summaryrefslogtreecommitdiff
path: root/board
diff options
context:
space:
mode:
Diffstat (limited to 'board')
-rw-r--r--board/csb226/memsetup.S36
-rw-r--r--board/innokom/flash.c3
-rw-r--r--board/innokom/innokom.c7
-rw-r--r--board/innokom/memsetup.S27
-rw-r--r--board/mpl/common/pci.c40
-rw-r--r--board/mpl/mip405/mip405.c15
-rw-r--r--board/svm_sc8xx/ppcboot.lds133
-rw-r--r--board/svm_sc8xx/ppcboot.lds.debug131
-rw-r--r--board/wepep250/Makefile47
-rw-r--r--board/wepep250/config.mk11
-rw-r--r--board/wepep250/flash.c321
-rw-r--r--board/wepep250/intel.h100
-rw-r--r--board/wepep250/memsetup.S147
-rw-r--r--board/wepep250/u-boot.lds55
-rw-r--r--board/wepep250/wepep250.c77
15 files changed, 841 insertions, 309 deletions
diff --git a/board/csb226/memsetup.S b/board/csb226/memsetup.S
index 6567184..60f9d50 100644
--- a/board/csb226/memsetup.S
+++ b/board/csb226/memsetup.S
@@ -38,6 +38,9 @@ DRAM_SIZE: .long CFG_DRAM_SIZE
sub pc,pc,#4
.endm
+_TEXT_BASE:
+ .word TEXT_BASE
+
/*
* Memory setup
@@ -222,23 +225,28 @@ mem_init:
/* Step 2c: Write FLYCNFG FIXME: what's that??? */
/* ---------------------------------------------------------------- */
+ /* test if we run from flash or RAM - RAM/BDI: don't setup RAM */
+ adr r3, mem_init /* r0 <- current position of code */
+ ldr r2, =mem_init
+ cmp r3, r2 /* skip init if in place */
+ beq initirqs
+
/* ---------------------------------------------------------------- */
/* Step 2d: Initialize Timing for Sync Memory (SDCLK0) */
/* ---------------------------------------------------------------- */
/* Before accessing MDREFR we need a valid DRI field, so we set */
- /* this to power on defaults + DIR field. */
+ /* this to power on defaults + DRI field. */
- ldr r4, =0x03ca4fff
- str r4, [r1, #MDREFR_OFFSET] /* write back MDREFR */
- ldr r4, [r1, #MDREFR_OFFSET]
+ ldr r3, =CFG_MDREFR_VAL
+ ldr r2, =0xFFF
+ and r3, r3, r2
+ ldr r4, =0x03ca4000
+ orr r4, r4, r3
- ldr r4, =0x03ca4030
str r4, [r1, #MDREFR_OFFSET] /* write back MDREFR */
- ldr r4, [r1, #MDREFR_OFFSET]
-
- /* Note: preserve the mdrefr value in r4 */
+ ldr r4, [r1, #MDREFR_OFFSET]
/* ---------------------------------------------------------------- */
@@ -258,18 +266,16 @@ mem_init:
/* Step 4: Initialize SDRAM */
/* ---------------------------------------------------------------- */
- /* Step 4a: assert MDREFR:K1RUN and MDREFR:K2RUN and configure */
+ /* Step 4a: assert MDREFR:K?RUN and configure */
/* MDREFR:K1DB2 and MDREFR:K2DB2 as desired. */
- orr r4, r4, #(MDREFR_K1RUN|MDREFR_K0RUN)
-
- str r4, [r1, #MDREFR_OFFSET] /* write back MDREFR */
- ldr r4, [r1, #MDREFR_OFFSET]
-
+ ldr r4, =CFG_MDREFR_VAL
+ str r4, [r1, #MDREFR_OFFSET] /* write back MDREFR */
+ ldr r4, [r1, #MDREFR_OFFSET]
/* Step 4b: de-assert MDREFR:SLFRSH. */
- bic r4, r4, #(MDREFR_SLFRSH)
+ bic r4, r4, #(MDREFR_SLFRSH)
str r4, [r1, #MDREFR_OFFSET] /* write back MDREFR */
ldr r4, [r1, #MDREFR_OFFSET]
diff --git a/board/innokom/flash.c b/board/innokom/flash.c
index 32c57d8..b7c2072 100644
--- a/board/innokom/flash.c
+++ b/board/innokom/flash.c
@@ -10,7 +10,8 @@
* Robert Schwebel, Pengutronix, <r.schwebel@pengutronix.de>
*
* (C) Copyright 2002
- * Kai-Uwe Bloem, GDS, <kai-uwe.bloem@auerswald.de>
+ * Auerswald GmbH & Co KG, Germany
+ * Kai-Uwe Bloem <kai-uwe.bloem@auerswald.de>
*
* See file CREDITS for list of people who contributed to this
* project.
