| Age | Commit message (Collapse) | Author |
|---|
|
If the core runs at higher than x3 speed of the platform, there is
possiblity about sev instruction to getting missed by other cores.
This is because of SoC Run Control block may not able to sample
the EVENTI(Sev) signals.
Configure Run Control and EPU to periodically send out EVENTI signals to
wake up A57 cores.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
When one core is released, other cores may not have valid entry
address. Those cores are trapped by "wfe" and wait for further
instruction. When their address is set, they need to be kicked
off by "sev".
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
For most device addresses excution shouldn't be allowed. Revise
the MMU table to enforce execute-never bits. OCRAM, DDR and IFC
are allowed for excution.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reported-by: Zhichun Hua <zhichun.hua@freescale.com>
|
|
The global_data pointer (gd) has been set earlier in crt0_64.S.
So there's no need to assign it again. Remove gdata since it is going
away in U-Boot.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
Dropped #ifdef in cpu.h
Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Management complex Firmware, DPL and DPC are depolyed during u-boot boot
sequence.
Add new DPAA2 commands to manage Management Complex (MC) i.e. start mc, aiop
and apply DPL from u-boot command prompt.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Current implementation only consider SGMIIs for dpmac initialization.
XFI serdes protocols also uses dpmac.
Also, fix lane protocol parsing logic to consider both XFIs and SGMIIs.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Put jump trampoline to TCM at 0 and setup R5 reset address to 0.
Jump trampoline ensures that jump to the right location.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
In order for noncached_init() to operate correctly, SoCs must set up a
custom page table with fine-grained (2MiB) sections, which can be
configured from noncached_init().
This is currently performed by arch/arm/cpu/armv8/{fsl-lsch3,zynqmp}/cpu.c
by cut/pasting and re-implementing mmu_setup, enable_caches(), etc. There
are some other reasons for the duplication there though, such as enabling
icache early, and enabling dcaching earlier with a different configuration.
This change makes mmu_setup() a weak implementation, so that the MMU setup
code can be replaced without having to duplicate other code that calls it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
After the secondary cores enter U-Boot, use CONFIG_ARMV8_MULTIENTRY to
make secondary cores excute in spin loop.
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This patch adds esdhc support for ls1043ardb.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
LS1043ARDB Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 SDRAM (32bit bus)
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* XFI 10G port
* QSGMII with 4x 1G ports
* Two RGMII ports
PCIe:
* PCIe2 (Lanes C) to mini-PCIe slot
* PCIe3 (Lanes D) to PCIe slot
USB 3.0: two super speed USB 3.0 type A ports
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
|
|
Freescale LayerScape with Chassis Generation 2 is a set of SoCs with
ARMv8 cores and 2rd generation of Chassis.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
There are two LS series processors are built on ARMv8 Layersacpe
architecture currently, LS2085A and LS1043A. They are based on
ARMv8 core although use different chassis, so create fsl-layerscape
to refactor the common code for the LS series processors which also
paves the way for adding LS1043A platform.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
be NULL
Pointer 'reg' returned from call to function 'fdt_getprop' may be
NULL, will be passed to function and may be dereferenced there by
passing argument 1 to function 'of_read_number'. So check pointer
'reg' first.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
For EL3 and EL2, the documentation says that bits 31 and 23 are reserved
but should be written as 1.
For EL1, only bit 23 is not reserved, so only write bit 31 as 1.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
|
|
Some platforms have the means to determine the counter frequency at
runtime, so give them an opportunity to do so.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
>From source code comments:
"x0: 0 flush & invalidate, 1 invalidate only"
Current value 0xffff can make invalidate work, since we only judge whether
input value is 0 or not, see following code:
"
tbz w1, #0, 1f
dc isw, x9
b 2f
1: dc cisw, x9 /* clean & invalidate by set/way */
2: subs x6, x6, #1 /* decrement the way */
"
Later we may add "2 clean only" support. So following the comments,
correct value from 0xffff to 1.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
|
|
This patch rewrites MMU translation table entries. To start, all table
entries are written as "invalid", then "device-ngnrnr" and "normal" are
written to the entries to enable access to specific addresses.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
Every QSGMII SerDes Protocol usage 4 MACs.
So add/repeat QSGMII information for 4 MACs in dpmac_info strucuture.
