path: root/drivers/net/zynq_gem.c

/*
 * (C) Copyright 2011 Michal Simek
 *
 * Michal SIMEK <monstr@monstr.eu>
 *
 * Based on Xilinx gmac driver:
 * (C) Copyright 2011 Xilinx
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <clk.h>
#include <common.h>
#include <dm.h>
#include <net.h>
#include <netdev.h>
#include <config.h>
#include <console.h>
#include <malloc.h>
#include <asm/io.h>
#include <phy.h>
#include <miiphy.h>
#include <wait_bit.h>
#include <watchdog.h>
#include <asm/system.h>
#include <asm/arch/hardware.h>
#include <asm/arch/sys_proto.h>
#include <linux/errno.h>

DECLARE_GLOBAL_DATA_PTR;

/* Bit/mask specification */
#define ZYNQ_GEM_PHYMNTNC_OP_MASK	0x40020000 /* operation mask bits */
#define ZYNQ_GEM_PHYMNTNC_OP_R_MASK	0x20000000 /* read operation */
#define ZYNQ_GEM_PHYMNTNC_OP_W_MASK	0x10000000 /* write operation */
#define ZYNQ_GEM_PHYMNTNC_PHYAD_SHIFT_MASK	23 /* Shift bits for PHYAD */
#define ZYNQ_GEM_PHYMNTNC_PHREG_SHIFT_MASK	18 /* Shift bits for PHREG */

#define ZYNQ_GEM_RXBUF_EOF_MASK		0x00008000 /* End of frame. */
#define ZYNQ_GEM_RXBUF_SOF_MASK		0x00004000 /* Start of frame. */
#define ZYNQ_GEM_RXBUF_LEN_MASK		0x00003FFF /* Mask for length field */

#define ZYNQ_GEM_RXBUF_WRAP_MASK	0x00000002 /* Wrap bit, last BD */
#define ZYNQ_GEM_RXBUF_NEW_MASK		0x00000001 /* Used bit.. */
#define ZYNQ_GEM_RXBUF_ADD_MASK		0xFFFFFFFC /* Mask for address */

/* Wrap bit, last descriptor */
#define ZYNQ_GEM_TXBUF_WRAP_MASK	0x40000000
#define ZYNQ_GEM_TXBUF_LAST_MASK	0x00008000 /* Last buffer */
#define ZYNQ_GEM_TXBUF_USED_MASK	0x80000000 /* Used by Hw */

#define ZYNQ_GEM_NWCTRL_TXEN_MASK	0x00000008 /* Enable transmit */
#define ZYNQ_GEM_NWCTRL_RXEN_MASK	0x00000004 /* Enable receive */
#define ZYNQ_GEM_NWCTRL_MDEN_MASK	0x00000010 /* Enable MDIO port */
#define ZYNQ_GEM_NWCTRL_STARTTX_MASK	0x00000200 /* Start tx (tx_go) */

#define ZYNQ_GEM_NWCFG_SPEED100		0x00000001 /* 100 Mbps operation */
#define ZYNQ_GEM_NWCFG_SPEED1000	0x00000400 /* 1Gbps operation */
#define ZYNQ_GEM_NWCFG_FDEN		0x00000002 /* Full Duplex mode */
#define ZYNQ_GEM_NWCFG_FSREM		0x00020000 /* FCS removal */
#define ZYNQ_GEM_NWCFG_SGMII_ENBL	0x08000000 /* SGMII Enable */
#define ZYNQ_GEM_NWCFG_PCS_SEL		0x00000800 /* PCS select */
#ifdef CONFIG_ARM64
#define ZYNQ_GEM_NWCFG_MDCCLKDIV	0x00100000 /* Div pclk by 64, max 160MHz */
#else
#define ZYNQ_GEM_NWCFG_MDCCLKDIV	0x000c0000 /* Div pclk by 48, max 120MHz */
#endif

#ifdef CONFIG_ARM64
# define ZYNQ_GEM_DBUS_WIDTH	(1 << 21) /* 64 bit bus */
#else
# define ZYNQ_GEM_DBUS_WIDTH	(0 << 21) /* 32 bit bus */
#endif