diff --git a/board/innokom/innokom.c b/board/innokom/innokom.c
index 5ee5117..da238da 100644
--- a/board/innokom/innokom.c
+++ b/board/innokom/innokom.c
@@ -48,7 +48,7 @@ int i2c_init_board(void)
icr = ICR; ICR &= ~(ICR_SCLE | ICR_IUE);
/* set gpio pin low _before_ we change direction to output */
- GPCR(70) = GPIO_bit(70);
+ GPCR(70) = GPIO_bit(70);
/* now toggle between output=low and high-impedance */
for (i = 0; i < 20; i++) {
@@ -100,13 +100,8 @@ int board_init (void)
/* memory and cpu-speed are setup before relocation */
/* so we do _nothing_ here */
- /* arch number of Innokom board */
gd->bd->bi_arch_number = MACH_TYPE_INNOKOM;
-
- /* adress of boot parameters */
gd->bd->bi_boot_params = 0xa0000100;
-
- /* baud rate */
gd->bd->bi_baudrate = CONFIG_BAUDRATE;
return 0;
diff --git a/board/innokom/memsetup.S b/board/innokom/memsetup.S
index a2bc99d..60f9d50 100644
--- a/board/innokom/memsetup.S
+++ b/board/innokom/memsetup.S
@@ -237,17 +237,16 @@ mem_init:
/* ---------------------------------------------------------------- */
/* Before accessing MDREFR we need a valid DRI field, so we set */
- /* this to power on defaults + DIR field. */
+ /* this to power on defaults + DRI field. */
- ldr r4, =0x03ca4fff
- str r4, [r1, #MDREFR_OFFSET] /* write back MDREFR */
- ldr r4, [r1, #MDREFR_OFFSET]
+ ldr r3, =CFG_MDREFR_VAL
+ ldr r2, =0xFFF
+ and r3, r3, r2
+ ldr r4, =0x03ca4000
+ orr r4, r4, r3
- ldr r4, =0x03ca4030
str r4, [r1, #MDREFR_OFFSET] /* write back MDREFR */
- ldr r4, [r1, #MDREFR_OFFSET]
-
- /* Note: preserve the mdrefr value in r4 */
+ ldr r4, [r1, #MDREFR_OFFSET]
/* ---------------------------------------------------------------- */
@@ -267,18 +266,16 @@ mem_init:
/* Step 4: Initialize SDRAM */
/* ---------------------------------------------------------------- */
- /* Step 4a: assert MDREFR:K1RUN and MDREFR:K2RUN and configure */
+ /* Step 4a: assert MDREFR:K?RUN and configure */
/* MDREFR:K1DB2 and MDREFR:K2DB2 as desired. */
- orr r4, r4, #(MDREFR_K1RUN|MDREFR_K0RUN)
-
- str r4, [r1, #MDREFR_OFFSET] /* write back MDREFR */
- ldr r4, [r1, #MDREFR_OFFSET]
-
+ ldr r4, =CFG_MDREFR_VAL
+ str r4, [r1, #MDREFR_OFFSET] /* write back MDREFR */
+ ldr r4, [r1, #MDREFR_OFFSET]
/* Step 4b: de-assert MDREFR:SLFRSH. */
- bic r4, r4, #(MDREFR_SLFRSH)
+ bic r4, r4, #(MDREFR_SLFRSH)
str r4, [r1, #MDREFR_OFFSET] /* write back MDREFR */
ldr r4, [r1, #MDREFR_OFFSET]
diff --git a/board/mpl/common/pci.c b/board/mpl/common/pci.c
index a26f542..692930b 100644
--- a/board/mpl/common/pci.c
+++ b/board/mpl/common/pci.c
@@ -65,21 +65,22 @@ void pci_pip405_write_regs(struct pci_controller *hose, pci_dev_t dev,
static void pci_pip405_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
{
unsigned char int_line = 0xff;
+ unsigned char pin;
/*
* Write pci interrupt line register
*/
if(PCI_DEV(dev)==0) /* Device0 = PPC405 -> skip */
return;
- if(PCI_FUNC(dev)==0)
- {
- /* assuming all function 0 are using their INTA# Pin*/
- int_line=PCI_IRQ_VECTOR(dev);
- pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, int_line);
+ pci_hose_read_config_byte(hose, dev, PCI_INTERRUPT_PIN, &pin);
+ if ((pin == 0) || (pin > 4))
+ return;
+
+ int_line = ((PCI_DEV(dev) + (pin-1) + 10) % 4) + 28;
+ pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, int_line);
#ifdef DEBUG
- printf("Fixup IRQ: dev %d (%x) int line %d 0x%x\n",
- PCI_DEV(dev),dev,int_line,int_line);
+ printf("Fixup IRQ: dev %d (%x) int line %d 0x%x\n",
+ PCI_DEV(dev),dev,int_line,int_line);
#endif
- }
}
extern void pci_405gp_init(struct pci_controller *hose);
@@ -90,11 +91,34 @@ static struct pci_controller hose = {
fixup_irq: pci_pip405_fixup_irq,
};
+
+static void reloc_pci_cfg_table(struct pci_config_table *table)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+ unsigned long addr;
+
+ for (; table && table->vendor; table++) {
+ addr = (ulong) (table->config_device) + gd->reloc_off;
+#ifdef DEBUG
+ printf ("device \"%d\": 0x%08lx => 0x%08lx\n",
+ table->device, (ulong) (table->config_device), addr);
+#endif
+ table->config_device =