Signed-off-by: King Chung Lo@freescale.com <KingChungLo@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Update 0x33 and 0x35 serdes protocol as per updated SoC document
in array serdes1_cfg_tbl.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This patch adds a minimal framework for Dickens CCN-504
interconnect configuration - mainly related to adding Clusters/cores
to snoop/DVM domain and setting QoS of the RN-I ports.
LS2085A platform makes use of these configurations to support
better network data performance and to boot a SMP Linux.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Added usb dwc3 driver support for zynqmp
this also supports the DFU and LTHOR to download
the linux images on to RAM and cen be booted from
those linux images.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Based on the patch:
"armv8: caches: Added routine to set non cacheable region"
(sha1: dad17fd51027ad02ac8f02deed186d08109d61fd)
it is necessary to add platform specific hook.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Enable Secure IOU setup to enable U-Boot to run in EL3 without
setting from ATF.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch adds basic pinmux support for the hi6220 SoC,
which is found on the hikey board.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
|
|
Current many cpu use the same flush_cache() function, which just call
the flush_dcache_range().
So implement a weak flush_cache() for all the cpus to use.
In original weak flush_cache() in arch/arm/lib/cache.c, there has some
code for ARM1136 & ARM926ejs. But in the arch/arm/cpu/arm1136/cpu.c and
arch/arm/cpu/arm926ejs/cache.c, there implements a real flush_cache()
function as well. That means the original code for ARM1136 & ARM926ejs
in weak flush_cache() of arch/arm/lib/cache.c is totally useless.
So in this patch remove such code in flush_cache() and only call
flush_dcache_range().
Signed-off-by: Josh Wu <josh.wu@atmel.com>
|
|
Since some driver like ohci, lcd used dcache functions. But some ARM
cpu don't implement the invalidate_dcache_range()/flush_dcache_range()
functions.
To avoid compiling errors this patch adds an weak empty stub function
for all ARM cpu in arch/arm/lib/cache.c.
And ARM cpu still can implemnt its own cache functions on the cpu folder.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Added routine mmu_set_region_dcache_behaviour() to set a
particular region as non cacheable.
Define dummy routine for mmu_set_region_dcache_behaviour()
to handle incase of dcache off.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
|
|
|
|
While generating the page tables, a running integer index is shifted by
SECTION_SHIFT (29) and causes overflow for any integer bigger than 7.
The page tables therefore alias to the same 8 sections and cause U-Boot
to hang once the MMU is enabled.
Fix this by making the index a 64-bit unsigned integer and so avoid the
overflow.
swarren notes: currently "i" ranges from 0..8191 on all ARM64 boards, and
"j" varies depending on RAM size; from 4 to 11 for a board with 4GB at
physical address 2GB, as some Tegra boards have.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
SLCR can be used for IP configuration setting.
Add SLCR skeleton to enable run time checking.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Pass directly boot_addr which is LOVEC (0) or HIVEC (0xffff0000).
No reason to use magic values 0 and 1.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Define a new config "zynqmp_ep" for ZynqMP instead
of xilinx_zynqmp. This defconfig supports all emulation
platforms of ZynqMP. Also renamed TARGET_XILINX_ZYNQMP
to ARCH_ZYNQMP.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Move the zynqmp Kconfig from board to arch
as there may be different boards under same
architecture.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
When final MMU table is setup in DDR, TCR attributes must match
those of the memroy for cacheability and shareability.
Signed-off-by: Zhichun Hua <zhichun.hua@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This patch adds the infrastructure to update device
tree nodes to convey SMMU stream IDs in the device
tree. Fixups are implemented for PCI controllers
initially.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This patch updates the setting of required bits for A57 cores erratas
- 828024 and 826974
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Dai Haruki <dai.haruki at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Update SoC README to provide details of
- Memory regions
- Memory used by MC and Debug server
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This patch adds support to print out the SoC personality.
Freescale LS20xx SoCs (compliant to Chassis-3 specifications) can
have 6 personalities: LS2045AE, LS2045A, LS2080AE, LS2080A,
LS2085AE and LS2085A
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
DDR speed should be in MT/s, not MHz.
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
|
|
call ft_pci_setup() to disable PCIe dts node if corresponding
PCIe controller is disabled according to RCW
Signed-off-by: Minghuan Lian <Minghuan.Lian at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Add support for Veloce - zynqmp emulation platform.
Platform doesn't support SDHCI.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add support for loading sw for R5 with enabling for zynqmp.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
|
|
Define the mmu table till 2MB granularity
enable dcaches for zynqmp.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