#define ZYNQ_GEM_NWCFG_INIT		(ZYNQ_GEM_DBUS_WIDTH | \
					ZYNQ_GEM_NWCFG_FDEN | \
					ZYNQ_GEM_NWCFG_FSREM | \
					ZYNQ_GEM_NWCFG_MDCCLKDIV)

#define ZYNQ_GEM_NWSR_MDIOIDLE_MASK	0x00000004 /* PHY management idle */

#define ZYNQ_GEM_DMACR_BLENGTH		0x00000004 /* INCR4 AHB bursts */
/* Use full configured addressable space (8 Kb) */
#define ZYNQ_GEM_DMACR_RXSIZE		0x00000300
/* Use full configured addressable space (4 Kb) */
#define ZYNQ_GEM_DMACR_TXSIZE		0x00000400
/* Set with binary 00011000 to use 1536 byte(1*max length frame/buffer) */
#define ZYNQ_GEM_DMACR_RXBUF		0x00180000

#define ZYNQ_GEM_DMACR_INIT		(ZYNQ_GEM_DMACR_BLENGTH | \
					ZYNQ_GEM_DMACR_RXSIZE | \
					ZYNQ_GEM_DMACR_TXSIZE | \
					ZYNQ_GEM_DMACR_RXBUF)

#define ZYNQ_GEM_TSR_DONE		0x00000020 /* Tx done mask */

#define ZYNQ_GEM_PCS_CTL_ANEG_ENBL	0x1000

/* Use MII register 1 (MII status register) to detect PHY */
#define PHY_DETECT_REG  1

/* Mask used to verify certain PHY features (or register contents)
 * in the register above:
 *  0x1000: 10Mbps full duplex support
 *  0x0800: 10Mbps half duplex support
 *  0x0008: Auto-negotiation support
 */
#define PHY_DETECT_MASK 0x1808

/* TX BD status masks */
#define ZYNQ_GEM_TXBUF_FRMLEN_MASK	0x000007ff
#define ZYNQ_GEM_TXBUF_EXHAUSTED	0x08000000
#define ZYNQ_GEM_TXBUF_UNDERRUN		0x10000000

/* Clock frequencies for different speeds */
#define ZYNQ_GEM_FREQUENCY_10	2500000UL
#define ZYNQ_GEM_FREQUENCY_100	25000000UL
#define ZYNQ_GEM_FREQUENCY_1000	125000000UL

/* Device registers */
struct zynq_gem_regs {
	u32 nwctrl; /* 0x0 - Network Control reg */
	u32 nwcfg; /* 0x4 - Network Config reg */
	u32 nwsr; /* 0x8 - Network Status reg */
	u32 reserved1;
	u32 dmacr; /* 0x10 - DMA Control reg */
	u32 txsr; /* 0x14 - TX Status reg */
	u32 rxqbase; /* 0x18 - RX Q Base address reg */
	u32 txqbase; /* 0x1c - TX Q Base address reg */
	u32 rxsr; /* 0x20 - RX Status reg */
	u32 reserved2[2];
	u32 idr; /* 0x2c - Interrupt Disable reg */
	u32 reserved3;
	u32 phymntnc; /* 0x34 - Phy Maintaince reg */
	u32 reserved4[18];
	u32 hashl; /* 0x80 - Hash Low address reg */
	u32 hashh; /* 0x84 - Hash High address reg */
#define LADDR_LOW	0
#define LADDR_HIGH	1
	u32 laddr[4][LADDR_HIGH + 1]; /* 0x8c - Specific1 addr low/high reg */
	u32 match[4]; /* 0xa8 - Type ID1 Match reg */
	u32 reserved6[18];
#define STAT_SIZE	44
	u32 stat[STAT_SIZE]; /* 0x100 - Octects transmitted Low reg */
	u32 reserved9[20];
	u32 pcscntrl;
	u32 reserved7[143];
	u32 transmit_q1_ptr; /* 0x440 - Transmit priority queue 1 */
	u32 reserved8[15];
	u32 receive_q1_ptr; /* 0x480 - Receive priority queue 1 */
};

/* BD descriptors */
struct emac_bd {
	u32 addr; /* Next descriptor pointer */
	u32 status;
};

#define RX_BUF 32
/* Page table entries are set to 1MB, or multiples of 1MB
 * (not < 1MB). driver uses less bd's so use 1MB bdspace.
 */
#define BD_SPACE	0x100000
/* BD separation space */
#define BD_SEPRN_SPACE	(RX_BUF * sizeof(struct emac_bd))

