMD_NET */
+
+/* Support for relocation */
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR	0x4020f800
+#define CONFIG_SYS_INIT_RAM_SIZE	0x800
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
+					 CONFIG_SYS_INIT_RAM_SIZE - \
+					 GENERATED_GBL_DATA_SIZE)
+
+/* -----------------------------------------------------------------------------
+ * Board specific
+ * -----------------------------------------------------------------------------
+ */
+#define CONFIG_SYS_NO_FLASH
+
+/* Uncomment to define the board revision statically */
+/* #define CONFIG_STATIC_BOARD_REV	OMAP3EVM_BOARD_GEN_2 */
+
+#endif /* __OMAP3_EVM_COMMON_H */