+ (void (*)(struct pci_controller* hose, pci_dev_t dev,
+ struct pci_config_table *))addr;
+ table->priv[0]+=gd->reloc_off;
+ }
+}
+
void pci_init_board(void)
{
/*we want the ptrs to RAM not flash (ie don't use init list)*/
hose.fixup_irq = pci_pip405_fixup_irq;
hose.config_table = pci_pip405_config_table;
+ reloc_pci_cfg_table(hose.config_table);
+#ifdef DEBUG
+ printf("Init PCI: fixup_irq=%p config_table=%p hose=%p\n",pci_pip405_fixup_irq,pci_pip405_config_table,hose);
+#endif
pci_405gp_init(&hose);
}
diff --git a/board/mpl/mip405/mip405.c b/board/mpl/mip405/mip405.c
index 8bab47c..95ad97c 100644
--- a/board/mpl/mip405/mip405.c
+++ b/board/mpl/mip405/mip405.c
@@ -128,6 +128,15 @@ const sdram_t sdram_table[] = {
2, /* Address Mode = 2 */
4, /* size value */
1}, /* ECC enabled */
+ { 0x03, /* Rev A, 128MByte -4 Board */
+ 3, /* Case Latenty = 3 */
+ 3, /* trp 20ns / 7.5 ns datain[27] */
+ 3, /* trcd 20ns /7.5 ns (datain[29]) */
+ 6, /* tras 44ns /7.5 ns (datain[30]) */
+ 4, /* tcpt 44 - 20ns = 24ns */
+ 3, /* Address Mode = 3 */
+ 5, /* size value */
+ 1}, /* ECC enabled */
{ 0xff, /* terminator */
0xff,
0xff,
@@ -616,9 +625,15 @@ void print_mip405_rev (void)
int last_stage_init (void)
{
+ /* write correct LED configuration */
if (miiphy_write (0x1, 0x14, 0x2402) != 0) {
printf ("Error writing to the PHY\n");
}
+ /* since LED/CFG2 is not connected on the -2,
+ * write to correct capability information */
+ if (miiphy_write (0x1, 0x4, 0x01E1) != 0) {
+ printf ("Error writing to the PHY\n");
+ }
print_mip405_rev ();
show_stdio_dev ();
check_env ();
diff --git a/board/svm_sc8xx/ppcboot.lds b/board/svm_sc8xx/ppcboot.lds
deleted file mode 100644
index 5f5e2e4..0000000
--- a/board/svm_sc8xx/ppcboot.lds
+++ /dev/null
@@ -1,133 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-OUTPUT_ARCH(powerpc)
-SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
-/* Do we need any of these for elf?
- __DYNAMIC = 0; */
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .interp : { *(.interp) }
- .hash : { *(.hash) }
- .dynsym : { *(.dynsym) }
- .dynstr : { *(.dynstr) }
- .rel.text : { *(.rel.text) }
- .rela.text : { *(.rela.text) }
- .rel.data : { *(.rel.data) }
- .rela.data : { *(.rela.data) }
- .rel.rodata : { *(.rel.rodata) }
- .rela.rodata : { *(.rela.rodata) }
- .rel.got : { *(.rel.got) }
- .rela.got : { *(.rela.got) }
- .rel.ctors : { *(.rel.ctors) }
- .rela.ctors : { *(.rela.ctors) }
- .rel.dtors : { *(.rel.dtors) }
- .rela.dtors : { *(.rela.dtors) }
- .rel.bss : { *(.rel.bss) }
- .rela.bss : { *(.rela.bss) }
- .rel.plt : { *(.rel.plt) }
- .rela.plt : { *(.rela.plt) }
- .init : { *(.init) }
- .plt : { *(.plt) }
- .text :
- {
- /* WARNING - the following is hand-optimized to fit within */
- /* the sector layout of our flash chips! XXX FIXME XXX */
-
- cpu/mpc8xx/start.o (.text)
- common/dlmalloc.o (.text)
- ppc/ppcstring.o (.text)
- ppc/vsprintf.o (.text)
- ppc/crc32.o (.text)
- ppc/zlib.o (.text)
-
- . = env_offset;
- common/environment.o(.text)
-
- *(.text)
- *(.fixup)
- *(.got1)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(.rodata)
- *(.rodata1)
- }
- .fini : { *(.fini) } =0
- .ctors : { *(.ctors) }
- .dtors : { *(.dtors) }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x00FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- *(.got)
- _GOT2_TABLE_ = .;
- *(.got2)
- _FIXUP_TABLE_ = .;
- *(.fixup)
- }
- __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data)
- *(.data1)
- *(.sdata)
- *(.sdata2)
- *(.dynamic)
- CONSTRUCTORS
- }
- _edata = .;
- PROVIDE (edata = .);
-
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss :
- {
- *(.sbss) *(.scommon)
- *(.dynbss)
- *(.bss)
- *(COMMON)
- }
- _end = . ;
- PROVIDE (end = .);
-}
-
diff --git a/board/svm_sc8xx/ppcboot.lds.debug b/board/svm_sc8xx/ppcboot.lds.debug
deleted file mode 100644
index f230a6b..0000000
--- a/board/svm_sc8xx/ppcboot.lds.debug
+++ /dev/null
@@ -1,131 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-OUTPUT_ARCH(powerpc)
-SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
-/* Do we need any of these for elf?
