blob: 6f9f525936ba2add9128913c5151f004bd51c1c2 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
|
BUBT (Burn ATF) command
--------------------------
Bubt command is used to burn a new ATF image to flash device.
The bubt command gets the following parameters: ATF file name, destination device and source device.
bubt [file-name] [destination [source]]
- file-name Image file name to burn. default = flash-image.bin
- destination Flash to burn to [spi, nand, mmc]. default = active flash
- source Source to load image from [tftp, usb]. default = tftp
Examples:
bubt - Burn flash-image.bin from tftp to active flash
bubt latest-spi.bin nand - Burn latest-spi.bin from tftp to NAND flash
Notes:
- For the TFTP interface set serverip and ipaddr.
- To burn image to SD/eMMC device, the target is defined
by parameters CONFIG_SYS_MMC_ENV_DEV and CONFIG_SYS_MMC_ENV_PART.
Bubt command details (burn image step by-step)
----------------------------------------------
This section describes bubt command flow:
1. Fetch the requested ATF image from an available interface (USB/SD/SATA/XDB, etc.)
into the DRAM, and place it at <load_address>
Example: when using the FAT file system on USB flash device:
# usb reset
# fatls usb 0 (see files in device)
# fatload usb 0 <load_address> <file_name>
2. Erase the target device:
- NAND: # nand erase 0 100000
- SPI: # sf probe 0
# sf erase 0 100000
- SD/eMMC: # mmc dev <dev_id> <boot_partition>
Notes:
- The eMMC has 2 boot partitions (BOOT0 and BOOT1) and a user data partition (DATA).
The boot partitions are numbered as partition 1 and 2 in MMC driver.
Number 0 is used for user data partition and should not be utilized for storing
boot images and U-Boot environment in RAW mode since it will break file system
structures usually located here.
The default boot partition is BOOT0. It is selected by the following parameter:
CONFIG_SYS_MMC_ENV_PART=1
Valid values for this parameter are 1 for BOOT0 and 2 for BOOT1.
Please never use partition number 0 here!
The eMMC has 2 boot partitions (BOOT0 and BOOT1) and a user data partition (DATA).
The boot partitions are numbered as partition 1 and 2 in MMC driver.
Number 0 is used for user data partition and should not be utilized for storing
boot images and U-Boot environment in RAW mode since it will break file system
structures usually located here.
The default boot partition is BOOT0. It is selected by the following parameter:
CONFIG_SYS_MMC_ENV_PART=1
Valid values for this parameter are 1 for BOOT0 and 2 for BOOT1.
Please never use partition number 0 here!
- The partition number is ignored if the target device is SD card.
- The boot image offset starts at block 0 for eMMC and block 1 for SD devices.
The block 0 on SD devices is left for MBR storage.
3. Write the ATF image:
- NAND: # nand write <load_address> 0 <ATF Size>
- SPI: # sf write <load_address> 0 <ATF Size>
- SD/eMMC: # mmc write <load_address> [0|1] <ATF Size>/<block_size>
|