/* Setup the first free TX descriptor */
#define TX_FREE_DESC	2

/* Initialized, rxbd_current, rx_first_buf must be 0 after init */
struct zynq_gem_priv {
	struct emac_bd *tx_bd;
	struct emac_bd *rx_bd;
	char *rxbuffers;
	u32 rxbd_current;
	u32 rx_first_buf;
	int phyaddr;
	int init;
	struct zynq_gem_regs *iobase;
	phy_interface_t interface;
	struct phy_device *phydev;
	int phy_of_handle;
	struct mii_dev *bus;
	struct clk clk;
};

static u32 phy_setup_op(struct zynq_gem_priv *priv, u32 phy_addr, u32 regnum,
			u32 op, u16 *data)
{
	u32 mgtcr;
	struct zynq_gem_regs *regs = priv->iobase;
	int err;

	err = wait_for_bit(__func__, &regs->nwsr, ZYNQ_GEM_NWSR_MDIOIDLE_MASK,
			    true, 20000, false);
	if (err)
		return err;

	/* Construct mgtcr mask for the operation */
	mgtcr = ZYNQ_GEM_PHYMNTNC_OP_MASK | op |
		(phy_addr << ZYNQ_GEM_PHYMNTNC_PHYAD_SHIFT_MASK) |
		(regnum << ZYNQ_GEM_PHYMNTNC_PHREG_SHIFT_MASK) | *data;

	/* Write mgtcr and wait for completion */
	writel(mgtcr, &regs->phymntnc);

	err = wait_for_bit(__func__, &regs->nwsr, ZYNQ_GEM_NWSR_MDIOIDLE_MASK,
			    true, 20000, false);
	if (err)
		return err;

	if (op == ZYNQ_GEM_PHYMNTNC_OP_R_MASK)
		*data = readl(&regs->phymntnc);

	return 0;
}

static u32 phyread(struct zynq_gem_priv *priv, u32 phy_addr,
		   u32 regnum, u16 *val)
{
	u32 ret;

	ret = phy_setup_op(priv, phy_addr, regnum,
			   ZYNQ_GEM_PHYMNTNC_OP_R_MASK, val);

	if (!ret)
		debug("%s: phy_addr %d, regnum 0x%x, val 0x%x\n", __func__,
		      phy_addr, regnum, *val);

	return ret;
}

static u32 phywrite(struct zynq_gem_priv *priv, u32 phy_addr,
		    u32 regnum, u16 data)
{
	debug("%s: phy_addr %d, regnum 0x%x, data 0x%x\n", __func__, phy_addr,
	      regnum, data);

	return phy_setup_op(priv, phy_addr, regnum,
			    ZYNQ_GEM_PHYMNTNC_OP_W_MASK, &data);
}

static int phy_detection(struct udevice *dev)
{
	int i;
	u16 phyreg;
	struct zynq_gem_priv *priv = dev->priv;

	if (priv->phyaddr != -1) {
		phyread(priv, priv->phyaddr, PHY_DETECT_REG, &phyreg);
		if ((phyreg != 0xFFFF) &&
		    ((phyreg & PHY_DETECT_MASK) == PHY_DETECT_MASK)) {
			/* Found a valid PHY address */
			debug("Default phy address %d is valid\n",
			      priv->phyaddr);
			return 0;
		} else {
			debug("PHY address is not setup correctly %d\n",
			      priv->phyaddr);
			priv->phyaddr = -1;
		}
	}

	debug("detecting phy address\n");
	if (priv->phyaddr == -1) {
		/* detect the PHY address */
		for (i = 31; i >= 0; i--) {
			phyread(priv, i, PHY_DETECT_REG, &phyreg);
			if ((phyreg != 0xFFFF) &&
			    ((phyreg & PHY_DETECT_MASK) == PHY_DETECT_MASK)) {
				/* Found a valid PHY address */
				priv->phyaddr = i;
				debug("Found valid phy address, %d\n", i);
				return 0;
			}
		}
	}
	printf("PHY is not detected\n");
	return -1;
}

static int zynq_gem_setup_mac(struct udevice *dev)
{
	u32 i, macaddrlow, macaddrhigh;
	struct eth_pdata *pdata = dev_get_platdata(dev);
	struct zynq_gem_priv *priv = dev_get_priv(dev);
	struct zynq_gem_regs *regs = priv->iobase;

