1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
|
/*
* (C) Copyright 2003-2006
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* (C) Copyright 2004
* Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <mpc5xxx.h>
#include <net.h>
#include <asm/processor.h>
DECLARE_GLOBAL_DATA_PTR;
#ifndef CONFIG_SYS_RAMBOOT
static void sdram_start(int hi_addr)
{
long hi_addr_bit = hi_addr ? 0x01000000 : 0;
/* unlock mode register */
*(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 | hi_addr_bit;
__asm__ volatile ("sync");
/* precharge all banks */
*(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
__asm__ volatile ("sync");
#if SDRAM_DDR
/* set mode register: extended mode */
*(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
__asm__ volatile ("sync");
/* set mode register: reset DLL */
*(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
__asm__ volatile ("sync");
#endif /* SDRAM_DDR */
/* precharge all banks */
*(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
__asm__ volatile ("sync");
/* auto refresh */
*(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 | hi_addr_bit;
__asm__ volatile ("sync");
/* set mode register */
*(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE;
__asm__ volatile ("sync");
/* normal operation */
*(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
__asm__ volatile ("sync");
}
#endif /* !CONFIG_SYS_RAMBOOT */
int initdram(void)
{
ulong dramsize = 0;
ulong dramsize2 = 0;
uint svr, pvr;
#ifndef CONFIG_SYS_RAMBOOT
ulong test1, test2;
/* setup SDRAM chip selects */
*(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0x0000001e; /* 2G at 0x0 */
*(vu_long *) MPC5XXX_SDRAM_CS1CFG = 0x80000000; /* disabled */
__asm__ volatile ("sync");
/* setup config registers */
*(vu_long *) MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
*(vu_long *) MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
__asm__ volatile ("sync");
#if SDRAM_DDR
/* set tap delay */
*(vu_long *) MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
__asm__ volatile ("sync");
#endif /* SDRAM_DDR */
/* find RAM size using SDRAM CS0 only */
sdram_start(0);
test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
sdram_start(1);
test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
if (test1 > test2) {
sdram_start(0);
dramsize = test1;
} else
dramsize = test2;
/* memory smaller than 1MB is impossible */
if (dramsize < (1 << 20))
dramsize = 0;
/* set SDRAM CS0 size according to the amount of RAM found */
if (dramsize > 0)
*(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0x13 + __builtin_ffs(dramsize >> 20) - 1;
else
*(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
/* let SDRAM CS1 start right after CS0 */
*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e;/* 2G */
/* find RAM size using SDRAM CS1 only */
if (!dramsize)
sdram_start(0);
test2 = test1 = get_ram_size((long *) (CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
if (!dramsize) {
sdram_start(1);
test2 = get_ram_size((long *) (CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
}
if (test1 > test2) {
sdram_start(0);
dramsize2 = test1;
} else
dramsize2 = test2;
/* memory smaller than 1MB is impossible */
if (dramsize2 < (1 << 20))
dramsize2 = 0;
/* set SDRAM CS1 size according to the amount of RAM found */
if (dramsize2 > 0)
*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize
| (0x13 + __builtin_ffs(dramsize2 >> 20) - 1);
else
*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
#else /* CONFIG_SYS_RAMBOOT */
/* retrieve size of memory connected to SDRAM CS0 */
dramsize = *(vu_long *) MPC5XXX_SDRAM_CS0CFG & 0xFF;
if (dramsize >= 0x13)
dramsize = (1 << (dramsize - 0x13)) << 20;
else
dramsize = 0;
/* retrieve size of memory connected to SDRAM CS1 */
dramsize2 = *(vu_long *) MPC5XXX_SDRAM_CS1CFG & 0xFF;
if (dramsize2 >= 0x13)
dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
else
dramsize2 = 0;
#endif /* CONFIG_SYS_RAMBOOT */
/*
* On MPC5200B we need to set the special configuration delay in the
* DDR controller. Please refer to Freescale's AN3221 "MPC5200B SDRAM
* Initialization and Configuration", 3.3.1 SDelay--MBAR + 0x0190:
*
* "The SDelay should be written to a value of 0x00000004. It is
* required to account for changes caused by normal wafer processing
* parameters."
*/
svr = get_svr();
pvr = get_pvr();
if ((SVR_MJREV(svr) >= 2) &&
(PVR_MAJ(pvr) == 1) && (PVR_MIN(pvr) == 4)) {
*(vu_long *) MPC5XXX_SDRAM_SDELAY = 0x04;
__asm__ volatile ("sync");
}
gd->ram_size = dramsize + dramsize2;
return 0;
}
int checkboard (void)
{
puts("Board: MarelV38B\n");
return 0;
}
int board_early_init_f(void)
{
#ifdef CONFIG_HW_WATCHDOG
/*
* Enable and configure the direction (output) of PSC3_9 - watchdog
* reset input. Refer to 7.3.2.2.[1,3,4] of the MPC5200B User's
* Manual.
*/
*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC3_9;
*(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC3_9;
#endif /* CONFIG_HW_WATCHDOG */
return 0;
}
int board_early_init_r(void)
{
/*
* Now, when we are in RAM, enable flash write access for the
* detection process. Note that CS_BOOT cannot be cleared when
* executing in flash.
*/
*(vu_long *) MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */
/*
* Enable GPIO_WKUP_7 to "read the status of the actual power
* situation". Default direction is input, so no need to set it
* explicitly.
*/
*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_WKUP_7;
return 0;
}
extern void board_get_enetaddr(uchar *enetaddr);
int misc_init_r(void)
{
uchar enetaddr[6];
if (!eth_getenv_enetaddr("ethaddr", enetaddr)) {
board_get_enetaddr(enetaddr);
eth_setenv_enetaddr("ethaddr", enetaddr);
}
return 0;
}
#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
void init_ide_reset(void)
{
debug("init_ide_reset\n");
/* Configure PSC1_4 as GPIO output for ATA reset */
*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
*(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC1_4;
/* Deassert reset */
*(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
}
void ide_set_reset(int idereset)
{
debug("ide_reset(%d)\n", idereset);
if (idereset) {
*(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_PSC1_4;
/* Make a delay. MPC5200 spec says 25 usec min */
udelay(500000);
} else
*(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
}
#endif
#ifdef CONFIG_HW_WATCHDOG
void hw_watchdog_reset(void)
{
/*
* MarelV38B has a TPS3705 watchdog. Spec says that to kick the dog
* we need a positive or negative transition on WDI i.e., our PSC3_9.
*/
*(vu_long *) MPC5XXX_WU_GPIO_DATA_O ^= GPIO_PSC3_9;
}
#endif /* CONFIG_HW_WATCHDOG */
|