- __DYNAMIC = 0; */
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .interp : { *(.interp) }
- .hash : { *(.hash) }
- .dynsym : { *(.dynsym) }
- .dynstr : { *(.dynstr) }
- .rel.text : { *(.rel.text) }
- .rela.text : { *(.rela.text) }
- .rel.data : { *(.rel.data) }
- .rela.data : { *(.rela.data) }
- .rel.rodata : { *(.rel.rodata) }
- .rela.rodata : { *(.rela.rodata) }
- .rel.got : { *(.rel.got) }
- .rela.got : { *(.rela.got) }
- .rel.ctors : { *(.rel.ctors) }
- .rela.ctors : { *(.rela.ctors) }
- .rel.dtors : { *(.rel.dtors) }
- .rela.dtors : { *(.rela.dtors) }
- .rel.bss : { *(.rel.bss) }
- .rela.bss : { *(.rela.bss) }
- .rel.plt : { *(.rel.plt) }
- .rela.plt : { *(.rela.plt) }
- .init : { *(.init) }
- .plt : { *(.plt) }
- .text :
- {
- /* WARNING - the following is hand-optimized to fit within */
- /* the sector layout of our flash chips! XXX FIXME XXX */
-
- cpu/mpc8xx/start.o (.text)
- common/dlmalloc.o (.text)
- ppc/vsprintf.o (.text)
- ppc/crc32.o (.text)
-
- . = env_offset;
- common/environment.o(.text)
-
- *(.text)
- *(.fixup)
- *(.got1)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(.rodata)
- *(.rodata1)
- }
- .fini : { *(.fini) } =0
- .ctors : { *(.ctors) }
- .dtors : { *(.dtors) }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x0FFF) & 0xFFFFF000;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- *(.got)
- _GOT2_TABLE_ = .;
- *(.got2)
- _FIXUP_TABLE_ = .;
- *(.fixup)
- }
- __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data)
- *(.data1)
- *(.sdata)
- *(.sdata2)
- *(.dynamic)
- CONSTRUCTORS
- }
- _edata = .;
- PROVIDE (edata = .);
-
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(4096);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(4096);
- __init_end = .;
-
- __bss_start = .;
- .bss :
- {
- *(.sbss) *(.scommon)
- *(.dynbss)
- *(.bss)
- *(COMMON)
- }
- _end = . ;
- PROVIDE (end = .);
-}
-
diff --git a/board/wepep250/Makefile b/board/wepep250/Makefile
new file mode 100644
index 0000000..d4314d7
--- /dev/null
+++ b/board/wepep250/Makefile
@@ -0,0 +1,47 @@
+#
+# (C) Copyright 2000, 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = lib$(BOARD).a
+
+OBJS := wepep250.o flash.o
+SOBJS := memsetup.o
+
+$(LIB): $(OBJS) $(SOBJS)
+ $(AR) crv $@ $^
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+ $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################
diff --git a/board/wepep250/config.mk b/board/wepep250/config.mk
new file mode 100644
index 0000000..792f0ee
--- /dev/null
+++ b/board/wepep250/config.mk
@@ -0,0 +1,11 @@
+#
+# This is config used for compilation of WEP EP250 sources
+#
+# You might change location of U-Boot in memory by setting right TEXT_BASE.
+# This allows for example having one copy located at the end of ram and stored
+# in flash device and later on while developing use other location to test
+# the code in RAM device only.
+#
+
+TEXT_BASE = 0xa1fe0000
+#TEXT_BASE = 0xa1001000 \ No newline at end of file
diff --git a/board/wepep250/flash.c b/board/wepep250/flash.c
new file mode 100644
index 0000000..319dddc
--- /dev/null
+++ b/board/wepep250/flash.c
@@ -0,0 +1,321 @@
+/*
+ * Copyright (C) 2003 ETC s.r.o.
+ *
+ * This code was inspired by Marius Groeger and Kyle Harris code
+ * available in other board ports for U-Boot
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Written by Peter Figuli <peposh@etc.sk>, 2003.
+ *
+ */
+
+#include <common.h>
+#include "intel.h"
+
+
+/*
+ * This code should handle CFI FLASH memory device. This code is very
+ * minimalistic approach without many essential error handling code as well.
+ * Because U-Boot actually is missing smart handling of FLASH device,
+ * we just set flash_id to anything else to FLASH_UNKNOW, so common code
+ * can call us without any restrictions.
+ * TODO: Add CFI Query, to be able to determine FLASH device.
+ * TODO: Add error handling code
+ * NOTE: This code was tested with BUS_WIDTH 4 and ITERLEAVE 2 only, but
+ * hopefully may work with other configurations.
+ */
+
+#if ( WEP_FLASH_BUS_WIDTH == 1 )
+# define FLASH_BUS vu_char
+# if ( WEP_FLASH_INTERLEAVE == 1 )
+# define FLASH_CMD( x ) x
+# else
+# error "With 8bit bus only one chip is allowed"
+# endif
+
+
+#elif ( WEP_FLASH_BUS_WIDTH == 2 )
+# define FLASH_BUS vu_short
+# if ( WEP_FLASH_INTERLEAVE == 1 )
+# define FLASH_CMD( x ) x
+# elif ( WEP_FLASH_INTERLEAVE == 2 )
+# define FLASH_CMD( x ) (( x << 8 )| x )
+# else
+# error "With 16bit bus only 1 or 2 chip(s) are allowed"
+# endif
+
+
+#elif ( WEP_FLASH_BUS_WIDTH == 4 )
+# define FLASH_BUS vu_long
+# if ( WEP_FLASH_INTERLEAVE == 1 )
+# define FLASH_CMD( x ) x
+# elif ( WEP_FLASH_INTERLEAVE == 2 )
+# define FLASH_CMD( x ) (( x << 16 )| x )
+# elif ( WEP_FLASH_INTERLEAVE == 4 )
+# define FLASH_CMD( x ) (( x << 24 )|( x << 16 ) ( x << 8 )| x )
+# else
+# error "With 32bit bus only 1,2 or 4 chip(s) are allowed"
+# endif
+
+#else
+# error "Flash bus width might be 1,2,4 for 8,16,32 bit configuration"
+#endif
+
+
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];
+
+static FLASH_BUS flash_status_reg (void)
+{
+
+ FLASH_BUS *addr = (FLASH_BUS *) 0;
+
+ *addr = FLASH_CMD (CFI_INTEL_CMD_READ_STATUS_REGISTER);
+
+ return *addr;
+}
+
+static int flash_ready (ulong timeout)
+{
+ int ok = 1;
+
+ reset_timer_masked ();
+ while ((flash_status_reg () & FLASH_CMD (CFI_INTEL_SR_READY)) !=
+ FLASH_CMD (CFI_INTEL_SR_READY)) {
+ if (get_timer_masked () > timeout && timeout != 0) {
+ ok = 0;
+ break;
+ }
+ }
+ return ok;
+}
+
+#if ( CFG_MAX_FLASH_BANKS != 1 )
+# error "WEP platform has only one flash bank!"
