Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm:
  Arm: re-introduce the MACH_TYPE_XXXXXX for EB_CPUX9K2 board
  arm: jadecpu: Readd MACH_TYPE_JADECPU
  at91: defined mach-types for otc570 board in board config file
  at91: defined mach-types for meesc board in board config file
  mx31pdk: Enable D and I caches
  ehci-mxc: remove incorrect comment
  README: Fix supported i.MX SoC list for CONFIG_MXC_SPI
  mx53: Turn off child clocks before reconfigure perclk_root
  qong: enable support for compressed images
  imx: imx31_phycore.h: fix checkpatch warnings
  vision2: Remove unused get_board_rev function
  mx53smd: Remove unused get_board_rev function
  mx53ard: Remove unused get_board_rev function
  mx53evk: Remove unused get_board_rev function
  mx53evk: Add RTC support
  mx53loco: Remove unused get_board_rev function
  mx53evk: Remove unneeded '1' from mx53evk.h
  OMAP3: mvblx: Initial support for mvBlueLYNX-X
  ARM: dig297: Define MACH_TYPE_OMAP3_CPS and CONFIG_MACH_TYPE
  omap3: mem: Move comments next to definitions
  omap3: mem: Clean-up whitespaces
  omap3: mem: Define and use common macros
  Davinci: ea20: added PREBOOT to configuration
  Davinci: ea20: added I2C support
  Davinci: ea20: added video support
  VIDEO: davinci: add framebuffer to da8xx
  ARM: Davinci: added missing registers to hardware.h
  Davinci: ea20: add gpios for LCD backlight control
  Davinci: ea20: add gpio for keeping power on in board_late_init
  Davinci: ea20: Add default U-Boot environment
  Davinci: ea20: Add early init to get early output from console
  Davinci: ea20: Add NAND support
  Davinci: ea20: set GPIOs to hold MII-Phy in reset and set UART0-Switch for console
  Davinci: ea20: set console on UART0
  arm, davinci: add cam_enc_4xx support
  arm926ejs, davinci: add missing spi defines for dm365
  arm926ejs, davinci: add cpuinfo for dm365
  arm, davinci: add lowlevel function for dm365 soc
  arm, davinci: add header files for dm365
  spl, nand: add 4bit HW ecc oob first nand_read_page function
  arm, davinci: add support for new spl framework
  spl: add option for adding post memory test to the SPL framework
  net, davinci_emac: make clock divider in MDIO control register configurable
  arm, usb, davinci: make USBPHY_CTL register configurable
  usb, davinci: add enable_vbus() weak function
  omap3evm: fix errors caused by multiple definitions
  omap3evm: Add (quick) configuration for NAND only
  omap3evm: Add (quick) configuration for MMC/SD only
  omap3evm: move common config options to new file
  omap3evm: Prepare to split configuration
  omap3evm: Reorder related config options
  omap/spl: actually enable the console
  davinci_emac: compilation fix, phy is array now
  omap3evm: Set environment variable 'ethaddr'
  arm, arm926: fix missing symbols in NAND_SPL mode
  arm, davinci: Add function lpsc_syncreset()
  arm, davinci: replace CONFIG_PRELOADER with CONFIG_SPL_BUILD
  arm/km: portl2 environment address update to P1B
  arm/km: adapt bootcounter evaluation
  arm/km: enable jffs2 cmds
  arm/km: trigger reconfiguration for the Xilinx FPGA
  arm/km: add boardid and hwkey to kernel command line
  ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boards
  netspace_v2: enable I2C EEPROM support
  netspace_v2: fix SDRAM configuration
  armada100: define CONFIG_SYS_CACHELINE_SIZE
  pantheon: define CONFIG_SYS_CACHELINE_SIZE
  kirkwood: define CONFIG_SYS_CACHELINE_SIZE