	/* Set the MAC bits [31:0] in BOT */
	macaddrlow = pdata->enetaddr[0];
	macaddrlow |= pdata->enetaddr[1] << 8;
	macaddrlow |= pdata->enetaddr[2] << 16;
	macaddrlow |= pdata->enetaddr[3] << 24;

	/* Set MAC bits [47:32] in TOP */
	macaddrhigh = pdata->enetaddr[4];
	macaddrhigh |= pdata->enetaddr[5] << 8;

	for (i = 0; i < 4; i++) {
		writel(0, &regs->laddr[i][LADDR_LOW]);
		writel(0, &regs->laddr[i][LADDR_HIGH]);
		/* Do not use MATCHx register */
		writel(0, &regs->match[i]);
	}

	writel(macaddrlow, &regs->laddr[0][LADDR_LOW]);
	writel(macaddrhigh, &regs->laddr[0][LADDR_HIGH]);

	return 0;
}

static int zynq_phy_init(struct udevice *dev)
{
	int ret;
	struct zynq_gem_priv *priv = dev_get_priv(dev);
	struct zynq_gem_regs *regs = priv->iobase;
	const u32 supported = SUPPORTED_10baseT_Half |
			SUPPORTED_10baseT_Full |
			SUPPORTED_100baseT_Half |
			SUPPORTED_100baseT_Full |
			SUPPORTED_1000baseT_Half |
			SUPPORTED_1000baseT_Full;

	/* Enable only MDIO bus */
	writel(ZYNQ_GEM_NWCTRL_MDEN_MASK, &regs->nwctrl);

	if (priv->interface != PHY_INTERFACE_MODE_SGMII) {
		ret = phy_detection(dev);
		if (ret) {
			printf("GEM PHY init failed\n");
			return ret;
		}
	}

	priv->phydev = phy_connect(priv->bus, priv->phyaddr, dev,
				   priv->interface);
	if (!priv->phydev)
		return -ENODEV;

	priv->phydev->supported &= supported | ADVERTISED_Pause |
				  ADVERTISED_Asym_Pause;
	priv->phydev->advertising = priv->phydev->supported;

	if (priv->phy_of_handle > 0)
		dev_set_of_offset(priv->phydev->dev, priv->phy_of_handle);

	return phy_config(priv->phydev);
}

static int zynq_gem_init(struct udevice *dev)
{
	u32 i, nwconfig;
	int ret;
	unsigned long clk_rate = 0;
	struct zynq_gem_priv *priv = dev_get_priv(dev);
	struct zynq_gem_regs *regs = priv->iobase;
	struct emac_bd *dummy_tx_bd = &priv->tx_bd[TX_FREE_DESC];
	struct emac_bd *dummy_rx_bd = &priv->tx_bd[TX_FREE_DESC + 2];

	if (!priv->init) {
		/* Disable all interrupts */
		writel(0xFFFFFFFF, &regs->idr);

		/* Disable the receiver & transmitter */
		writel(0, &regs->nwctrl);
		writel(0, &regs->txsr);
		writel(0, &regs->rxsr);
		writel(0, &regs->phymntnc);

		/* Clear the Hash registers for the mac address
		 * pointed by AddressPtr
		 */
		writel(0x0, &regs->hashl);
		/* Write bits [63:32] in TOP */
		writel(0x0, &regs->hashh);

		/* Clear all counters */
		for (i = 0; i < STAT_SIZE; i++)
			readl(&regs->stat[i]);

		/* Setup RxBD space */
		memset(priv->rx_bd, 0, RX_BUF * sizeof(struct emac_bd));

		for (i = 0; i < RX_BUF; i++) {
			priv->rx_bd[i].status = 0xF0000000;
			priv->rx_bd[i].addr =
					((ulong)(priv->rxbuffers) +
							(i * PKTSIZE_ALIGN));
		}
		/* WRAP bit to last BD */
		priv->rx_bd[--i].addr |= ZYNQ_GEM_RXBUF_WRAP_MASK;
		/* Write RxBDs to IP */
		writel((ulong)priv->rx_bd, &regs->rxqbase);