+#endif
+
+
+ulong flash_init (void)
+{
+ int i;
+ FLASH_BUS address = WEP_FLASH_BASE;
+
+ flash_info[0].size = WEP_FLASH_BANK_SIZE;
+ flash_info[0].sector_count = CFG_MAX_FLASH_SECT;
+ flash_info[0].flash_id = INTEL_MANUFACT;
+ memset (flash_info[0].protect, 0, CFG_MAX_FLASH_SECT);
+
+ for (i = 0; i < CFG_MAX_FLASH_SECT; i++) {
+ flash_info[0].start[i] = address;
+#ifdef WEP_FLASH_UNLOCK
+ /* Some devices are hw locked after start. */
+ *((FLASH_BUS *) address) = FLASH_CMD (CFI_INTEL_CMD_LOCK_SETUP);
+ *((FLASH_BUS *) address) = FLASH_CMD (CFI_INTEL_CMD_UNLOCK_BLOCK);
+ flash_ready (0);
+ *((FLASH_BUS *) address) = FLASH_CMD (CFI_INTEL_CMD_READ_ARRAY);
+#endif
+ address += WEP_FLASH_SECT_SIZE;
+ }
+
+ flash_protect (FLAG_PROTECT_SET,
+ CFG_FLASH_BASE,
+ CFG_FLASH_BASE + _armboot_end_data - _armboot_start,
+ &flash_info[0]);
+
+ flash_protect (FLAG_PROTECT_SET,
+ CFG_ENV_ADDR,
+ CFG_ENV_ADDR + CFG_ENV_SIZE - 1, &flash_info[0]);
+
+ return WEP_FLASH_BANK_SIZE;
+}
+
+void flash_print_info (flash_info_t * info)
+{
+ int i;
+
+ printf (" Intel vendor\n");
+ printf (" Size: %ld MB in %d Sectors\n",
+ info->size >> 20, info->sector_count);
+
+ printf (" Sector Start Addresses:");
+ for (i = 0; i < info->sector_count; i++) {
+ if (!(i % 5)) {
+ printf ("\n");
+ }
+
+ printf (" %08lX%s", info->start[i],
+ info->protect[i] ? " (RO)" : " ");
+ }
+ printf ("\n");
+}
+
+
+int flash_erase (flash_info_t * info, int s_first, int s_last)
+{
+ int flag, non_protected = 0, sector;
+ int rc = ERR_OK;
+
+ FLASH_BUS *address;
+
+ for (sector = s_first; sector <= s_last; sector++) {
+ if (!info->protect[sector]) {
+ non_protected++;
+ }
+ }
+
+ if (!non_protected) {
+ return ERR_PROTECTED;
+ }
+
+ /*
+ * Disable interrupts which might cause a timeout
+ * here. Remember that our exception vectors are
+ * at address 0 in the flash, and we don't want a
+ * (ticker) exception to happen while the flash
+ * chip is in programming mode.
+ */
+ flag = disable_interrupts ();
+
+
+ /* Start erase on unprotected sectors */
+ for (sector = s_first; sector <= s_last && !ctrlc (); sector++) {
+ if (info->protect[sector]) {
+ printf ("Protected sector %2d skipping...\n", sector);
+ continue;
+ } else {
+ printf ("Erasing sector %2d ... ", sector);
+ }
+
+ address = (FLASH_BUS *) (info->start[sector]);
+
+ *address = FLASH_CMD (CFI_INTEL_CMD_BLOCK_ERASE);
+ *address = FLASH_CMD (CFI_INTEL_CMD_CONFIRM);
+ if (flash_ready (CFG_FLASH_ERASE_TOUT)) {
+ *address = FLASH_CMD (CFI_INTEL_CMD_CLEAR_STATUS_REGISTER);
+ printf ("ok.\n");
+ } else {
+ *address = FLASH_CMD (CFI_INTEL_CMD_SUSPEND);
+ rc = ERR_TIMOUT;
+ printf ("timeout! Aborting...\n");
+ break;
+ }
+ *address = FLASH_CMD (CFI_INTEL_CMD_READ_ARRAY);
+ }
+ if (ctrlc ())
+ printf ("User Interrupt!\n");
+
+ /* allow flash to settle - wait 10 ms */
+ udelay_masked (10000);
+ if (flag) {
+ enable_interrupts ();
+ }
+
+ return rc;
+}
+
+static int write_data (flash_info_t * info, ulong dest, FLASH_BUS data)
+{
+ FLASH_BUS *address = (FLASH_BUS *) dest;
+ int rc = ERR_OK;
+ int flag;
+
+ /* Check if Flash is (sufficiently) erased */
+ if ((*address & data) != data) {
+ return ERR_NOT_ERASED;
+ }
+
+ /*
+ * Disable interrupts which might cause a timeout
+ * here. Remember that our exception vectors are
+ * at address 0 in the flash, and we don't want a
+ * (ticker) exception to happen while the flash
+ * chip is in programming mode.