  kirkwood: drop empty asm-offsets.s file
  arm/km/mgcoge3un: enhance "waitforne" feature
  arm/km: add variable waitforne to mgcoge3un
  gplugD: Fix for error:MACH_TYPE_SHEEVAD undeclared
  ARM: dreamplug: fix compilation
  ARM: DockStar: fix compilation
  ARM: netspace_v2: fix warnings
  am335x: Drop board_sysinfo struct
  am335x: Temporarily add MACH_TYPE define
  misc:pmic:samsung Enable PMIC driver at C210 Universal target
  dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p UNIVERSAL C210 target
  dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p GONI target
  smdkv310: use macro for mmc data read function address
  smdkv310: use spl framework for mmc spl
  SMDKV310: use get_ram_size() to validate dram size
  SMDKV310: Initialize board id using CONFIG_MACH_TYPE
  ORIGEN : use absolute paths and fix tool naming
  ORIGEN : enable device tree support
  MX25: tx25: Fix building due to missing MACH_TYPE
  mx31: Add board support for HALE TT-01
  mx31: add ESD control registers
  mx31: define pins and init for UART2 and CSPI3
  MX35: add support for flea3 board
  MX51: vision2: add MACH_TYPE in config file
  vision2: Remove unused header file
  mx51evk: Remove unused get_board_rev function
  mx51evk: Remove unneeded '1' from mx51evk.h
  I2C: Fix mxc_i2c.c problem on imx31_phycore
  mx35pdk: Add RTC support
  mx51evk: Use GPIO API for configuring the IOMUX
  mx51evk: Add RTC support
  rtc: Make mc13783-rtc driver generic
  qong: remove unneeded IOMUX settings
  qong: Use mx31_set_gpr to setup USBH2 pins
  mx31: Introduce mx31_set_gpr function
  mx31pdk: Add MC13783 PMIC support
  qong: remove unneeded "1" from qong.h
  misc: pmic: fix regression in pmic_fsl.c (SPI)
  mx5 configs: CONFIG_PRIME should really be CONFIG_ETHPRIME
  MX35: Drop unnecessary prototypes from imx-regs.h
  I2C: added I2C-2 and I2C-3 to MX35
  MX35: factorize common assembly code
  MX35: add reset cause as provided by other i.MX
  MX35: add pins definition for UART3
  MX35: added ESDC structure to imx-regs

1 files changed, 254 insertions, 0 deletions

diff --git a/include/configs/tt01.h b/include/configs/tt01.h
new file mode 100644
index 0000000..6ef25cd
--- /dev/null
+++ b/include/configs/tt01.h
@@ -0,0 +1,254 @@
+/*
+ * (C) Copyright 2011 HALE electronic <helmut.raiger@hale.at>
+ * (C) Copyright 2008 Magnus Lilja <lilja.magnus@gmail.com>
+ *
+ * Configuration settings for the HALE TT-01 board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/imx-regs.h>
+
+/* High Level Configuration Options */
+#define CONFIG_ARM1136
+#define CONFIG_MX31
+#define CONFIG_MX31_HCLK_FREQ	26000000
+#define CONFIG_MX31_CLK32	32768
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+
+#define CONFIG_MACH_TYPE	3726		/* not yet in mach-types.h */
+#define CONFIG_SYS_TEXT_BASE	0xA0000000
+
+
+/*
+ * Physical Memory Map:
+ *   CS settings are defined by i.MX31:
+ *     - CSD0 and CDS1 are 256MB each, starting at 0x80000000 and 0x9000000
+ *     - CS0 and CS1 are 128MB each, at A0000000 and A8000000
+ *     - CS2 to CS5 are 32MB each, at B0.., B2.., B4.., B6..
+ *
+ * HALE set-up of the bluetechnix board for now is:
+ *   - 128MB DDR (2x64MB, 2x16bit), connected to 32bit DDR ram interface
+ *   - NOR-Flash (Spansion 32MB MCP, Flash+16MB PSRAM), 16bit interface at CS0
+ *		- S71WS256ND0BFWYM (and CS1 for 64MB S71WS512ND0 without PSRAM)
+ *        the flash chip is a mirrorbit S29WS256N !