		/* Setup for DMA Configuration register */
		writel(ZYNQ_GEM_DMACR_INIT, &regs->dmacr);

		/* Setup for Network Control register, MDIO, Rx and Tx enable */
		setbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_MDEN_MASK);

		/* Disable the second priority queue */
		dummy_tx_bd->addr = 0;
		dummy_tx_bd->status = ZYNQ_GEM_TXBUF_WRAP_MASK |
				ZYNQ_GEM_TXBUF_LAST_MASK|
				ZYNQ_GEM_TXBUF_USED_MASK;

		dummy_rx_bd->addr = ZYNQ_GEM_RXBUF_WRAP_MASK |
				ZYNQ_GEM_RXBUF_NEW_MASK;
		dummy_rx_bd->status = 0;

		writel((ulong)dummy_tx_bd, &regs->transmit_q1_ptr);
		writel((ulong)dummy_rx_bd, &regs->receive_q1_ptr);

		priv->init++;
	}

	ret = phy_startup(priv->phydev);
	if (ret)
		return ret;

	if (!priv->phydev->link) {
		printf("%s: No link.\n", priv->phydev->dev->name);
		return -1;
	}

	nwconfig = ZYNQ_GEM_NWCFG_INIT;

	if (priv->interface == PHY_INTERFACE_MODE_SGMII) {
		nwconfig |= ZYNQ_GEM_NWCFG_SGMII_ENBL |
			    ZYNQ_GEM_NWCFG_PCS_SEL;
#ifdef CONFIG_ARM64
		writel(readl(&regs->pcscntrl) | ZYNQ_GEM_PCS_CTL_ANEG_ENBL,
		       &regs->pcscntrl);
#endif
	}

	switch (priv->phydev->speed) {
	case SPEED_1000:
		writel(nwconfig | ZYNQ_GEM_NWCFG_SPEED1000,
		       &regs->nwcfg);
		clk_rate = ZYNQ_GEM_FREQUENCY_1000;
		break;
	case SPEED_100:
		writel(nwconfig | ZYNQ_GEM_NWCFG_SPEED100,
		       &regs->nwcfg);
		clk_rate = ZYNQ_GEM_FREQUENCY_100;
		break;
	case SPEED_10:
		clk_rate = ZYNQ_GEM_FREQUENCY_10;
		break;
	}

	ret = clk_set_rate(&priv->clk, clk_rate);
	if (IS_ERR_VALUE(ret) && ret != (unsigned long)-ENOSYS) {
		dev_err(dev, "failed to set tx clock rate\n");
		return ret;
	}

	ret = clk_enable(&priv->clk);
	if (ret && ret != -ENOSYS) {
		dev_err(dev, "failed to enable tx clock\n");
		return ret;
	}

	setbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_RXEN_MASK |
					ZYNQ_GEM_NWCTRL_TXEN_MASK);

	return 0;
}

static int zynq_gem_send(struct udevice *dev, void *ptr, int len)
{
	u32 addr, size;
	struct zynq_gem_priv *priv = dev_get_priv(dev);
	struct zynq_gem_regs *regs = priv->iobase;
	struct emac_bd *current_bd = &priv->tx_bd[1];

	/* Setup Tx BD */
	memset(priv->tx_bd, 0, sizeof(struct emac_bd));

	priv->tx_bd->addr = (ulong)ptr;
	priv->tx_bd->status = (len & ZYNQ_GEM_TXBUF_FRMLEN_MASK) |
			       ZYNQ_GEM_TXBUF_LAST_MASK;
	/* Dummy descriptor to mark it as the last in descriptor chain */
	current_bd->addr = 0x0;
	current_bd->status = ZYNQ_GEM_TXBUF_WRAP_MASK |
			     ZYNQ_GEM_TXBUF_LAST_MASK|
			     ZYNQ_GEM_TXBUF_USED_MASK;

	/* setup BD */
	writel((ulong)priv->tx_bd, &regs->txqbase);

	addr = (ulong) ptr;
	addr &= ~(ARCH_DMA_MINALIGN - 1);
	size = roundup(len, ARCH_DMA_MINALIGN);
	flush_dcache_range(addr, addr + size);

	addr = (ulong)priv->rxbuffers;
	addr &= ~(ARCH_DMA_MINALIGN - 1);
	size = roundup((RX_BUF * PKTSIZE_ALIGN), ARCH_DMA_MINALIGN);
	flush_dcache_range(addr, addr + size);
	barrier();