+ */
+
+ flag = disable_interrupts ();
+
+ *address = FLASH_CMD (CFI_INTEL_CMD_CLEAR_STATUS_REGISTER);
+ *address = FLASH_CMD (CFI_INTEL_CMD_PROGRAM1);
+ *address = data;
+
+ if (!flash_ready (CFG_FLASH_WRITE_TOUT)) {
+ *address = FLASH_CMD (CFI_INTEL_CMD_SUSPEND);
+ rc = ERR_TIMOUT;
+ printf ("timeout! Aborting...\n");
+ }
+
+ *address = FLASH_CMD (CFI_INTEL_CMD_READ_ARRAY);
+ if (flag) {
+ enable_interrupts ();
+ }
+
+ return rc;
+}
+
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+ ulong read_addr, write_addr;
+ FLASH_BUS data;
+ int i, result = ERR_OK;
+
+
+ read_addr = addr & ~(sizeof (FLASH_BUS) - 1);
+ write_addr = read_addr;
+ if (read_addr != addr) {
+ data = 0;
+ for (i = 0; i < sizeof (FLASH_BUS); i++) {
+ if (read_addr < addr || cnt == 0) {
+ data |= *((uchar *) read_addr) << i * 8;
+ } else {
+ data |= (*src++) << i * 8;
+ cnt--;
+ }
+ read_addr++;
+ }
+ if ((result = write_data (info, write_addr, data)) != ERR_OK) {
+ return result;
+ }
+ write_addr += sizeof (FLASH_BUS);
+ }
+ for (; cnt >= sizeof (FLASH_BUS); cnt -= sizeof (FLASH_BUS)) {
+ if ((result = write_data (info, write_addr,
+ *((FLASH_BUS *) src))) != ERR_OK) {
+ return result;
+ }
+ write_addr += sizeof (FLASH_BUS);
+ src += sizeof (FLASH_BUS);
+ }
+ if (cnt > 0) {
+ read_addr = write_addr;
+ data = 0;
+ for (i = 0; i < sizeof (FLASH_BUS); i++) {
+ if (cnt > 0) {
+ data |= (*src++) << i * 8;
+ cnt--;
+ } else {
+ data |= *((uchar *) read_addr) << i * 8;
+ }
+ read_addr++;
+ }
+ if ((result = write_data (info, write_addr, data)) != 0) {
+ return result;
+ }
+ }
+ return ERR_OK;
+}
diff --git a/board/wepep250/intel.h b/board/wepep250/intel.h
new file mode 100644
index 0000000..f622590
--- /dev/null
+++ b/board/wepep250/intel.h
@@ -0,0 +1,100 @@
+/*
+ * Copyright (C) 2002 ETC s.r.o.
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * 3. Neither the name of the ETC s.r.o. nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * Written by Marcel Telka <marcel@telka.sk>, 2002.
+ *
+ * Documentation:
+ * [1] Intel Corporation, "3 Volt Intel Strata Flash Memory 28F128J3A, 28F640J3A,
+ * 28F320J3A (x8/x16)", April 2002, Order Number: 290667-011
+ * [2] Intel Corporation, "3 Volt Synchronous Intel Strata Flash Memory 28F640K3, 28F640K18,
+ * 28F128K3, 28F128K18, 28F256K3, 28F256K18 (x16)", June 2002, Order Number: 290737-005
+ *
+ * This file is taken from OpenWinCE project hosted by SourceForge.net
+ *
+ */
+
+#ifndef FLASH_INTEL_H
+#define FLASH_INTEL_H
+
+#include <common.h>
+
+/* Intel CFI commands - see Table 4. in [1] and Table 3. in [2] */
+
+#define CFI_INTEL_CMD_READ_ARRAY 0xFF /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_CMD_READ_IDENTIFIER 0x90 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_CMD_READ_QUERY 0x98 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_CMD_READ_STATUS_REGISTER 0x70 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_CMD_CLEAR_STATUS_REGISTER 0x50 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_CMD_PROGRAM1 0x40 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_CMD_PROGRAM2 0x10 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_CMD_WRITE_TO_BUFFER 0xE8 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_CMD_CONFIRM 0xD0 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_CMD_BLOCK_ERASE 0x20 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_CMD_SUSPEND 0xB0 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_CMD_RESUME 0xD0 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_CMD_LOCK_SETUP 0x60 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_CMD_LOCK_BLOCK 0x01 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_CMD_UNLOCK_BLOCK 0xD0 /* 28FxxxJ3A - unlocks all blocks, 28FFxxxK3, 28FxxxK18 */
+#define CFI_INTEL_CMD_LOCK_DOWN_BLOCK 0x2F /* 28FxxxK3, 28FxxxK18 */
