summaryrefslogtreecommitdiff
path: root/board/st-ericsson
diff options
context:
space:
mode:
Diffstat (limited to 'board/st-ericsson')
-rw-r--r--board/st-ericsson/u8500/u8500_href.c75
1 files changed, 1 insertions, 74 deletions
diff --git a/board/st-ericsson/u8500/u8500_href.c b/board/st-ericsson/u8500/u8500_href.c
index b4b8751..3de80df 100644
--- a/board/st-ericsson/u8500/u8500_href.c
+++ b/board/st-ericsson/u8500/u8500_href.c
@@ -138,18 +138,6 @@ void show_boot_progress(int progress)
}
#endif
-static unsigned int read_asicid(void)
-{
- unsigned int *address = (void *)U8500_BOOTROM_BASE
- + U8500_BOOTROM_ASIC_ID_OFFSET;
- return readl(address);
-}
-
-int cpu_is_u8500v11(void)
-{
- return read_asicid() == 0x008500A1;
-}
-
/*
* Miscellaneous platform dependent initialisations
*/
@@ -226,67 +214,6 @@ unsigned int addr_vall_arr[] = {
};
#ifdef CONFIG_BOARD_LATE_INIT
-#ifdef CONFIG_MMC
-
-#define LDO_VAUX3_MASK 0x3
-#define LDO_VAUX3_ENABLE 0x1
-#define VAUX3_VOLTAGE_2_9V 0xd
-
-#define AB8500_REGU_CTRL2 0x4
-#define AB8500_REGU_VRF1VAUX3_REGU_REG 0x040A
-#define AB8500_REGU_VRF1VAUX3_SEL_REG 0x0421
-
-static int hrefplus_mmc_power_init(void)
-{
- int ret;
- int val;
-
- if (!cpu_is_u8500v11())
- return 0;
-
- /*
- * On v1.1 HREF boards (HREF+), Vaux3 needs to be enabled for the SD
- * card to work. This is done by enabling the regulators in the AB8500
- * via PRCMU I2C transactions.
- *
- * This code is derived from the handling of AB8500_LDO_VAUX3 in
- * ab8500_ldo_enable() and ab8500_ldo_disable() in Linux.
- *
- * Turn off and delay is required to have it work across soft reboots.
- */
-
- ret = prcmu_i2c_read(AB8500_REGU_CTRL2, AB8500_REGU_VRF1VAUX3_REGU_REG);
- if (ret < 0)
- goto out;
-
- val = ret;
-
- /* Turn off */
- ret = prcmu_i2c_write(AB8500_REGU_CTRL2, AB8500_REGU_VRF1VAUX3_REGU_REG,
- val & ~LDO_VAUX3_MASK);
- if (ret < 0)
- goto out;
-
- udelay(10 * 1000);
-
- /* Set the voltage to 2.9V */
- ret = prcmu_i2c_write(AB8500_REGU_CTRL2,
- AB8500_REGU_VRF1VAUX3_SEL_REG,
- VAUX3_VOLTAGE_2_9V);
- if (ret < 0)
- goto out;
-
- val = val & ~LDO_VAUX3_MASK;
- val = val | LDO_VAUX3_ENABLE;
-
- /* Turn on the supply */
- ret = prcmu_i2c_write(AB8500_REGU_CTRL2,
- AB8500_REGU_VRF1VAUX3_REGU_REG, val);
-
-out:
- return ret;
-}
-#endif
/*
* called after all initialisation were done, but before the generic
* mmc_initialize().
@@ -313,7 +240,7 @@ int board_late_init(void)
setenv("board_id", "1");
}
#ifdef CONFIG_MMC
- hrefplus_mmc_power_init();
+ u8500_mmc_power_init();
/*
* config extended GPIO pins for level shifter and