diff options
Diffstat (limited to 'board/matrix_vision')
| -rw-r--r-- | board/matrix_vision/mergerbox/README | 59 | ||||
| -rw-r--r-- | board/matrix_vision/mvbc_p/README.mvbc_p | 73 | ||||
| -rw-r--r-- | board/matrix_vision/mvblm7/README.mvblm7 | 84 | ||||
| -rw-r--r-- | board/matrix_vision/mvsmr/README.mvsmr | 55 |
4 files changed, 271 insertions, 0 deletions
diff --git a/board/matrix_vision/mergerbox/README b/board/matrix_vision/mergerbox/README new file mode 100644 index 0000000..1994b65 --- /dev/null +++ b/board/matrix_vision/mergerbox/README @@ -0,0 +1,59 @@ +Matrix Vision MergerBox +----------------------- + +1. Board Description + + The MergerBox is a 120x160mm single board computing platform + for 3D Full-HD digital video processing. + + Power Supply is 10-32VDC. + +2 System Components + +2.1 CPU + Freescale MPC8377 CPU running at 800MHz core and 333MHz csb. + 256 MByte DDR-II memory @ 333MHz data rate. + 64 MByte Nor Flash on local bus. + 1 GByte Nand Flash on FCM. + 1 Vitesse VSC8601 RGMII ethernet Phys. + 1 USB host controller over ULPI I/F with 4-Port hub. + 2 serial ports. Console running on ttyS0 @ 115200 8N1. + 1 mPCIe expansion slot (PCIe x1 + USB) used for Wifi/Bt. + 2 PCIe x1 busses on local mPCIe and cutom expansion connector. + 2 SATA host ports. + System configuration (HRCW) is taken from I2C EEPROM. + +2.2 Graphics + SM107 emebedded video controller driving a 5" 800x480 TFT panel. + Connected over 32-Bit/66MHz PCI utilizing 4 MByte embedded memory. + +2.3 FPGA + Altera Cyclone-IV EP4C115 with several PCI DMA engines. + Connects to 7x Gennum 3G-SDI transceivers as video interconnect + as well as a HDMI v1.4 compliant output for 3D monitoring. + Utilizes two more DDR-II controllers providing 256MB memory. + +2.4 I2C + Bus1: + AD7418 @ 0x50 for voltage/temp. monitoring. + SX8650 @ 0x90 touch controller for HMI. + EEPROM @ 0xA0 for system setup (HRCW etc.) + vendor specifics. + Bus2: + mPCIe SMBus + SiI9022A @ 0x72/0xC0 HDMI transmitter. + TCA6416A @ 0x40 + 0x42 16-Bit I/O expander. + LMH1983 @ 0xCA video PLL. + DS1338C @ 0xD0 real-time clock with embedded crystal. + 9FG104 @ 0xDC 4x 100MHz LVDS SerDes reference clock. + +3 Flash layout. + + reset vector is 0x00000100, i.e. low boot. + + 00000000 u-boot binary. + 00100000 FPGA raw bit file. + 00300000 FIT image holding kernel, dtb and rescue squashfs. + 03d00000 u-boot environment. + 03e00000 splash image + + mtd partitions are propagated to linux kernel via device tree blob. diff --git a/board/matrix_vision/mvbc_p/README.mvbc_p b/board/matrix_vision/mvbc_p/README.mvbc_p new file mode 100644 index 0000000..a691137 --- /dev/null +++ b/board/matrix_vision/mvbc_p/README.mvbc_p @@ -0,0 +1,73 @@ +Matrix Vision mvBlueCOUGAR-P (mvBC-P) +------------------------------------- + +1. Board Description + + The mvBC-P is a 70x40x40mm multi board gigabit ethernet network camera + with main focus on GigEVision protocol in combination with local image + preprocessing. + + Power Supply is either VDC 48V or Pover over Ethernet (PoE). + +2 System Components + +2.1 CPU + Freescale MPC5200B CPU running at 400MHz core and 133MHz XLB/IPB. + 64MB SDRAM @ 133MHz. + 8 MByte Nor Flash on local bus. + 1 serial ports. Console running on ttyS0 @ 115200 8N1. + +2.2 PCI + PCI clock fixed at 66MHz. Arbitration inside FPGA. + Intel GD82541ER network MAC/PHY and FPGA connected. + +2.3 FPGA + Altera Cyclone-II EP2C8 with PCI DMA engine. + Connects to Matrix Vision specific CCD/CMOS sensor interface. + Utilizes 64MB Nand Flash. + +2.3.1 I/O @ FPGA + 2 Outputs : photo coupler + 2 Inputs : photo coupler + +2.4 I2C + LM75 @ 0x90 for temperature monitoring. + EEPROM @ 0xA0 for vendor specifics. + image sensor interface (slave addresses depend on sensor) + +3 Flash layout. + + reset vector is 0x00000100, i.e. "LOWBOOT". + + FF800000 u-boot + FF840000 u-boot script image + FF850000 redundant u-boot script image + FF860000 FPGA raw bit file + FF8A0000 tbd. + FF900000 root FS + FFC00000 kernel + FFFC0000 device tree blob + FFFD0000 redundant device tree blob + FFFE0000 environment + FFFF0000 redundant environment + + mtd partitions are propagated to linux kernel via device tree blob. + +4 Booting + + On startup the bootscript @ FF840000 is executed. This script can be + exchanged easily. Default boot mode is "boot from flash", i.e. system + works stand-alone. + + This behaviour depends on some environment variables : + + "netboot" : yes ->try dhcp/bootp and boot from network. + A "dhcp_client_id" and "dhcp_vendor-class-identifier" can be used for + DHCP server configuration, e.g. to provide different images to + different devices. + + During netboot the system tries to get 3 image files: + 1. Kernel - name + data is given during BOOTP. + 2. Initrd - name is stored in "initrd_name" + 3. device tree blob - name is