	/* Start transmit */
	setbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_STARTTX_MASK);

	/* Read TX BD status */
	if (priv->tx_bd->status & ZYNQ_GEM_TXBUF_EXHAUSTED)
		printf("TX buffers exhausted in mid frame\n");

	return wait_for_bit(__func__, &regs->txsr, ZYNQ_GEM_TSR_DONE,
			    true, 20000, true);
}

/* Do not check frame_recd flag in rx_status register 0x20 - just poll BD */
static int zynq_gem_recv(struct udevice *dev, int flags, uchar **packetp)
{
	int frame_len;
	u32 addr;
	struct zynq_gem_priv *priv = dev_get_priv(dev);
	struct emac_bd *current_bd = &priv->rx_bd[priv->rxbd_current];

	if (!(current_bd->addr & ZYNQ_GEM_RXBUF_NEW_MASK))
		return -1;

	if (!(current_bd->status &
			(ZYNQ_GEM_RXBUF_SOF_MASK | ZYNQ_GEM_RXBUF_EOF_MASK))) {
		printf("GEM: SOF or EOF not set for last buffer received!\n");
		return -1;
	}

	frame_len = current_bd->status & ZYNQ_GEM_RXBUF_LEN_MASK;
	if (!frame_len) {
		printf("%s: Zero size packet?\n", __func__);
		return -1;
	}

	addr = current_bd->addr & ZYNQ_GEM_RXBUF_ADD_MASK;
	addr &= ~(ARCH_DMA_MINALIGN - 1);
	*packetp = (uchar *)(uintptr_t)addr;

	return frame_len;
}

static int zynq_gem_free_pkt(struct udevice *dev, uchar *packet, int length)
{
	struct zynq_gem_priv *priv = dev_get_priv(dev);
	struct emac_bd *current_bd = &priv->rx_bd[priv->rxbd_current];
	struct emac_bd *first_bd;

	if (current_bd->status & ZYNQ_GEM_RXBUF_SOF_MASK) {
		priv->rx_first_buf = priv->rxbd_current;
	} else {
		current_bd->addr &= ~ZYNQ_GEM_RXBUF_NEW_MASK;
		current_bd->status = 0xF0000000; /* FIXME */
	}

	if (current_bd->status & ZYNQ_GEM_RXBUF_EOF_MASK) {
		first_bd = &priv->rx_bd[priv->rx_first_buf];
		first_bd->addr &= ~ZYNQ_GEM_RXBUF_NEW_MASK;
		first_bd->status = 0xF0000000;
	}

	if ((++priv->rxbd_current) >= RX_BUF)
		priv->rxbd_current = 0;

	return 0;
}

static void zynq_gem_halt(struct udevice *dev)
{
	struct zynq_gem_priv *priv = dev_get_priv(dev);
	struct zynq_gem_regs *regs = priv->iobase;

	clrsetbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_RXEN_MASK |
						ZYNQ_GEM_NWCTRL_TXEN_MASK, 0);
}

__weak int zynq_board_read_rom_ethaddr(unsigned char *ethaddr)
{
	return -ENOSYS;
}

static int zynq_gem_read_rom_mac(struct udevice *dev)
{
	struct eth_pdata *pdata = dev_get_platdata(dev);

	if (!pdata)
		return -ENOSYS;

	return zynq_board_read_rom_ethaddr(pdata->enetaddr);
}

static int zynq_gem_miiphy_read(struct mii_dev *bus, int addr,
				int devad, int reg)
{
	struct zynq_gem_priv *priv = bus->priv;
	int ret;
	u16 val;

	ret = phyread(priv, addr, reg, &val);
	debug("%s 0x%x, 0x%x, 0x%x, 0x%x\n", __func__, addr, reg, val, ret);
	return val;
}

static int zynq_gem_miiphy_write(struct mii_dev *bus, int addr, int devad,
				 int reg, u16 value)
{
	struct zynq_gem_priv *priv = bus->priv;

	debug("%s 0x%x, 0x%x, 0x%x\n", __func__, addr, reg, value);
	return phywrite(priv, addr, reg, value);
}

static int zynq_gem_probe(struct udevice *dev)
{
	void *bd_space;
	struct zynq_gem_priv *priv = dev_get_priv(dev);
	int ret;