+ *   - the PSRAM is hooked to CS5 (0xB6000000)
+ *   - Intel Strata Flash PF48F2000P0ZB00, 16bit interface at (CS0 or) CS1
+ *     - 64Mbit = 8MByte (will go away in the production set-up)
+ *   - NAND-Flash NAND01GR3B2BZA6 at NAND-FC:
+ *		1Gbit=128MB, 2048+64 bytes/page, 64pages x 1024 blocks
+ *   - Ethernet controller SMC9118 at CS4 via FPGA, 16bit interface
+ *
+ * u-boot will support the 32MB nor flash and the 128MB NAND flash, the PSRAM
+ * is not used right now. We should be able to reduce the SOM to NAND flash
+ * only and boot from there.
+ */
+#define CONFIG_NR_DRAM_BANKS	1
+#define PHYS_SDRAM_1		CSD0_BASE
+#define PHYS_SDRAM_1_SIZE	(128 * 1024 * 1024)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+#define CONFIG_SYS_GBL_DATA_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR	\
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)
+
+/* default load address, 1MB up the road */
+#define CONFIG_SYS_LOAD_ADDR		(PHYS_SDRAM_1+0x100000)
+
+/* The stack sizes are set up in start.S using the settings below */
+#define CONFIG_STACKSIZE	(128 * 1024)	/* regular stack */
+
+/* Size of malloc() pool, make sure possible frame buffer fits */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 10*1024*1024)
+
+/* memtest works on all but the last 1MB (u-boot) and malloc area  */
+#define CONFIG_SYS_MEMTEST_START	PHYS_SDRAM_1
+#define CONFIG_SYS_MEMTEST_END \
+	(PHYS_SDRAM_1+(PHYS_SDRAM_1_SIZE-CONFIG_SYS_MALLOC_LEN-0x100000))
+
+/* CFI FLASH driver setup */
+#define CONFIG_SYS_FLASH_CFI		/* Flash memory is CFI compliant */
+#define CONFIG_FLASH_CFI_DRIVER		/* Use drivers/cfi_flash.c */
+#define CONFIG_FLASH_SPANSION_S29WS_N
+/*
+ * TODO: Bluetechnix (the supplier of the SOM) did define these values
+ * in their original version of u-boot (1.2 or so). This should be
+ * reviewed.
+ *
+ * #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+ * #define CONFIG_SYS_FLASH_PROTECTION
+ */
+#define CONFIG_SYS_FLASH_BASE		CS0_BASE
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT (254+8) /* max number of sectors per chip */
+
+/*
+ * FLASH and environment organization, only the Spansion chip is supported:
+ * - it has 254 * 128kB + 8 * 32kB blocks
+ * - this setup uses 4*32k+3*128k as monitor space = 0xA000 0000 to 0xA00F FFFF
+ *		and 2 sectors with 128k as environment =
+ *		A010 0000 to 0xA011 FFFF and 0xA012 0000 to 0xA013 FFFF
+ * - this could be less, but this is only for developer versions of the board
+ *   and no-one is going to use the NOR flash anyway.
+ *
+ * Monitor is at the beginning of the NOR-Flash, 1MB reserved. Again this is
+ * way to large, but it avoids ENV overwrite (when updating u-boot) in case
+ * size breaks the next boundary (as it has with 128k).
+ */
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MONITOR_LEN		(1024 * 1024)
+
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE	(128 * 1024)
+#define CONFIG_ENV_SIZE		(8 * 1024) /* smaller for faster access */
+
+/* Address and size of Redundant Environment Sector	*/
+#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SIZE_REDUND		CONFIG_ENV_SIZE
+
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+
+/* Hardware drivers */
+
+/*
+ * on TT-01 UART1 pins are used by Audio, so we use UART2
+ * TT-01 implements a hardware that turns off components depending on
+ * the power level. In PL=1 the RS232 transceiver is usually off,
+ * make sure that the transceiver is enabled during PL=1 for testing!