+
+/* Intel CFI Status Register bits - see Table 6. in [1] and Table 7. in [2] */
+
+#define CFI_INTEL_SR_READY 1 << 7 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_SR_ERASE_SUSPEND 1 << 6 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_SR_ERASE_ERROR 1 << 5 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_SR_PROGRAM_ERROR 1 << 4 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_SR_VPEN_ERROR 1 << 3 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_SR_PROGRAM_SUSPEND 1 << 2 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_SR_BLOCK_LOCKED 1 << 1 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */
+#define CFI_INTEL_SR_BEFP 1 << 0 /* 28FxxxK3, 28FxxxK18 */
+
+/* Intel flash device ID codes for 28FxxxJ3A - see Table 5. in [1] */
+
+#define CFI_CHIP_INTEL_28F320J3A 0x0016
+#define CFI_CHIPN_INTEL_28F320J3A "28F320J3A"
+#define CFI_CHIP_INTEL_28F640J3A 0x0017
+#define CFI_CHIPN_INTEL_28F640J3A "28F640J3A"
+#define CFI_CHIP_INTEL_28F128J3A 0x0018
+#define CFI_CHIPN_INTEL_28F128J3A "28F128J3A"
+
+/* Intel flash device ID codes for 28FxxxK3 and 28FxxxK18 - see Table 8. in [2] */
+
+#define CFI_CHIP_INTEL_28F640K3 0x8801
+#define CFI_CHIPN_INTEL_28F640K3 "28F640K3"
+#define CFI_CHIP_INTEL_28F128K3 0x8802
+#define CFI_CHIPN_INTEL_28F128K3 "28F128K3"
+#define CFI_CHIP_INTEL_28F256K3 0x8803
+#define CFI_CHIPN_INTEL_28F256K3 "28F256K3"
+#define CFI_CHIP_INTEL_28F640K18 0x8805
+#define CFI_CHIPN_INTEL_28F640K18 "28F640K18"
+#define CFI_CHIP_INTEL_28F128K18 0x8806
+#define CFI_CHIPN_INTEL_28F128K18 "28F128K18"
+#define CFI_CHIP_INTEL_28F256K18 0x8807
+#define CFI_CHIPN_INTEL_28F256K18 "28F256K18"
+
+#endif /* FLASH_INTEL_H */
+
diff --git a/board/wepep250/memsetup.S b/board/wepep250/memsetup.S
new file mode 100644
index 0000000..8a5d42f
--- /dev/null
+++ b/board/wepep250/memsetup.S
@@ -0,0 +1,147 @@
+/*
+ * Copyright (C) 2001, 2002 ETC s.r.o.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA
+ * 02111-1307, USA.
+ *
+ * Written by Marcel Telka <marcel@telka.sk>, 2001, 2002.
+ * Changes for U-Boot Peter Figuli <peposh@etc.sk>, 2003.
+ *
+ * This file is taken from OpenWinCE project hosted by SourceForge.net
+ *
+ * Documentation:
+ * [1] Intel Corporation, "Intel PXA250 and PXA210 Application Processors
+ * Developer's Manual", February 2002, Order Number: 278522-001
+ * [2] Samsung Electronics, "8Mx16 SDRAM 54CSP K4S281633D-RL/N/P",
+ * Revision 1.0, February 2002
+ * [3] Samsung Electronics, "16Mx16 SDRAM 54CSP K4S561633C-RL(N)",
+ * Revision 1.0, February 2002
+ *
+*/
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/pxa-regs.h>
+
+.globl memsetup
+memsetup:
+
+ mov r10, lr
+
+/* setup memory - see 6.12 in [1]
+ * Step 1 - wait 200 us
+ */
+ mov r0,#0x2700 /* wait 200 us @ 99.5 MHz */
+1: subs r0, r0, #1
+ bne 1b
+/* TODO: complete step 1 for Synchronous Static memory*/
+
+ ldr r0, =0x48000000 /* MC_BASE */
+
+
+
+/* step 1.a - setup MSCx
+ */
+ ldr r1, =0x000012B3 /* MSC0_RRR0(1) | MSC0_RDN0(2) | MSC0_RDF0(11) | MSC0_RT0(3) */
+ str r1, [r0, #0x8] /* MSC0_OFFSET */
+
+/* step 1.c - clear MDREFR:K1FREE, set MDREFR:DRI
+ * see AUTO REFRESH chapter in section D. in [2] and in [3]
+ * DRI = (64ms / 4096) * 99.53MHz / 32 = 48 for K4S281633
+ * DRI = (64ms / 8192) * 99.52MHz / 32 = 24 for K4S561633
+ * TODO: complete for Synchronous Static memory
+ */
+ ldr r1, [r0, #4] /* MDREFR_OFFSET */
+ ldr r2, =0x01000FFF /* MDREFR_K1FREE | MDREFR_DRI_MASK */
+ bic r1, r1, r2
+#if defined( WEP_SDRAM_K4S281633 )
+ orr r1, r1, #48 /* MDREFR_DRI(48) */
+#elif defined( WEP_SDRAM_K4S561633 )
+ orr r1, r1, #24 /* MDREFR_DRI(24) */
+#else
+#error SDRAM chip is not defined
+#endif
+
+ str r1, [r0, #4] /* MDREFR_OFFSET */
+
+/* Step 2 - only for Synchronous Static memory (TODO)
+ *
