diff options
Diffstat (limited to 'include/configs/taihu.h')
| -rw-r--r-- | include/configs/taihu.h | 146 |
1 files changed, 14 insertions, 132 deletions
diff --git a/include/configs/taihu.h b/include/configs/taihu.h index c060b1e..86f776d 100644 --- a/include/configs/taihu.h +++ b/include/configs/taihu.h @@ -32,6 +32,12 @@ #define CONFIG_4xx 1 /* member of PPC4xx family */ #define CONFIG_TAIHU 1 /* on a taihu board */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME taihu +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f */ #define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */ @@ -70,87 +76,31 @@ #define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ -#define CONFIG_ENV_OVERWRITE 1 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS -#define CONFIG_EXTRA_ENV_SETTINGS \ - "bootfile=/tftpboot/taihu/uImage\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "netdev=eth0\0" \ - "hostname=taihu\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ +/* + * Default environment variables + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_PPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=FC000000\0" \ "ramdisk_addr=FC180000\0" \ - "load=tftp 200000 /tftpboot/taihu/u-boot.bin\0" \ - "update=protect off FFFC0000 FFFFFFFF;era FFFC0000 FFFFFFFF;" \ - "cp.b 200000 FFFC0000 40000\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0x14 /* PHY address */ #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_PHY1_ADDR 0x10 /* EMAC1 PHY address */ -#define CONFIG_NET_MULTI 1 -#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ #define CONFIG_PHY_RESET 1 /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_CACHE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SPI -#undef CONFIG_WATCHDOG /* watchdog disabled */ - #undef CONFIG_SPD_EEPROM /* use SPD EEPROM for setup */ #define CFG_SDRAM_SIZE_PER_BANK 0x04000000 /* 64MB */ #define CFG_SDRAM_BANKS 2 @@ -169,23 +119,6 @@ #define CFG_SDRAM_tRFC 66 /* Auto refresh period */ /* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* print buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/* * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1. * If CFG_405_UART_ERRATA_59, then UART divisor is 31. * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value. @@ -198,35 +131,13 @@ #undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ #undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CFG_BASE_BAUD 691200 - -#define CONFIG_BAUDRATE 115200 - #define CONFIG_UART1_CONSOLE 1 -/* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ - /*----------------------------------------------------------------------- * I2C stuff *----------------------------------------------------------------------- */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_NOPROBES { 0x69 } /* avoid iprobe hangup (why?) */ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ @@ -278,25 +189,12 @@ unsigned char spi_read(void); /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_FLASH_BASE 0xFFE00000 -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ -#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ - #define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ #define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ @@ -421,21 +319,5 @@ unsigned char spi_read(void); #define CPLD_REG0_ADDR 0x50100000 #define CPLD_REG1_ADDR 0x50100001 -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 #endif /* __CONFIG_H */ |