+ */
+#define CONFIG_MXC_UART
+#define CONFIG_SYS_MX31_UART2
+
+#define CONFIG_MXC_SPI
+#define CONFIG_MXC_GPIO
+
+/* MC13783 connected to CSPI3 and SS0 */
+#define CONFIG_PMIC
+#define CONFIG_PMIC_SPI
+#define CONFIG_PMIC_FSL
+
+#define CONFIG_FSL_PMIC_BUS		2
+#define CONFIG_FSL_PMIC_CS		0
+#define CONFIG_FSL_PMIC_CLK		1000000
+#define CONFIG_FSL_PMIC_MODE	(SPI_MODE_0 | SPI_CS_HIGH)
+#define CONFIG_FSL_PMIC_BITLEN	32
+
+#define CONFIG_RTC_MC13XXX
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+/* console is UART2 on TT-01 */
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{9600, 19200, 38400, 57600, 115200}
+
+/* ethernet setup for the onboard smc9118 */
+#define CONFIG_MII
+#define CONFIG_SMC911X
+/* 16 bit, onboard ethernet, decoded via MACH-MX0 FPGA at 0x84200000 */
+#define CONFIG_SMC911X_BASE		(CS4_BASE+0x200000)
+#define CONFIG_SMC911X_16_BIT
+
+/*
+ * Command definition
+ */
+
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_NAND
+/*
+ * #define CONFIG_CMD_NAND_LOCK_UNLOCK the NAND01... chip does not support
+ * the NAND_CMD_LOCK_STATUS command, however the NFC of i.MX31 supports
+ * a software locking scheme.
+ */
+
+#define CONFIG_BOOTDELAY	3
+
+/*
+ * currently a default setting for booting via script is implemented
+ *   set user to login name and serverip to tftp host, define your
+ *   boot behaviour in bootscript.loginname
+ */
+#define	CONFIG_EXTRA_ENV_SETTINGS \
+	"bootcmd=dhcp bootscript.$(user); source\0"
+
+#define CONFIG_BOOTP_SERVERIP /* tftp serverip not overruled by dhcp server */
+#define CONFIG_BOOTP_SEND_HOSTNAME /* if env-var 'hostname' is set, send it */
+
+/* Miscellaneous configurable options */
+#define CONFIG_HUSH_PARSER
+#define CONFIG_PROMPT_HUSH_PS2	"> "
+
+#define CONFIG_SYS_LONGHELP			/* undef to save memory */
+#define CONFIG_SYS_PROMPT	"TT01> "
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE + \
+				sizeof(CONFIG_SYS_PROMPT)+16)
+/* max number of command args */
+#define CONFIG_SYS_MAXARGS	16
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_HZ			1000
+
+#define CONFIG_CMDLINE_EDITING
+
+#define CONFIG_NAND_MXC
+#define CONFIG_SYS_MAX_NAND_DEVICE		1
+#define CONFIG_SYS_NAND_MAX_CHIPS		1
+
+/*
+ * actually this is nothing someone wants to configure!
+ * CONFIG_SYS_NAND_BASE despite being passed to board_nand_init()
+ * is not used by the driver.
+ */
+#define CONFIG_MXC_NAND_REGS_BASE	NFC_BASE_ADDR
+#define CONFIG_SYS_NAND_BASE		NFC_BASE_ADDR
+#define CONFIG_MXC_NAND_HWECC
+
+/* the current u-boot driver does not use the nand flash setup! */
+#define CONFIG_SYS_NAND_LARGEPAGE
+/*
+ * it's not 16 bit:
+ * #define CONFIG_SYS_NAND_BUSWIDTH_16BIT
+ *    the current u-boot mxc_nand.c tries to auto-detect, but this only
+ *    reads the boot settings during reset (which might be wrong)
+ */
+
+#endif /* __CONFIG_H */