+ * Step 3 - same as step 4
+ *
+ * Step 4
+ *
+ * Step 4.a - set MDREFR:K1RUN, clear MDREFR:K1DB2
+ */
+ orr r1, r1, #0x00010000 /* MDREFR_K1RUN */
+ bic r1, r1, #0x00020000 /* MDREFR_K1DB2 */
+ str r1, [r0, #4] /* MDREFR_OFFSET */
+
+/* Step 4.b - clear MDREFR:SLFRSH */
+ bic r1, r1, #0x00400000 /* MDREFR_SLFRSH */
+ str r1, [r0, #4] /* MDREFR_OFFSET */
+
+/* Step 4.c - set MDREFR:E1PIN */
+ orr r1, r1, #0x00008000 /* MDREFR_E1PIN */
+ str r1, [r0, #4] /* MDREFR_OFFSET */
+
+/* Step 4.d - automatically done
+ *
+ * Steps 4.e and 4.f - configure SDRAM
+ */
+#if defined( WEP_SDRAM_K4S281633 )
+ ldr r1, =0x00000AA8 /* MDCNFG_DTC0(2) | MDCNFG_DLATCH0 | MDCNFG_DCAC0(1) | MDCNFG_DRAC0(1) | MDCNFG_DNB0 */
+#elif defined( WEP_SDRAM_K4S561633 )
+ ldr r1, =0x00000AC8 /* MDCNFG_DTC0(2) | MDCNFG_DLATCH0 | MDCNFG_DCAC0(1) | MDCNFG_DRAC0(2) | MDCNFG_DNB0 */
+#else
+#error SDRAM chip is not defined
+#endif
+ str r1, [r0, #0] /* MDCNFG_OFFSET */
+
+/* Step 5 - wait at least 200 us for SDRAM
+ * see section B. in [2]
+ */
+ mov r2,#0x2700 /* wait 200 us @ 99.5 MHz */
+1: subs r2, r2, #1
+ bne 1b
+
+/* Step 6 - after reset dcache is disabled, so automatically done
+ *
+ * Step 7 - eight refresh cycles
+ */
+ mov r2, #0xA0000000
+ ldr r3, [r2]
+ ldr r3, [r2]
+ ldr r3, [r2]
+ ldr r3, [r2]
+ ldr r3, [r2]
+ ldr r3, [r2]
+ ldr r3, [r2]
+ ldr r3, [r2]
+
+/* Step 8 - we don't need dcache now
+ *
+ * Step 9 - enable SDRAM partition 0
+ */
+ orr r1, r1, #1 /* MDCNFG_DE0 */
+ str r1, [r0, #0] /* MDCNFG_OFFSET */
+
+/* Step 10 - write MDMRS */
+ mov r1, #0
+ str r1, [r0, #0x40] /* MDMRS_OFFSET */
+
+/* Step 11 - optional (TODO) */
+
+ mov pc,r10
+
diff --git a/board/wepep250/u-boot.lds b/board/wepep250/u-boot.lds
new file mode 100644
index 0000000..280fc48
--- /dev/null
+++ b/board/wepep250/u-boot.lds
@@ -0,0 +1,55 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0x00000000;
+
+ . = ALIGN(4);
+ .text :
+ {
+ cpu/xscale/start.o (.text)
+ *(.text)
+ }
+
+ . = ALIGN(4);
+ .rodata : { *(.rodata) }
+
+ . = ALIGN(4);
+ .data : { *(.data) }
+
+ . = ALIGN(4);
+ .got : { *(.got) }
+
+ armboot_end_data = .;
+
+ . = ALIGN(4);
+ bss_start = .;
+ .bss : { *(.bss) }
+ bss_end = .;
+
+ armboot_end = .;
+}
diff --git a/board/wepep250/wepep250.c b/board/wepep250/wepep250.c
new file mode 100644
index 0000000..ebf75d7
--- /dev/null
+++ b/board/wepep250/wepep250.c
@@ -0,0 +1,77 @@
+/*
+ * Copyright (C) 2003 ETC s.r.o.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Written by Peter Figuli <peposh@etc.sk>, 2003.
+ *
+ */
+
+#include <common.h>
+#include <asm/arch/pxa-regs.h>
+
+int board_init( void ){
+ DECLARE_GLOBAL_DATA_PTR;
+
+ gd->bd->bi_arch_number = 288;
+ gd->bd->bi_boot_params = 0xa0000000;
+/*
+ * Setup GPIO stuff to get serial working
+ */
+#if defined( CONFIG_FFUART )
+ GPDR1 = 0x80;
+ GAFR1_L = 0x8010;
+#elif defined( CONFIG_BTUART )
+ GPDR1 = 0x800;
+ GAFR1_L = 0x900000;
+#endif
+ PSSR = 0x20;
+
+/*
+ * Following code is just bug workaround, remove it if not neccessary
+ */
+
+ /* cpu/xscale/cpu.c do not set armboot_real_end that is used for
+ malloc pool.*/
+ if( _armboot_real_end == 0xbadc0de ){
+ _armboot_real_end = _armboot_end;
+ }
+ return 0;
+}
+
+int dram_init( void ){
+ DECLARE_GLOBAL_DATA_PTR;
+
+#if ( CONFIG_NR_DRAM_BANKS > 0 )
+ gd->bd->bi_dram[0].start = WEP_SDRAM_1;
+ gd->bd->bi_dram[0].size = WEP_SDRAM_1_SIZE;
+#endif
+#if ( CONFIG_NR_DRAM_BANKS > 1 )
+ gd->bd->bi_dram[1].start = WEP_SDRAM_2;
+ gd->bd->bi_dram[1].size = WEP_SDRAM_2_SIZE;
+#endif
+#if ( CONFIG_NR_DRAM_BANKS > 2 )
+ gd->bd->bi_dram[2].start = WEP_SDRAM_3;
+ gd->bd->bi_dram[2].size = WEP_SDRAM_3_SIZE;
+#endif
+#if ( CONFIG_NR_DRAM_BANKS > 3 )
+ gd->bd->bi_dram[3].start = WEP_SDRAM_4;
+ gd->bd->bi_dram[3].size = WEP_SDRAM_4_SIZE;
+#endif
+
+ return 0;
+}
+