stored in "dtb_name" + Fallback files are the flash versions. diff --git a/board/matrix_vision/mvblm7/README.mvblm7 b/board/matrix_vision/mvblm7/README.mvblm7 new file mode 100644 index 0000000..a0686f7 --- /dev/null +++ b/board/matrix_vision/mvblm7/README.mvblm7 @@ -0,0 +1,84 @@ +Matrix Vision mvBlueLYNX-M7 (mvBL-M7) +------------------------------------- + +1. Board Description + + The mvBL-M7 is a 120x120mm single board computing platform + with strong focus on stereo image processing applications. + + Power Supply is either VDC 12-48V or Pover over Ethernet (PoE) + on any port (requires add-on board). + +2 System Components + +2.1 CPU + Freescale MPC8343VRAGDB CPU running at 400MHz core and 266MHz csb. + 512MByte DDR-II memory @ 133MHz. + 8 MByte Nor Flash on local bus. + 2 Vitesse VSC8601 RGMII ethernet Phys. + 1 USB host controller over ULPI I/F. + 2 serial ports. Console running on ttyS0 @ 115200 8N1. + 1 SD-Card slot connected to SPI. + System configuration (HRCW) is taken from I2C EEPROM. + +2.2 PCI + A miniPCI Type-III socket is present. PCI clock fixed at 66MHz. + +2.3 FPGA + Altera Cyclone-II EP2C20/35 with PCI DMA engines. + Connects to dual Matrix Vision specific CCD/CMOS sensor interfaces. + Utilizes another 256MB DDR-II memory and 32-128MB Nand Flash. + +2.3.1 I/O @ FPGA + 2x8 Outputs : Infineon High-Side Switches to Main Supply. + 2x8 Inputs : Programmable input threshold + trigger capabilities + 2 dedicated flash interfaces for illuminator boards. + Cross trigger for chaining several boards. + +2.4 I2C + Bus1: + MAX5381 DAC @ 0x60 for 1st digital input threshold. + LM75 @ 0x90 for temperature monitoring. + EEPROM @ 0xA0 for system setup (HRCW etc.) + vendor specifics. + 1st image sensor interface (slave addresses depend on sensor) + Bus2: + MAX5381 DAC @ 0x60 for 2nd digital input threshold. + 2nd image sensor interface (slave addresses depend on sensor) + +3 Flash layout. + + reset vector is 0xFFF00100, i.e. "HIGHBOOT". + + FF800000 environment + FF802000 redundant environment + FF804000 u-boot script image + FF806000 redundant u-boot script image + FF808000 device tree blob + FF80A000 redundant device tree blob + FF80C000 tbd. + FF80E000 tbd. + FF810000 kernel + FFC00000 root FS + FFF00000 u-boot + FFF80000 FPGA raw bit file + + mtd partitions are propagated to linux kernel via device tree blob. + +4 Booting + + On startup the bootscript @ FF804000 is executed. This script can be + exchanged easily. Default boot mode is "boot from flash", i.e. system + works stand-alone. + + This behaviour depends on some environment variables : + + "netboot" : yes ->try dhcp/bootp and boot from network. + A "dhcp_client_id" and "dhcp_vendor-class-identifier" can be used for + DHCP server configuration, e.g. to provide different images to + different devices. + + During netboot the system tries to get 3 image files: + 1. Kernel - name + data is given during BOOTP. + 2. Initrd - name is stored in "initrd_name" + 3. device tree blob - name is stored in "dtb_name" + Fallback files are the flash versions. diff --git a/board/matrix_vision/mvsmr/README.mvsmr b/board/matrix_vision/mvsmr/README.mvsmr new file mode 100644 index 0000000..8e34cb7 --- /dev/null +++ b/board/matrix_vision/mvsmr/README.mvsmr @@ -0,0 +1,55 @@ +Matrix Vision mvSMR +------------------- + +1. Board Description + + The mvSMR is a 75x130mm single image processing board used + in automation. Power Supply is 24VDC. + +2 System Components + +2.1 CPU + Freescale MPC5200B CPU running at 400MHz core and 133MHz XLB/IPB. + 64MB DDR-I @ 133MHz. + 8 MByte Nor Flash on local bus. + 2 serial ports. Console running on ttyS0 @ 115200 8N1. + +2.2 PCI + PCI clock fixed at 33MHz due to old'n'slow Xilinx PCI core. + +2.3 FPGA + Xilinx Spartan-3 XC3S200 with PCI DMA engine. + Connects to Matrix Vision specific CCD/CMOS sensor interface. + +2.4 I2C + EEPROM @ 0xA0 for vendor specifics. + image sensor interface (slave addresses depend on sensor) + +3 Flash layout. + + reset vector is 0x00000100, i.e. "LOWBOOT". + + FF800000 u-boot + FF806000 u-boot script image + FF808000 u-boot environment + FF840000 FPGA raw bit file + FF880000 root FS + FFF00000 kernel + +4 Booting + + On startup the bootscript @ FF806000 is executed. This script can be + exchanged easily. Default boot mode is "boot from flash", i.e. system + works stand-alone. + + This behaviour depends on some environment variables : + + "netboot" : yes ->try dhcp/bootp and boot from network. + A "dhcp_client_id" and "dhcp_vendor-class-identifier" can be used for + DHCP server configuration, e.g. to provide different images to + different devices. + + During netboot the system tries to get 3 image files: + 1. Kernel - name + data is given during BOOTP. + 2. Initrd - name is stored in "initrd_name" + Fallback files are the flash versions. |