diff options
| -rw-r--r-- | arch/arm/dts/Makefile | 1 | ||||
| -rw-r--r-- | arch/arm/dts/rk3288-phycore-rdk.dts | 294 | ||||
| -rw-r--r-- | arch/arm/dts/rk3288-phycore-som.dtsi | 506 | ||||
| -rw-r--r-- | arch/arm/mach-rockchip/rk3288-board-spl.c | 40 | ||||
| -rw-r--r-- | arch/arm/mach-rockchip/rk3288/Kconfig | 10 | ||||
| -rw-r--r-- | board/phytec/phycore_rk3288/Kconfig | 15 | ||||
| -rw-r--r-- | board/phytec/phycore_rk3288/MAINTAINERS | 6 | ||||
| -rw-r--r-- | board/phytec/phycore_rk3288/Makefile | 8 | ||||
| -rw-r--r-- | board/phytec/phycore_rk3288/phycore-rk3288.c | 8 | ||||
| -rw-r--r-- | configs/phycore-rk3288_defconfig | 70 | ||||
| -rw-r--r-- | include/configs/phycore_rk3288.h | 23 |
11 files changed, 981 insertions, 0 deletions
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 9cc5c1e..fd28290 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -34,6 +34,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \ rk3288-fennec.dtb \ rk3288-firefly.dtb \ rk3288-miqi.dtb \ + rk3288-phycore-rdk.dtb \ rk3288-popmetal.dtb \ rk3288-rock2-square.dtb \ rk3288-tinker.dtb \ diff --git a/arch/arm/dts/rk3288-phycore-rdk.dts b/arch/arm/dts/rk3288-phycore-rdk.dts new file mode 100644 index 0000000..f2bb7b5 --- /dev/null +++ b/arch/arm/dts/rk3288-phycore-rdk.dts @@ -0,0 +1,294 @@ +/* + * Device tree file for Phytec PCM-947 carrier board + * Copyright (C) 2017 PHYTEC Messtechnik GmbH + * Author: Wadim Egorov <w.egorov@phytec.de> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include <dt-bindings/input/input.h> +#include "rk3288-phycore-som.dtsi" + +/ { + model = "Phytec RK3288 PCM-947"; + compatible = "phytec,rk3288-pcm-947", "phytec,rk3288-phycore-som", "rockchip,rk3288"; + + chosen { + stdout-path = &uart2; + }; + + config { + u-boot,dm-pre-reloc; + u-boot,boot0 = &emmc; + }; + + user_buttons: user-buttons { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&user_button_pins>; + + button@0 { + label = "home"; + linux,code = <KEY_HOME>; + gpios = <&gpio8 0 GPIO_ACTIVE_HIGH>; + wakeup-source; + }; + + button@1 { + label = "menu"; + linux,code = <KEY_MENU>; + gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>; + wakeup-source; + }; + }; + + vcc_host0_5v: usb-host0-regulator { + compatible = "regulator-fixed"; + gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&host0_vbus_drv>; + regulator-name = "vcc_host0_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + vin-supply = <&vdd_in_otg_out>; + }; + + vcc_host1_5v: usb-host1-regulator { + compatible = "regulator-fixed"; + gpio = <&gpio2 0 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&host1_vbus_drv>; + regulator-name = "vcc_host1_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + vin-supply = <&vdd_in_otg_out>; + }; + + vcc_otg_5v: usb-otg-regulator { + compatible = "regulator-fixed"; + gpio = <&gpio2 12 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&otg_vbus_drv>; + regulator-name = "vcc_otg_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + vin-supply = <&vdd_in_otg_out>; + }; +}; + +&dmc { + rockchip,num-channels = <2>; + rockchip,pctl-timing = <0x29a 0xc8 0x1f8 0x42 0x4e 0x4 0xea 0xa + 0x5 0x0 0xa 0x7 0x19 0x24 0xa 0x7 + 0x5 0xa 0x5 0x200 0x5 0x10 0x40 0x0 + 0x1 0x7 0x7 0x4 0xc 0x43 0x100 0x0 + 0x5 0x0>; + rockchip,phy-timing = <0x48f9aab4 0xea0910 0x1002c200 + 0xa60 0x40 0x10 0x0>; + rockchip,sdram-channel = /bits/ 8 <0x1 0xa 0x3 0x2 0x1 0x0 0xe 0xe>; + rockchip,sdram-params = <0x30B25564 0x627 3 666000000 3 5 1>; +}; + +&gmac { + status = "okay"; +}; + +&hdmi { + status = "okay"; +}; + +&i2c1 { + status = "okay"; + + touchscreen@44 { + compatible = "st,stmpe811"; + reg = <0x44>; + }; + + adc@64 { + compatible = "maxim,max1037"; + reg = <0x64>; + }; + + i2c_rtc: rtc@68 { + compatible = "rv4162"; + reg = <0x68>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c_rtc_int>; + interrupt-parent = <&gpio5>; + interrupts = <10 0>; + }; +}; + +&i2c3 { + status = "okay"; + + i2c_eeprom_cb: eeprom@51 { + compatible = "atmel,24c32"; + reg = <0x51>; + pagesize = <32>; + }; +}; + +&i2c4 { + status = "okay"; +}; + +&i2c5 { + status = "okay"; +}; + +&pinctrl { + u-boot,dm-pre-reloc; + + pcfg_pull_up_drv_12ma: pcfg-pull-up-drv-12ma { + bias-pull-up; + drive-strength = <12>; + }; + + buttons { + user_button_pins: user-button-pins { + /* button 1 */ + rockchip,pins = <8 3 RK_FUNC_GPIO &pcfg_pull_up>, + /* button 2 */ + <8 0 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + rv4162 { + i2c_rtc_int: i2c-rtc-int { + rockchip,pins = <5 10 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + sdmmc { + /* + * Default drive strength isn't enough to achieve even + * high-speed mode on pcm-947 board so bump up to 12 mA. + */ + sdmmc_bus4: sdmmc-bus4 { + rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_12ma>, + <6 17 RK_FUNC_1 &pcfg_pull_up_drv_12ma>, + <6 18 RK_FUNC_1 &pcfg_pull_up_drv_12ma>, + <6 19 RK_FUNC_1 &pcfg_pull_up_drv_12ma>; + }; + + sdmmc_clk: sdmmc-clk { + rockchip,pins = <6 20 RK_FUNC_1 &pcfg_pull_none_12ma>; + }; + + sdmmc_cmd: sdmmc-cmd { + rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_12ma>; + }; + + sdmmc_pwr: sdmmc-pwr { + rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + touchscreen { + ts_irq_pin: ts-irq-pin { + rockchip,pins = <5 15 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + usb_host { + host0_vbus_drv: host0-vbus-drv { + rockchip,pins = <2 13 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + host1_vbus_drv: host1-vbus-drv { + rockchip,pins = <2 0 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + usb_otg { + otg_vbus_drv: otg-vbus-drv { + rockchip,pins = <2 12 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; + +&sdmmc { + u-boot,dm-pre-reloc; + + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + card-detect-delay = <200>; + disable-wp; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>; + vmmc-supply = <&vdd_io_sd>; + vqmmc-supply = <&vdd_io_sd>; + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>; + status = "okay"; +}; + +&uart2 { + u-boot,dm-pre-reloc; + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; + +&usb_host0_ehci { + status = "okay"; +}; + +&usb_host1 { + status = "okay"; +}; + +&usb_otg { + status = "okay"; +}; diff --git a/arch/arm/dts/rk3288-phycore-som.dtsi b/arch/arm/dts/rk3288-phycore-som.dtsi new file mode 100644 index 0000000..fd463f4 --- /dev/null +++ b/arch/arm/dts/rk3288-phycore-som.dtsi @@ -0,0 +1,506 @@ +/* + * Device tree file for Phytec phyCORE-RK3288 SoM + * Copyright (C) 2017 PHYTEC Messtechnik GmbH + * Author: Wadim Egorov <w.egorov@phytec.de> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/net/ti-dp83867.h> +#include "rk3288.dtsi" + +/ { + model = "Phytec RK3288 phyCORE"; + compatible = "phytec,rk3288-phycore-som", "rockchip,rk3288"; + + /* + * Set the minimum memory size here and + * let the bootloader set the real size. + */ + memory { + device_type = "memory"; + reg = <0 0x8000000>; + }; + + aliases { + rtc0 = &i2c_rtc; + rtc1 = &rk818; + }; + + ext_gmac: external-gmac-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <125000000>; + clock-output-names = "ext_gmac"; + }; + + io_domains: io_domains { + compatible = "rockchip,rk3288-io-voltage-domain"; + + status = "okay"; + sdcard-supply = <&vdd_io_sd>; + flash0-supply = <&vdd_emmc_io>; + flash1-supply = <&vdd_misc_1v8>; + gpio1830-supply = <&vdd_3v3_io>; + gpio30-supply = <&vdd_3v3_io>; + bb-supply = <&vdd_3v3_io>; + dvp-supply = <&vdd_3v3_io>; + lcdc-supply = <&vdd_3v3_io>; + wifi-supply = <&vdd_3v3_io>; + audio-supply = <&vdd_3v3_io>; + }; + + leds: user-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&user_led>; + + user { + label = "green_led"; + gpios = <&gpio7 2 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "keep"; + }; + }; + + vdd_emmc_io: vdd-emmc-io { + compatible = "regulator-fixed"; + regulator-name = "vdd_emmc_io"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vdd_3v3_io>; + }; + + vdd_in_otg_out: vdd-in-otg-out { + compatible = "regulator-fixed"; + regulator-name = "vdd_in_otg_out"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + vdd_misc_1v8: vdd-misc-1v8 { + compatible = "regulator-fixed"; + regulator-name = "vdd_misc_1v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; +}; + +&cpu0 { + cpu0-supply = <&vdd_cpu>; + operating-points = < + /* KHz uV */ + 1800000 1400000 + 1608000 1350000 + 1512000 1300000 + 1416000 1200000 + 1200000 1100000 + 1008000 1050000 + 816000 1000000 + 696000 950000 + 600000 900000 + 408000 900000 + 312000 900000 + 216000 900000 + 126000 900000 + >; +}; + +&emmc { + status = "okay"; + u-boot,dm-pre-reloc; + + bus-width = <8>; + cap-mmc-highspeed; + disable-wp; + non-removable; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>; + vmmc-supply = <&vdd_3v3_io>; + vqmmc-supply = <&vdd_emmc_io>; +}; + +&gmac { + assigned-clocks = <&cru SCLK_MAC>; + assigned-clock-parents = <&ext_gmac>; + clock_in_out = "input"; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins &phy_rst &phy_int>; + phy-handle = <&phy0>; + phy-supply = <&vdd_eth_2v5>; + phy-mode = "rgmii-id"; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 1000000>; + snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>; + tx_delay = <0x0>; + rx_delay = <0x0>; + + mdio0 { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + interrupt-parent = <&gpio4>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + enet-phy-lane-no-swap; + }; + }; +}; + +&hdmi { + ddc-i2c-bus = <&i2c5>; +}; + +&i2c0 { + status = "okay"; + u-boot,dm-pre-reloc; + + clock-frequency = <400000>; + + rk818: pmic@1c { + status = "okay"; + compatible = "rockchip,rk818"; + reg = <0x1c>; + interrupt-parent = <&gpio0>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int>; + rockchip,system-power-controller; + wakeup-source; + #clock-cells = <1>; + u-boot,dm-pre-reloc; + + vcc1-supply = <&vdd_sys>; + vcc2-supply = <&vdd_sys>; + vcc3-supply = <&vdd_sys>; + vcc4-supply = <&vdd_sys>; + boost-supply = <&vdd_in_otg_out>; + vcc6-supply = <&vdd_sys>; + vcc7-supply = <&vdd_misc_1v8>; + vcc8-supply = <&vdd_misc_1v8>; + vcc9-supply = <&vdd_3v3_io>; + vddio-supply = <&vdd_3v3_io>; + + regulators { + u-boot,dm-pre-reloc; + vdd_log: DCDC_REG1 { + regulator-name = "vdd_log"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_gpu: DCDC_REG2 { + regulator-name = "vdd_gpu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1250000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-name = "vcc_ddr"; + regulator-always-on; + regulator-boot-on; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vdd_3v3_io: DCDC_REG4 { + regulator-name = "vdd_3v3_io"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vdd_sys: DCDC_BOOST { + regulator-name = "vdd_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <5000000>; + }; + }; + + /* vcc9 */ + vdd_sd: SWITCH_REG { + regulator-name = "vdd_sd"; + regulator-always-on; + regulator-boot-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + /* vcc6 */ + vdd_eth_2v5: LDO_REG2 { + regulator-name = "vdd_eth_2v5"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <2500000>; + }; + }; + + /* vcc7 */ + vdd_1v0: LDO_REG3 { + regulator-name = "vdd_1v0"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + + /* vcc8 */ + vdd_1v8_lcd_ldo: LDO_REG4 { + regulator-name = "vdd_1v8_lcd_ldo"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + /* vcc8 */ + vdd_1v0_lcd: LDO_REG6 { + regulator-name = "vdd_1v0_lcd"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + + /* vcc7 */ + vdd_1v8_ldo: LDO_REG7 { + regulator-name = "vdd_1v8_ldo"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-state-mem { + regulator-off-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + /* vcc9 */ + vdd_io_sd: LDO_REG9 { + regulator-name = "vdd_io_sd"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + }; + }; + + /* M24C32-D */ + i2c_eeprom: eeprom@50 { + compatible = "atmel,24c32"; + reg = <0x50>; + pagesize = <32>; + }; + + vdd_cpu: regulator@60 { + compatible = "fcs,fan53555"; + reg = <0x60>; + fcs,suspend-voltage-selector = <1>; + regulator-always-on; + regulator-boot-on; + regulator-enable-ramp-delay = <300>; + regulator-name = "vdd_cpu"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1430000>; + regulator-ramp-delay = <8000>; + vin-supply = <&vdd_sys>; + }; +}; + +&pinctrl { + pcfg_output_high: pcfg-output-high { + output-high; + }; + + emmc { + /* + * We run eMMC at max speed; bump up drive strength. + * We also have external pulls, so disable the internal ones. + */ + emmc_clk: emmc-clk { + rockchip,pins = <3 18 RK_FUNC_2 &pcfg_pull_none_12ma>; + }; + + emmc_cmd: emmc-cmd { + rockchip,pins = <3 16 RK_FUNC_2 &pcfg_pull_none_12ma>; + }; + + emmc_bus8: emmc-bus8 { + rockchip,pins = <3 0 RK_FUNC_2 &pcfg_pull_none_12ma>, + <3 1 RK_FUNC_2 &pcfg_pull_none_12ma>, + <3 2 RK_FUNC_2 &pcfg_pull_none_12ma>, + <3 3 RK_FUNC_2 &pcfg_pull_none_12ma>, + <3 4 RK_FUNC_2 &pcfg_pull_none_12ma>, + <3 5 RK_FUNC_2 &pcfg_pull_none_12ma>, + <3 6 RK_FUNC_2 &pcfg_pull_none_12ma>, + <3 7 RK_FUNC_2 &pcfg_pull_none_12ma>; + }; + }; + + gmac { + phy_int: phy-int { + rockchip,pins = <4 2 RK_FUNC_GPIO &pcfg_pull_up>; + }; + + phy_rst: phy-rst { + rockchip,pins = <4 8 RK_FUNC_GPIO &pcfg_output_high>; + }; + }; + + leds { + user_led: user-led { + rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_output_high>; + }; + }; + + pmic { + pmic_int: pmic-int { + rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>; + }; + + /* Pin for switching state between sleep and non-sleep state */ + pmic_sleep: pmic-sleep { + rockchip,pins = <RK_GPIO0 0 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; +}; + +&pwm1 { + status = "okay"; +}; + +&saradc { + status = "okay"; + vref-supply = <&vdd_1v8_ldo>; +}; + +&spi2 { + status = "okay"; + + serial_flash: flash@0 { + compatible = "micron,n25q128a13", "jedec,spi-nor"; + reg = <0x0>; + spi-max-frequency = <50000000>; + m25p,fast-read; + #address-cells = <1>; + #size-cells = <1>; + status = "okay"; + }; +}; + +&tsadc { + status = "okay"; + rockchip,hw-tshut-mode = <0>; + rockchip,hw-tshut-polarity = <0>; +}; + +&vopb { + status = "okay"; +}; + +&vopb_mmu { + status = "okay"; +}; + +&vopl { + status = "okay"; +}; + +&vopl_mmu { + status = "okay"; +}; + +&wdt { + status = "okay"; +}; diff --git a/arch/arm/mach-rockchip/rk3288-board-spl.c b/arch/arm/mach-rockchip/rk3288-board-spl.c index 8ca6b1e..5668fd2 100644 --- a/arch/arm/mach-rockchip/rk3288-board-spl.c +++ b/arch/arm/mach-rockchip/rk3288-board-spl.c @@ -8,6 +8,7 @@ #include <debug_uart.h> #include <dm.h> #include <fdtdec.h> +#include <i2c.h> #include <led.h> #include <malloc.h> #include <ram.h> @@ -25,6 +26,7 @@ #include <dm/test.h> #include <dm/util.h> #include <power/regulator.h> +#include <power/rk8xx_pmic.h> DECLARE_GLOBAL_DATA_PTR; @@ -157,6 +159,32 @@ static int configure_emmc(struct udevice *pinctrl) } #endif +#if !defined(CONFIG_SPL_OF_PLATDATA) +static int phycore_init(void) +{ + struct udevice *pmic; + int ret; + + ret = uclass_first_device_err(UCLASS_PMIC, &pmic); + if (ret) + return ret; + +#if defined(CONFIG_SPL_POWER_SUPPORT) + /* Increase USB input current to 2A */ + ret = rk818_spl_configure_usb_input_current(pmic, 2000); + if (ret) + return ret; + + /* Close charger when USB lower then 3.26V */ + ret = rk818_spl_configure_usb_chrg_shutdown(pmic, 3260000); + if (ret) + return ret; +#endif + + return 0; +} +#endif + void board_init_f(ulong dummy) { struct udevice *pinctrl; @@ -203,6 +231,18 @@ void board_init_f(ulong dummy) debug("Pinctrl init failed: %d\n", ret); return; } + +#if !defined(CONFIG_SPL_OF_PLATDATA) + if (of_machine_is_compatible("phytec,rk3288-phycore-som")) { + ret = phycore_init(); + if (ret) { + debug("Failed to set up phycore power settings: %d\n", + ret); + return; + } + } +#endif + debug("\nspl:init dram\n"); ret = uclass_get_device(UCLASS_RAM, 0, &dev); if (ret) { diff --git a/arch/arm/mach-rockchip/rk3288/Kconfig b/arch/arm/mach-rockchip/rk3288/Kconfig index 8e7355e..53cc9a0 100644 --- a/arch/arm/mach-rockchip/rk3288/Kconfig +++ b/arch/arm/mach-rockchip/rk3288/Kconfig @@ -66,6 +66,14 @@ config TARGET_MIQI_RK3288 has 1 or 2 GiB SDRAM. Expansion connectors provide access to I2C, SPI, UART, GPIOs and fan control. +config TARGET_PHYCORE_RK3288 + bool "phyCORE-RK3288" + select BOARD_LATE_INIT + help + Add basic support for the PCM-947 carrier board, a RK3288 based + development board made by PHYTEC. This board works in a combination + with the phyCORE-RK3288 System on Module. + config TARGET_POPMETAL_RK3288 bool "PopMetal-RK3288" select BOARD_LATE_INIT @@ -129,6 +137,8 @@ source "board/google/veyron/Kconfig" source "board/mqmaker/miqi_rk3288/Kconfig" +source "board/phytec/phycore_rk3288/Kconfig" + source "board/radxa/rock2/Kconfig" source "board/rockchip/evb_rk3288/Kconfig" diff --git a/board/phytec/phycore_rk3288/Kconfig b/board/phytec/phycore_rk3288/Kconfig new file mode 100644 index 0000000..57cd8e2 --- /dev/null +++ b/board/phytec/phycore_rk3288/Kconfig @@ -0,0 +1,15 @@ +if TARGET_PHYCORE_RK3288 + +config SYS_BOARD + default "phycore_rk3288" + +config SYS_VENDOR + default "phytec" + +config SYS_CONFIG_NAME + default "phycore_rk3288" + +config BOARD_SPECIFIC_OPTIONS # dummy + def_bool y + +endif diff --git a/board/phytec/phycore_rk3288/MAINTAINERS b/board/phytec/phycore_rk3288/MAINTAINERS new file mode 100644 index 0000000..9c0de3c --- /dev/null +++ b/board/phytec/phycore_rk3288/MAINTAINERS @@ -0,0 +1,6 @@ +phyCORE-RK3288 +M: Wadim Egorov <w.egorov@phytec.de> +S: Maintained +F: board/phytec/phycore_rk3288 +F: include/configs/phycore_rk3288.h +F: configs/phycore-rk3288_defconfig diff --git a/board/phytec/phycore_rk3288/Makefile b/board/phytec/phycore_rk3288/Makefile new file mode 100644 index 0000000..f379fbe --- /dev/null +++ b/board/phytec/phycore_rk3288/Makefile @@ -0,0 +1,8 @@ +# +# Copyright (C) 2017 PHYTEC Messtechnik GmbH +# Author: Wadim Egorov <w.egorov@phytec.de> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += phycore-rk3288.o diff --git a/board/phytec/phycore_rk3288/phycore-rk3288.c b/board/phytec/phycore_rk3288/phycore-rk3288.c new file mode 100644 index 0000000..20696f6 --- /dev/null +++ b/board/phytec/phycore_rk3288/phycore-rk3288.c @@ -0,0 +1,8 @@ +/* + * Copyright (C) 2017 PHYTEC Messtechnik GmbH + * Author: Wadim Egorov <w.egorov@phytec.de> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> diff --git a/configs/phycore-rk3288_defconfig b/configs/phycore-rk3288_defconfig new file mode 100644 index 0000000..823db06 --- /dev/null +++ b/configs/phycore-rk3288_defconfig @@ -0,0 +1,70 @@ +CONFIG_ARM=y +CONFIG_ARCH_ROCKCHIP=y +CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_ROCKCHIP_RK3288=y +CONFIG_ROCKCHIP_SPL_BACK_TO_BROM=y +CONFIG_TARGET_PHYCORE_RK3288=y +CONFIG_SPL_STACK_R_ADDR=0x80000 +CONFIG_DEFAULT_DEVICE_TREE="rk3288-phycore-rdk" +CONFIG_DEBUG_UART=y +CONFIG_SILENT_CONSOLE=y +CONFIG_CONSOLE_MUX=y +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_SPL_STACK_R=y +CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x2000 +CONFIG_SPL_I2C_SUPPORT=y +CONFIG_SPL_POWER_SUPPORT=y +# CONFIG_CMD_IMLS is not set +CONFIG_CMD_GPT=y +CONFIG_CMD_MMC=y +CONFIG_CMD_SF=y +CONFIG_CMD_SPI=y +CONFIG_CMD_I2C=y +CONFIG_CMD_USB=y +CONFIG_CMD_GPIO=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_CACHE=y +CONFIG_CMD_TIME=y +CONFIG_CMD_PMIC=y +CONFIG_CMD_REGULATOR=y +# CONFIG_SPL_DOS_PARTITION is not set +# CONFIG_SPL_ISO_PARTITION is not set +# CONFIG_SPL_EFI_PARTITION is not set +CONFIG_SPL_PARTITION_UUIDS=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents" +CONFIG_REGMAP=y +CONFIG_SPL_REGMAP=y +CONFIG_SYSCON=y +CONFIG_SPL_SYSCON=y +# CONFIG_SPL_SIMPLE_BUS is not set +CONFIG_CLK=y +CONFIG_SPL_CLK=y +CONFIG_ROCKCHIP_GPIO=y +CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_ROCKCHIP=y +CONFIG_DM_ETH=y +CONFIG_ETH_DESIGNWARE=y +CONFIG_GMAC_ROCKCHIP=y +CONFIG_PINCTRL=y +CONFIG_SPL_PINCTRL=y +# CONFIG_SPL_PINCTRL_FULL is not set +CONFIG_PINCTRL_ROCKCHIP_RK3288=y +CONFIG_DM_PMIC=y +CONFIG_PMIC_RK8XX=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_REGULATOR_RK8XX=y +CONFIG_PWM_ROCKCHIP=y +CONFIG_RAM=y +CONFIG_SPL_RAM=y +CONFIG_DEBUG_UART_BASE=0xff690000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYS_NS16550=y +CONFIG_SYSRESET=y +CONFIG_USB=y +CONFIG_USB_STORAGE=y +CONFIG_USE_TINY_PRINTF=y +CONFIG_CMD_DHRYSTONE=y +CONFIG_ERRNO_STR=y diff --git a/include/configs/phycore_rk3288.h b/include/configs/phycore_rk3288.h new file mode 100644 index 0000000..aab43ed --- /dev/null +++ b/include/configs/phycore_rk3288.h @@ -0,0 +1,23 @@ +/* + * Copyright (C) 2017 PHYTEC Messtechnik GmbH + * Author: Wadim Egorov <w.egorov@phytec.de> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define ROCKCHIP_DEVICE_SETTINGS +#include <configs/rk3288_common.h> + +#undef BOOT_TARGET_DEVICES + +#define BOOT_TARGET_DEVICES(func) \ + func(MMC, mmc, 0) \ + func(MMC, mmc, 1) + +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 1 + +#endif |