	/* Align rxbuffers to ARCH_DMA_MINALIGN */
	priv->rxbuffers = memalign(ARCH_DMA_MINALIGN, RX_BUF * PKTSIZE_ALIGN);
	memset(priv->rxbuffers, 0, RX_BUF * PKTSIZE_ALIGN);

	/* Align bd_space to MMU_SECTION_SHIFT */
	bd_space = memalign(1 << MMU_SECTION_SHIFT, BD_SPACE);
	mmu_set_region_dcache_behaviour((phys_addr_t)bd_space,
					BD_SPACE, DCACHE_OFF);

	/* Initialize the bd spaces for tx and rx bd's */
	priv->tx_bd = (struct emac_bd *)bd_space;
	priv->rx_bd = (struct emac_bd *)((ulong)bd_space + BD_SEPRN_SPACE);

	ret = clk_get_by_name(dev, "tx_clk", &priv->clk);
	if (ret < 0) {
		dev_err(dev, "failed to get clock\n");
		return -EINVAL;
	}

	priv->bus = mdio_alloc();
	priv->bus->read = zynq_gem_miiphy_read;
	priv->bus->write = zynq_gem_miiphy_write;
	priv->bus->priv = priv;

	ret = mdio_register_seq(priv->bus, dev->seq);
	if (ret)
		return ret;

	return zynq_phy_init(dev);
}

static int zynq_gem_remove(struct udevice *dev)
{
	struct zynq_gem_priv *priv = dev_get_priv(dev);

	free(priv->phydev);
	mdio_unregister(priv->bus);
	mdio_free(priv->bus);

	return 0;
}

static const struct eth_ops zynq_gem_ops = {
	.start			= zynq_gem_init,
	.send			= zynq_gem_send,
	.recv			= zynq_gem_recv,
	.free_pkt		= zynq_gem_free_pkt,
	.stop			= zynq_gem_halt,
	.write_hwaddr		= zynq_gem_setup_mac,
	.read_rom_hwaddr	= zynq_gem_read_rom_mac,
};

static int zynq_gem_ofdata_to_platdata(struct udevice *dev)
{
	struct eth_pdata *pdata = dev_get_platdata(dev);
	struct zynq_gem_priv *priv = dev_get_priv(dev);
	int node = dev_of_offset(dev);
	const char *phy_mode;

	pdata->iobase = (phys_addr_t)devfdt_get_addr(dev);
	priv->iobase = (struct zynq_gem_regs *)pdata->iobase;
	/* Hardcode for now */
	priv->phyaddr = -1;

	priv->phy_of_handle = fdtdec_lookup_phandle(gd->fdt_blob, node,
						    "phy-handle");
	if (priv->phy_of_handle > 0)
		priv->phyaddr = fdtdec_get_int(gd->fdt_blob,
					priv->phy_of_handle, "reg", -1);

	phy_mode = fdt_getprop(gd->fdt_blob, node, "phy-mode", NULL);
	if (phy_mode)
		pdata->phy_interface = phy_get_interface_by_name(phy_mode);
	if (pdata->phy_interface == -1) {
		debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode);
		return -EINVAL;
	}
	priv->interface = pdata->phy_interface;

	printf("ZYNQ GEM: %lx, phyaddr %x, interface %s\n", (ulong)priv->iobase,
	       priv->phyaddr, phy_string_for_interface(priv->interface));

	return 0;
}

static const struct udevice_id zynq_gem_ids[] = {
	{ .compatible = "cdns,zynqmp-gem" },
	{ .compatible = "cdns,zynq-gem" },
	{ .compatible = "cdns,gem" },
	{ }
};

U_BOOT_DRIVER(zynq_gem) = {
	.name	= "zynq_gem",
	.id	= UCLASS_ETH,
	.of_match = zynq_gem_ids,
	.ofdata_to_platdata = zynq_gem_ofdata_to_platdata,
	.probe	= zynq_gem_probe,
	.remove	= zynq_gem_remove,
	.ops	= &zynq_gem_ops,
	.priv_auto_alloc_size = sizeof(struct zynq_gem_priv),
	.platdata_auto_alloc_size = sizeof(struct eth_pdata),
};